This patch (as811) removes some stale testing code from the root-hub
resume routine in ohci-hcd. It also adds a spin_lock_irq() call that
inadvertently got left out of an error pathway.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
replace open coded kmemdup() to save some screen space,
and allow inlining/not inlining to be triggered by gcc.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as808b) moves the Root Hub Status Change interrupt-disable
code in ohci-hcd back into the interrupt handler proper, to avoid the
chance of adverse interactions with mediocre hardware implementations.
It also deletes the root-hub status timer from within the interrupt-enable
routine. There's no need to poll for status any more once interrupts are
re-enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as806) fixes a compiler warning when ohci-hcd is built
with CONFIG_PM turned off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as804) makes USB driver matching ignore the interface
class, subclass, and protocol if the device class is Vendor Specific.
Drivers can override this policy by specifying a Vendor ID as part
of the match; then vendor-specific matches are allowed.
Linus Walleij has reported a problem this patch fixes. When a
particular mass-storage device is switched from mass-storage mode to
Media Transfer Protocol, the interface class remains set to mass-storage
and usb-storage binds to it erroneously, even though the device class
changes to Vendor-Specific.
This may cause a problem for some drivers until their match records can
be updated to include Vendor IDs. But if it does, then those records
were broken to begin with.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB HID driver doesn't include any code to handle a STALL on the
interrupt endpoint. While this may be uncommon, it does happen
sometimes. This patch (as805) adds a fix.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wireless USB Host Controllers accept a large number of devices per
host, which shows up as a large number of ports in its root hub.
When the number of ports in a hub device goes over 16, the activation
of the hub fails with the cryptic message in klogd.
hub 2-0:1.0: activate --> -22
Following this further, it was seen that:
hub_probe()
hub_configure()
generates pipe number
pseudo allocates buffer 'maxp' bytes in size using usb_maxpacket()
The endpoint descriptor for a root hub interrupt endpoint is
declared in
drivers/usb/core/hcd.c:hs_rh_config_descriptor and declares it
to be size two (supporting 15 devices max).
hub_activate()
usb_hcd_submit_urb()
rh_urb_enqueue()
urb->pipe is neither int nor ctl, so it errors out
rh_queue_status()
Returns -EINVAL because the buffer length is smaller
than the minimum needed to report all the hub port
bits as in accordance with USB2.0[11.12.3]. There has
to be trunc((PORTS + 1 + 7) / 8) bytes of space at
least.
Alan Stern confirmed that the reason for reading maxpktsize and not
the right amount is because some hubs are known to return more data
and thus cause overflow.
So this patch simply changes the code to make the interrupt endpoint's
max packet size be at least the minimum required by USB_MAXCHILDREN
(instead of a fixed magic number) and add documentation for that. This
way we are always ahead of the limit.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current Wireless USB host hardware (Intel i1480 for example) allows up
to 22 devices to connect, thus bringing up the max number of children
in the WUSB Host Controller to 22 'fake' ports. Upcoming hardware
might raise that limit.
Makes almost no difference to go to 31, as the bit arrays are
byte-aligned (plus an extra bit in general), so 22 bits fit in 4 bytes
as 31 do.
As well, the only other array that depends on USB_MAXCHILDREN is
'struct usb_hub->indicator'. By declaring it 'u8' instead of 'enum
hub_led_mode', we reduce the size of each entry from 4 bytes (in i386)
to 1, which will add as we when are doubling USB_MAXCHILDREN
(with 16 the size of that array is 64 bytes, with 31 would be 128; by
using u8 that goes down to 31 bytes).
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a bug. When checking for ati_remote->outbuf we free freeing
ati_remote->inbuf so we end up freeing ati_remote->inbuf twice.
Also the checks for 'ati_remote->inbuf != NULL' and 'ati_remote->outbuf !=
NULL' are redundant as usb_buffer_free() does this.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds support for HTC Smart Phones in modem mode (as opposed to sync
mode). Loads and works with pppd on my T-Mobile SDA.
Signed-off-by: Alex Sanks <alex@sanks.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_get_device_descriptor() used to convert several descriptor fields to host
CPU's byte order. Now that it doesn't convert them anymore, update the
documentation to reflect this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For some reason the unusual_devs.h entry for Sony Ericsson P990i had
three identical copies in a wrong place in the file in addition to the
correct entry.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new Core2 Duo MacBook Pro have a new keyboard+trackpad device.
The following patch adds the needed HID quirk for the Fn key.
Signed-off-by: Julien BLACHE <jb@jblache.org>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB Storage: this patch adds support for Sony Ericsson P990i
Signed-off-by: Jan Mate <mate@fiit.stuba.sk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
similar to the version in adbhid_input_register(): The '<>' key and the
'^°' key on a german keyboard is swapped. Provide correct keys to
userland, external USB keyboards will not work correctly when the
'badmap'/'goodmap' workarounds from xkeyboard-config are used.
It is expected that distributions drop the badmap/goodmap part from
keycodes/macintosh in the xkeyboard-config package.
