Add device-tree support for mt9m111 camera sensor.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 0ba2aeb6da increased the internal control ranges
to 64 bit, but that caused problems in drivers that use the minimum/maximum/step/default_value
control values in a division or modulus operations since not all architectures support
those natively.
Luckily, in almost all cases it is possible to just cast to 32 bits (the control value
is known to be 32 bits, so it is safe to cast). Only in v4l2-ctrls.c was it necessary to
use do_div in one function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The g_std and s_std operations are video-related, move them to the video
ops where they belong.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As discussed on the media summit 2013, there is no reason for the width
and height to be signed.
Therefore this patch is an attempt to convert those fields from __s32 to
__u32.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp)
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These aren't necessary after switch and while statements.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert the mt9m111 driver to asynchronous subdevice probing. Synchronous
probing is also still possible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The mt9t031 driver hasn't yet been updated to support asynchronous
subdevice probing. If such a probing is attempted, the driver is allowed
to fail, but it shouldn't Oops. This patch fixes such a potential NULL
pointer dereference.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Both synchronous and asynchronous imx074 subdevice probing is supported by
this patch.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of centrally enabling and disabling subdevice master clocks in
soc-camera core, let subdevice drivers do that themselves, using the
V4L2 clock API and soc-camera convenience wrappers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After the switch to devm_* functions, the 'remove' function does
not do anything. Delete it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After the switch to devm_* functions, the 'remove' function does
not do anything. Delete it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Silences the following warning:
WARNING: please, no space before tabs
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is no longer needed since the core now handles this through DBG_G_CHIP_INFO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Release v2.6.30 removed the MT9M001_PCA9536_SWITCH and
MT9V022_PCA9536_SWITCH Kconfig symbols, in commits
36034dc325 ("V4L/DVB (11032): mt9m001:
allow setting of bus width from board code") and
e958e27ade ("V4L/DVB (11033): mt9v022:
allow setting of bus width from board code").
These two commits removed all gpio related code from these two drivers.
But they skipped removing their two selects of GPIO_PCA953X. Remove
these now as they are outdated. Their dependencies can never evaluate to
true anyhow.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the issue that appears when mt9v024 camera is used with the
mt9v022 soc camera driver. The minimum total row time is 690 columns
(horizontal width + horizontal blanking). The minimum horizontal
blanking is 61. Thus, when the window width is set below 627, horizontal blanking must
be increased. For the mt9v024 camera the values above are correct and
for the mt9v022 camera the correct values are in the existing kernel driver.
Signed-off-by: Andrei Andreyanau <a.andreyanau@sam-solutions.net>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] soc-camera: Push probe-time power management to
drivers" causes an Oops during mt9m111 driver probing because its .ctx
private data field is now dereferenced before it is initialised. Fix this
by initialising the field earlier.
Reported-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit f9bd584365 changed V4L2_CID_EXPOSURE_AUTO
from boolean to enum, and commit af8425c54b
changed the creation of this control into a menu for the mt9m111. However,
mt9m111_set_autoexposure() is still interpreting the value set for this control
as a boolean, which also conflicts with the default value of this control set to
V4L2_EXPOSURE_AUTO (0).
This patch makes mt9m111_set_autoexposure() interpret the value set for
V4L2_CID_EXPOSURE_AUTO as defined by enum v4l2_exposure_auto_type.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original commit, adding the mt9t112 driver said, that mt9t111 and
mt9t112 had identical register layouts. This however doesn't seem to be
the case. At least pixel format selection in the mt9t111 datasheet is
different from the driver implementation. So far only the default YUYV
format has been verified to work with mt9t111. Limit the driver to only
report one supported format with mt9t111 until more formats are
implemented.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct soc_camera_link currently contains fields, used both by sensor and
bridge drivers. To make subdevice driver re-use simpler, split it into a
host and a subdevice parts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dereference to 'icl' should be moved below the NULL test.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* linus/master: (1428 commits)
futex: avoid wake_futex() for a PI futex_q
watchdog: using u64 in get_sample_period()
writeback: put unused inodes to LRU after writeback completion
mm: vmscan: check for fatal signals iff the process was throttled
Revert "mm: remove __GFP_NO_KSWAPD"
proc: check vma->vm_file before dereferencing
UAPI: strip the _UAPI prefix from header guards during header installation
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
jbd: Fix lock ordering bug in journal_unmap_buffer()
...
