platform_get_irq() may fail, so we should better check its return
value and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A debug printk statement was copied incorrectly into the new
csi1 parser code and causes a warning there:
drivers/media/platform/omap3isp/isp.c: In function 'isp_probe':
include/linux/dynamic_debug.h:134:3: error: 'i' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Since there is only one lane, the index is never set. This
changes the debug print to always print a zero instead,
keeping the original format of the message.
Fixes: 9211434bad30 ("media: omap3isp: Parse CSI1 configuration from the device tree")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix those warnings when building on i386:
drivers/media/platform/qcom/camss-8x16/camss-csiphy.c:333:22: warning: constant 1000000000000 is so big it is long long
drivers/media/platform/qcom/camss-8x16/camss-csiphy.c:339:32: warning: constant 1000000000000 is so big it is long long
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add abbreviations explanation at the top header blocks in source files.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use standard V4L2 control to get pixel clock rate from a sensor
linked in the media controller pipeline. Then calculate clock
rates on CSIPHY, CSID and VFE to use the lowest possible.
If the currnet pixel clock rate of the sensor cannot be read then
use the highest possible. This case covers also the CSID test
generator usage.
If VFE is already powered on by another pipeline, check that the
current VFE clock rate is high enough for the new pipeline.
If not return busy error code as VFE clock rate cannot be changed
while VFE is running.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add crop module configuration support to be able to apply cropping.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add scaler module configuration support to be able to apply scaling.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use VFE PIX input interface and do format conversion in VFE.
Supported input format is UYVY (single plane YUV 4:2:2) and
its different sample order variations.
Supported output formats are:
- NV12/NV21 (two plane YUV 4:2:0)
- NV16/NV61 (two plane YUV 4:2:2)
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add Makefile and update platform/Kconfig and platform/Makefile
to enable building of the QCom CAMSS driver.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files handle the video device nodes of the camss driver.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files control the VFE module. The VFE has different input
interfaces. The PIX input interface feeds the input data to an image
processing pipeline. Three RDI input interfaces bypass the image
processing pipeline. The VFE also contains the AXI bus interface which
writes the output data to memory.
RDI interfaces are supported in this version. PIX interface is not
supported.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files control the ISPIF module which handles the routing of the data
streams from the CSIDs to the inputs of the VFE.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files control the CSID modules which handle the protocol and
application layer of the CSI2 receivers.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files control the CSIPHY modules which are responsible for the
physical layer of the CSI2 receivers.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
videobuf_queue_ops are not supposed to change at runtime. All functions
working with videobuf_queue_ops provided by <media/videobuf-core.h> work
with const videobuf_queue_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This change the alignment restriction for output type of buffers
only, also set corect input resolution and fill bidirectional
vb2 queue flag in order to map output type buffers read/write.
The last is needed by encoder firmware to add padding at the
bottom of output (input buffers).
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implements g_/s_selection crop support by using DCMI crop
hardware feature.
User can first get the maximum supported resolution of the sensor
by calling g_selection(V4L2_SEL_TGT_CROP_BOUNDS).
Then user call to s_selection(V4L2_SEL_TGT_CROP) will reset sensor
to its maximum resolution and crop request is saved for later usage
in s_fmt().
Next call to s_fmt() will check if sensor can do frame size request
with crop request. If sensor supports only discrete frame sizes,
the frame size which is larger than user request is selected in
order to be able to match the crop request. Then s_fmt() resolution
user request is adjusted to match crop request resolution.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Test cookie return by dmaengine_submit() and return error if any.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
No one of the supported Venus version has implemented VP9 codec
for enconding, so drop it from the list of codecs.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the helper function in decoder and encoder find_format
to runtime check supported codecs.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds a helper function to runtime check supported encoder and
decoder codecs depending on venus version and platform.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fills missing (forgotten) video device name with
appropriate string so that udev can distinguishes between
decoder and encoder devices.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without PM support gcc could warns about unused functions, thus
mark runtime_suspend/resume as __maybe_unused.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the new CEC_CAP_DEFAULTS define in this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the new CEC_CAP_DEFAULTS define in this driver.