This is probably 2.6.18.x material, if major distros settle on 2.6.18.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a suspended OHCI controller sees a port's status change, it sets
both the Root-Hub-Status-Change and the Resume-Detect bits in the
Interrupt Status register. Processing both these bits, the driver
tries to resume the root hub twice!
This patch (as807) fixes the bug by ignoring RD if RHSC is set. It
also prints a slightly more informative log message when a
remote-wakeup event occurs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recently this entry's bcd scope was narrowed so as not to falsly apply
to bcd's other than 0x0110. But while it breaks those of a larger bcd,
it is still needed for those of a smaller bcd - so this changes the
lower bcd limit to 0x0000.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Please add a usb pid to the ftdi_sio driver. The pid is used by dmx4all
dmx-interfaces (for stage lighting).
The interfaces are using the usb-id 0403:c850. I added the id to the driver
and it works perfectly. I added a patch for linux 2.6.18.1, too.
From: Frank Sievertsen <frank@sievertsen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds the vendor and prodcut id for a RFID construction kit from the
Elektor Electronics magazine, september 2006.
From: Kjell Myksvoll <kmyksvo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as822) prevents the OHCI autostop mechanism from kicking in
if the root hub is not able or not allowed to issue wakeup requests.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix mcs7830 patch
The recent mcs7830 update to make the MII support sharable goofed various
pre-existing configurations in two ways:
- it made the usbnet infrastructure reference MII symbols even
when they're not needed in the kernel being built
- it didn't enable MII along with the mcs7830 minidriver
This patch fixes these two problems.
However, there does seem to be a Kconfig reverse dependency bug in that MII
gets wrongly enabled in some cases (like USBNET=y and USBNET_MII=n); I think
I've noticed that same problem in other situations too. So the result can
mean kernels being bloated by stuff that's needlessly enabled ... better
than wrongly being disabled, but contributing to bloat.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB Storage: this patch adds support for Sony Ericsson P990i
Signed-off-by: Jan Mate <mate@fiit.stuba.sk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding additional USB vendor/product ID's for XBOX pads provided by the
XBOX Linux team.
Signed-off-by: Dominic Cerquetti <binary1230@yahoo.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove complaint from newer GCCs; they don't like forward function
declarations except in top-level contexts.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch add AIRcable USBto USB-HID blacklist, makes some little
changes things in the Kconfig to make AIRcable USB look as all the rest
of drivers. And it removes the readme part that was on
Documentation/usb/usb-serial.txt because it is not needed anymore.
Signed-off-by: Naranjo Manuel Francisco <naranjo.manuel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this has been confirmed to fix suspend problems with usblp.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if urb submission fails due to a transient error here eg. ENOMEM
, the driver is dead. This fixes it.
Regards
Oliver
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
use the endpoint address from the endpoint descriptor instead of the hardcoding
it to 0x81. at least some ITM based screen use a different address and don't work
without this.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Ralf Lehmann <ralf@lehmann.cc>
Cc: J.P. Delport <jpdelport@csir.co.za>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new version of sierra.c has introduced tables for the 1 port and 3
port variants. The device id i added in my last patch needs to be added
to the 3 port table.
Signed-off-by: Jan Luebbe <jluebbe@lasnet.de>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
3 new VID/PID combinations (registered with Silicon Laboratories Inc.)
added for devices made by Lipowsky Industrie Elektronik GmbH all using
the CP2102 usb-to-serial converter (Baby-JTAG, Baby-LIN, HARP-1).
Signed-off-by: Bjorn Schneider <schneider@lipowsky.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adam Kropelin had posted 32-bit fix in June 2005 about two weeks after I
originally had posted my fixes for big endian support. Adam has a UPS
device which reports LINEV using 32-bits.
Added comments to describe the limitations of the code.
extract() is the same version I posted earlier and tested in user space.
Made similar changes to implement() routine. I've written (and will
shortly post) a test for implement(). Code tested on C3600 (parisc) with
USB keyboard/mouse attached.
I've dropped test_implement.c and a few other user space test programs on
http://iou.parisc-linux.org/~grundler/tests/
-rw-r--r-- 1 grundler grundler 1750 Oct 18 09:13 test_extract.c
-rw-r--r-- 1 grundler grundler 561 Jan 25 2006 test_ffs.c
-rw-r--r-- 1 grundler users 7175 Apr 8 2005 test_fls.c
-rw-r--r-- 1 grundler grundler 206 Sep 1 15:52 test_gettimeofday.c
-rw-r--r-- 1 grundler grundler 1886 Oct 19 09:20 test_implement.c
-rw-r--r-- 1 grundler users 2707 Jun 4 2005 test_unaligned.c
I would appreciate if someone else would look at the output of
test_implement.c to make it does The Right Thing.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Dmitry Torokhov <dtor@mail.ru>
Acked-By: Adam Kropelin <akropel1@rochester.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The protocol in this entry is needed for some versions of the device but
not others. This adds the NEED_OVERRIDE flag to prevent it complaining
to users who don't need it.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
As reported by Peter Kucmeroski and Jason Ganovsky.
Cc: Peter Kucmeroski <PKucmeroski@novell.com>
Cc: Jason Ganovsky <JGanovsky@novell.com>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was apparently missed by the move to the generic IRQ code.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
