Commit Graph

183349 Commits

Author SHA1 Message Date
Anand Gadiyar
452f039437 usb: musb: hsdma: add wrapper for reading DMA count
Add a wrapper for reading the DMA count register, analogous
to the one for writing to this register.

Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:41 -08:00
Ajay Kumar Gupta
3b151526ed USB: musb: Add new fifo table for a OMAP3 errata
We have observed MSC data read corruption when USB LAN device is
also connected and it's interface is up.

Silicon team has confirmed an errata where in all the active
transfers should use FIFO space either in first 8K or next 8K.
So far we have observed the issue in above use case scenario.

As a workaround to it, adding a new FIFO config (5) fitting well
within first 8K which can be used for such use cases.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:41 -08:00
Felipe Balbi
8f20960cd7 usb: otg: twl4030: move to request_threaded_irq
move to request_threaded_irq() on twl4030 children.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:40 -08:00
Robert P. J. Day
c9188ad25d USB: Correct CONFIG variable typo.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:40 -08:00
Oliver Neukum
3a90f81872 USB: usblp: Remove checks no longer needed with the new runtime PM system
Under the new system a device cannot be suspended against
the driver's wish. Therefore this condition no longer needs
to be checked for.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:39 -08:00
Johan Hovold
c1284d7726 USB: ftdi_sio: remove unnecessary initialisations
Return values are being initialised to zero only to be unconditionally
assigned to a few instructions later. This may give the impression that
zero is returned on success, which is not the case.

Note also that ftdi_NDI_device_setup never reports errors.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:39 -08:00
Johan Hovold
a3f8168b7a USB: ftdi_sio: clean up modem status handling
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:38 -08:00
Johan Hovold
66e47e6006 USB: ftdi_sio: fix DMA buffers on stack
Also remove unnecessary buffer allocations for zero-length transfers.

Reported-by: Matti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:37 -08:00
Johan Hovold
54f328d0c7 USB: ftdi_sio: fix latency-timeout endianess bug
Also fixes DMA transfer to stack for latency buffer.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:37 -08:00
Johan Hovold
4357369d02 USB: ftdi_sio: use error code from usb stack in read_latency_timer
Use same semantics as for write_latency_timer.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:36 -08:00
Greg Kroah-Hartman
551cdbbeb1 USB: rename USB_SPEED_VARIABLE to USB_SPEED_WIRELESS
It's really the wireless speed, so rename the thing to make
more sense.  Based on a recommendation from David Vrabel

Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:36 -08:00
Dan Streetman
16985408b5 USB: retain USB device power/wakeup setting across reconfiguration
Currently a non-root-hub USB device's wakeup settings are initialized when the
device is set to a configured state using device_init_wakeup(), but this is not
correct as wakeup is split into "capable" (can_wakeup) and "enabled"
(should_wakeup).  The settings should be initialized instead in the device
initialization (usb_new_device) with the "capable" setting disabled and the
"enabled" setting enabled.  The "capable" setting should be set based on the
device being configured or unconfigured, and "enabled" setting set based on
the sysfs power/wakeup control.

This patch retains the sysfs power/wakeup setting of a non-root-hub USB device
over a USB device re-configuration, which can happen (for example) after a
suspend/resume cycle.

Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:35 -08:00
Julian Calaby
ce126644aa USB: cdc_acm: Silence "It is not a modem." error for pbLua devices
The pbLua console port is known to not be a modem, so it is
unnecessary to be told this when it is plugged in.

Add NOT_A_MODEM quirk to tell the driver that we know this already
and hence not to warn us, and mark the pbLua console port.

Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:32 -08:00
Julian Calaby
7c5d8c394a USB: cdc_acm: Add support for pbLua console port
The pbLua firmware (http://pblua.com/) for the Lego Mindstorms NXT
provides a CDC ACM port for it's serial console.

This used to be detected automatically, but this support has been
dropped, probably for sensible reasons.

Explicitly add support for this device by adding an item to the
device ID table.

Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:31 -08:00
Pete Zaitcev
2bc0d10932 usbmon: add bus number to text API
Due to a simple oversight when bus zero was added, the text API fails to
deliver the bus number in 'E' messages (which are equivalent of 'C'
messages, only for error case). This makes it harder, for instance,
use a search-and-highlight in a text editor. So fix it.

Also, Alan Stern requested adding timestamps to 'E' messages. This is
purely cosmetic, but makes it easier to read the trace. This is done
for both text and binary APIs.

Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:30 -08:00
Felipe Balbi
7ed069c12c USB: musb: remove some of the never defined defines
just makes the musb init code a bit cleaner.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:29 -08:00
Felipe Balbi
94375751d1 USB: musb: move to sysfs_groups
it's easier to keep up and add more sysfs entries
as necessary.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:29 -08:00
Felipe Balbi
b3b1cc3ba6 USB: musb: move two printk to dev_err
trivial cleanup, no functional changes.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:29 -08:00
Felipe Balbi
195e9e4691 USB: musb: use resource_size()
it makes ioremap() usage looks cleaner.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:28 -08:00
Cliff Cai
767ffec15e USB: gadget: add INT support for Blackfin musb
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:28 -08:00
Bryan Wu
3a8a3b1cee USB: gadget: use ep5 for bulk-in and ep6 for bulk-out for Blackfin MUSB
Normally, the musb uses ep1 as the bidirectional bulk endpoint.  This won't
work on the Blackfin musb as all endpoints (except ep0) are unidirectional.
Further, ep1-ep4 have a small 128 byte FIFO which makes them undesirable
for bulk endpoints (which need more like a 512 byte FIFO).  This leaves us
with ep5-ep7 which have 1024 byte FIFOs and can be configured as either
in/out and bulk/interrupt/iso on the fly.

Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:28 -08:00
Michael Hennerich
ca0e9485af USB: host: SL811: allow the hcd on Blackfin systems
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:27 -08:00
Michael Hennerich
8ca5bfab15 USB: host: SL811: fix unaligned accesses
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:26 -08:00
Julia Lawall
6ebb7d1b4b USB: isp1362: Use kzalloc for allocating only one thing
Use kzalloc rather than kcalloc(1,...)

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
@@

- kcalloc(1,
+ kzalloc(
          ...)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:25 -08:00
Mike Frysinger
c312659c5f USB: cypress_m8: allow unstable baud rates
I've got a crappy cypress converter here, and while running at higher
baud rates craps out on throughput, it works fine with lower ones.
While it'd be nice to simply use a lower baud rate, not all devices
can be configured this way, and it is possible to (slowly) interact
at higher rates by sending a byte at a time.  So let people force
higher rates when they need it via a module parameter.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:24 -08:00
Mike Frysinger
2805eb13c3 USB: cypress_m8: unify confusing new baudrate check
The current code has a confusing duplicate new_baudrate init when setting
the serial parameters.  So just combine the if statement checks to avoid
this.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:24 -08:00
Mike Frysinger
64319dd74f USB: cypress_m8: stop using USB debug driver config
The USB_SERIAL_DEBUG Kconfig is for the USB serial debug driver, not for
generically enabling debug output in random USB serial drivers.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:24 -08:00
Oliver Neukum
ef955341f6 USB: Export QUIRK_RESET_MORPHS through sysfs
Some devices which use mode switching revert to their
primary mode as they are reset. They must not be reset for
error handling. As user spaces makes the switch it also
has to tell the kernel that a device is quirky.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:23 -08:00
Oliver Neukum
5d3987796c USB: storage: Never reset devices that will morph to an old mode
Some devices must be switched to a new mode to fully use them.
A reset would make them revert to the old mode. Therefore a reset
must not be used for error handling with such devices.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:23 -08:00
Felipe Balbi
d1b5b5c0a8 USB: otg: twl4030: add support for notifier
it's expected that the transceiver driver will
initialize and call the notifier chain when
necessary. Implement that for twl4030-usb driver.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:21 -08:00
Felipe Balbi
e9a20171df USB: otg: add notifier support
The notifier will be used to communicate usb events
to other drivers like the charger chip.

This can be used as source of information to kick
usb charger detection as described by the USB
Battery Charging Specification 1.1 and/or to
pass bMaxPower field of selected usb_configuration
to charger chip in order to use that information
as input current on the charging profile
setup.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:21 -08:00
Julia Lawall
8bc1d21776 USB: wusb: check CHID is all zeros before stopping the host
An incorrect sizeof() resulted in only 4 (or 8) octets of the CHID being
checked instead of all 16 octets.  A randomly generated CHID had a
probability of being unable to start a WUSB host of less than 1 in
2 billion.

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:20 -08:00
Oliver Neukum
319c3ea451 USB: xhci: No GFP_KERNEL in block error handling
xhci_add_endpoint() is used in the reset path. It must
use GFP_NOIO to avoid a possible deadlock.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:19 -08:00
Oliver Neukum
97d35f9555 USB: cdc-acm: Update to new autopm API
Update cdc-acm to the async methods eliminating the workqueue

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:19 -08:00
H Hartley Sweeten
1f141ca2b1 USB: ehci-au1xxx.c: use platform_get_resource() and resource_size()
Use platform_get_resource() to fetch the memory resource and
resource_size() for calculate the length.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:18 -08:00
H Hartley Sweeten
f65c3540d3 USB: ehci-atmel.c: use resource_size()
Use resource_size().

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:18 -08:00
H Hartley Sweeten
5672b7e6a9 USB: ehci-orion.c: use resource_size()
Use resource_size().

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:17 -08:00
H Hartley Sweeten
d8bb0fd26b USB: at91_udc.c: use resource_size()
Use resource_size().

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:17 -08:00
H Hartley Sweeten
3ba37bdaef USB: atmel_usba_udc.c: use resource_size()
Use resource_size().

