Allow to configure the number of maximum sectors per write command
through sysfs. This makes it easier to tune write command sizes for
different controller configurations.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace bi_error with a new bi_status to allow for a clear conversion.
Note that device mapper overloaded bi_error with a private value, which
we'll have to keep arround at least for now and thus propagate to a
proper blk_status_t value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When block erases fail, these blocks are marked bad. The number of valid
blocks in the line was not updated, which could cause an infinite loop
on the erase path.
Fix this atomic counter and, in order to avoid taking an irq lock on the
interrupt context, make the erase counters atomic too.
Also, in the case that a significant number of blocks become bad in a
line, the result is the double shared metadata buffer (emeta) to stop
the pipeline until all metadata is flushed to the media. Increase the
number of metadata lines from 2 to 4 to avoid this case.
Fixes: a4bd217b43 "lightnvm: physical block device (pblk) target"
Signed-off-by: Javier González <javier@cnexlabs.com>
Reviewed-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When a line allocation fails, for example, due to having too many bad
blocks, free its metadata correctly.
Fixes: a4bd217b43 "lightnvm: physical block device (pblk) target"
Signed-off-by: Javier González <javier@cnexlabs.com>
Reviewed-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When a pblk line fails (or is recovered), make sure to take the line
management lock.
Fixes: a4bd217b43 "lightnvm: physical block device (pblk) target"
Signed-off-by: Javier González <javier@cnexlabs.com>
Reviewed-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