This also adds the CEC_CAP_RC capability which was missing here
(and this is also the reason for this new define, to avoid missing
such capabilities).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Only the first HDMI input has a CEC adapter, so just report 'HDMI 0' as
the HDMI input name.
For the HDMI outputs use bus_cnt instead of i as the output number.
The HDMI name now corresponds to what 'v4l2-ctl --list-outputs' reports.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support to emulate CEC pin monitoring. There are few hardware devices
that support this, so being able to emulate it here helps developing
software for this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The configuration of the pipeline and entities directly affects the
inputs required to each entity for the partition algorithm. Thus it
makes sense to involve those entities in the decision making process.
Extend the entity ops API to provide an optional .partition() operation.
This allows entities that affect the partition window to adapt the
window based on their configuration.
Entities implementing this operation must update the window parameter in
place, which will then be passed up the pipeline. This creates a process
whereby each entity describes what is required to satisfy the required
output to its predecessor in the pipeline.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide register definitions required for UDS phase and partition
algorithm support. The registers and bits defined here are available on
Gen3 hardware only.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we develop the partition algorithm, we need to store more information
per partition to describe the phase and other parameters.
To keep this data together, further abstract the existing v4l2_rect
into a partition specific structure. As partitions only have horizontal
coordinates, store the left and width values only.
When generating the partition windows, operate directly on the partition
struct rather than copying and duplicating the processed data
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The vsp1_pipe object context variables for div_size and
current_partition allowed state to be maintained through processing the
partitions during processing.
Now that the partition tables are calculated during stream on, there is
no requirement to store these variables in the pipe object.
Utilise local variables for the processing as required.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously the active window and partition sizes for each partition were
calculated for each partition every frame. This data is constant and
only needs to be calculated once at the start of the stream.
Extend the vsp1_pipe object to dynamically store the number of partitions
required and pre-calculate the partition sizes into this table.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Separate the code change from the function move so that code changes can
be clearly identified. This commit has no functional change.
The partition algorithm functions will be changed, and
vsp1_video_pipeline_setup_partitions() will call vsp1_video_partition().
To prepare for that, move the function without any code change.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Presently any received buffers are only released back to vb2 if
vsp1_video_stop_streaming() is called. If vsp1_video_start_streaming()
encounters an error, we will be warned by the vb2 handlers that buffers
have not been returned.
Move the buffer cleanup code to its own function to prevent duplication
and call from both vsp1_video_stop_streaming() and the error path in
vsp1_video_start_streaming().
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
platform_get_resource() may fail and in this case a NULL dereference
will occur.
Prevent this from happening by returning an error on
platform_get_resource() failure.
Fixes: b0444f18e0b18abce ("[media] coda: add i.MX6 VDOA driver")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Function of_clk_get() returns an ERR_PTR on failures. In file
mtk_mdp_commp.c, its return value is checked against NULL. Such checks
cannot prevent from accessing bad memory. This patch replaces the NULL
checks with IS_ERR checks.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
struct v4l2_subdev.host_priv is intended to be used by another driver. This
is hardly good design but back in the days of platform data was a quick
hack to get things done.
As the sub-device specific bus information can be stored to the ISP driver
specific struct allocated along with v4l2_async_subdev, keep the
information there and only there.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CSI PHY is associated with a CSI receiver. The code assumes this
receiver is a CSI2 module and relies on the CSI2 module object heavily to
access the ISP or pipeline objects. However, the receiver could also be a
CSI1/CCP2 module.
Pass a new CSI receiver entity pointer to the CSI PHY acquire function, and
replace all hardcoded usage of the CSI2 module with that CSI receiver
entity.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # on Beagleboard-xM + MPT9P031
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