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:17 -08:00
H Hartley Sweeten
5c90e314a6 USB: pxa27x_udc.c: use resource_size()
Use resource_size().

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:16 -08:00
Anton Vorontsov
1af1077442 USB: ehci-fsl: Add power management support
EHCI FSL controller preserve its state during sleep mode, so nothing
fancy needs to be done.

Though, during 'deep sleep' mode (as found in MPC831x CPUs) the
controller turns off and needs to be reinitialized upon resume.

This patch adds support for hibernation and resuming after deep sleep.
Based on Dave Liu and Jerry Huang's work[1].

[1] http://www.bitshrine.org/gpp/linux-fsl-2.6.24.3-MPC8315ERDB-usb-power-mangement.patch

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:15 -08:00
Anton Vorontsov
dad3843f03 USB: ehci-fsl: Fix sparse warnings
This patch fixes following warnings:

ehci-fsl.c:43:5: warning: symbol 'usb_hcd_fsl_probe' was not declared. Should it be static?
ehci-fsl.c:150:6: warning: symbol 'usb_hcd_fsl_remove' was not declared. Should it be static?

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:14 -08:00
Dmitri Epshtein
22e186948a USB: ehci: fix audio record functionality for some Full speed sound blaster devices
This patch fix audio record functionality for some Full speed sound blaster devices.
Issue: Sometimes transaction complete indication is coming from HW one frame later.
Solution: If scan_periodic process now frame or previous frame now-1 and sitd transaction
is not finished yet, exit scan_periodic function and check the same transaction in the next frame.

Signed-off-by: Dimitry Epshtein <dima@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:13 -08:00
Dmitri Epshtein
d63c66d2d0 USB: ehci: add call of free_cached_itd_list() function in disable_periodic()
Sometimes disable_periodic() stop scan_periodic before than free_cached_itd_list() was called.
In such case USB Host stacked during disconnect operation
Solution: add call of free_cached_itd_list() function in disable_periodic()

Signed-off-by: Dimitry Epshtein <dima@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:13 -08:00
Sarah Sharp
a5f0efaba4 USB: Add call to notify xHC of a device reset.
Add a new host controller driver method, reset_device(), that the USB core
will use to notify the host of a successful device reset.  The call may
fail due to out-of-memory errors; attempt the port reset sequence again if
that happens.  Update hub_port_init() to allow resetting a configured
device.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:12 -08:00
Sarah Sharp
2a8f82c4ce USB: xhci: Notify the xHC when a device is reset.
When a USB device is reset, the xHCI hardware must know, in order to match
the device state and disable all endpoints except control endpoint 0.
Issue a Reset Device command after a USB device is successfully reset.
Wait on the command to finish, and then cache or free the disabled
endpoint rings.

There are four different USB device states that the xHCI hardware tracks:
 - disabled/enabled - device connection has just been detected,
 - default - the device has been reset and has an address of 0,
 - addressed - the device has a non-zero address but no configuration has
   been set,
 - configured - a set configuration succeeded.

The USB core may issue a port reset when a device is in any state, but the
Reset Device command will fail for a 0.96 xHC if the device is not in the
addressed or configured state.  Don't consider this failure as an error,
but don't free any endpoint rings if this command fails.

A storage driver may request that the USB device be reset during error
handling, so use GPF_NOIO instead of GPF_KERNEL while allocating memory
for the Reset Device command.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:12 -08:00
Sarah Sharp
6219c047d3 USB: xhci: Allow roothub ports to be disabled.
Add the hub emulation code to allow ports on an xHCI root hub to be
disabled.  Add the code to clear the port enabled/disabled bit, and clear
the port enabled/disabled change bit.  Like EHCI, the port cannot be
enabled by setting the port enabled/disabled bit.  Instead, a port is
enabled by the host controller after a reset.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:12 -08:00
Sarah Sharp
34fb562a43 USB: xhci: Refactor code to clear port change bits.
Refactor the code to clear the port change bits in the port status
register.  All port status change bits are write one to clear.

Remove a redundant port status read that was supposed to unblock any
posted writes.  We read the port after the write to get the updated status
for debugging, so the port read after that is unnecessary.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:11 -08:00
Sarah Sharp
b45b506911 USB: xhci: Refactor test for vendor-specific completion codes.
All commands that can be issued to the xHCI hardware can come back with
vendor-specific "informational" completion codes.  These are to be treated
like a successful completion code.  Refactor out the code to test for the
range of these codes and print debugging messages.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:10 -08:00
Sarah Sharp
a1d78c16bd USB: xhci: Allow allocation of commands without input contexts.
The xhci_command structure is the basic structure for issuing commands to
the xHCI hardware.  It contains a struct completion (so that the issuing
function can wait on the command), command status, and a input context
that is used to pass information to the hardware.  Not all commands need
the input context, so make it optional to allocate.  Allow
xhci_free_container_ctx() to be passed a NULL input context, to make
freeing the xhci_command structure simple.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:09 -08:00