Set "y_skip_top" to zero and revise comment as I do not see this line
corruption on two different mt9v022 setups. The first read-out line
is perfectly fine. Add mt9v022 platform data configuring y_skip_top
for platforms that have issues with the first read-out line. Set
y_skip_top to 1 for pcm990 board.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some camera systems cannot operate mt9v022 in normal mode and use
only the snapshot mode. The TechNote for mt9v022 (TN0960) and mt9v024
(TN-09-225) describes required register settings when configuring the
snapshot operation. The snapshot mode requires that certain automatic
functions of the image sensor should be disabled or set to fixed values.
According to the TechNote bit 2 and bit 9 in the register 0x20 must be
set in snapshot mode and unset for normal operation. This applies for
mt9v022 Rev.3 and mt9v024. Add required reg. 0x20 settings dependent on
sensor chip version.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add controls for horizontal and vertical blanking. Also add an error
message for case that the control handler init failed. Since setting
the blanking registers is done by controls now, we shouldn't change
these registers outside of the control function. Use v4l2_ctrl_s_ctrl()
to set them.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the result of experimenting with the SpeedLink VAD Laplace webcam.
The register sequence for V4L2_MBUS_FMT_YUYV8_2X8 has been identified by
analyzing USB-logs of this device running on MS Windows.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the MT9V022_TOTAL_SHUTTER_WIDTH register is controlled in manual
mode by V4L2_CID_EXPOSURE control, it shouldn't be written directly in
mt9v022_s_crop(). In manual mode this register should be set to the
V4L2_CID_EXPOSURE control value. Changing this register directly and
outside of the actual control function means that the register value
is not in sync with the corresponding control value. Thus, the following
problem is observed:
- setting this control initially succeeds
- VIDIOC_S_CROP ioctl() overwrites the MT9V022_TOTAL_SHUTTER_WIDTH
register
- setting this control to the same value again doesn't
result in setting the register since the control value
was previously cached and doesn't differ
Remove MT9V022_TOTAL_SHUTTER_WIDTH register setting in mt9v022_s_crop()
and add a comment explaining why it is not needed in manual mode.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/i2c/soc_camera/ov2640.c:899:32: warning: variable 'win' set but not used [-Wunused-but-set-variable]
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We currently don't select the register bank in ov2640_s_ctrl, so we can end up
writing to DSP register 0x04 instead of sensor register 0x04.
This happens for example when calling ov2640_s_ctrl after ov2640_s_fmt.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_crop.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
make[4]: *** No rule to make target `drivers/media/platform/sh_mobile_csi2.c',
needed by `drivers/media/platform/sh_mobile_csi2.o'. Stop.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver for mt9v022 camera sensor is fully compatible for mt9v024 camera sensor
with the exception of several registers which have been changed addresses.
mt9v024 also has improved and additional features, but they are currently not in use.
Signed-off-by: Alex Gershgorin <alexg@meprolight.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sensor starts streaming video as soon as it gets powered or is
reset. Disable the output in the reset function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Conversion from i2c_client to ov772x_priv is only needed in a single
location, while conversion from v4l2_subdev to ov772x_priv is needed in
several locations. Perform the former manually, and use to_ov772x for
the later.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the requested format isn't supported, return a fixed default format
instead of the current format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The format and window size are only initialized during the first g_fmt
call. This leaves the device in an inconsistent state after
initialization, which will cause problems when implementing pad
operations. Move the format and window size initialization to probe
time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The control handler isn't freed if its initialization fails. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several client drivers access the hardware at probe time, for instance
to read the probe chip ID. Such chips need to be powered up when being
probed.
soc-camera handles this by powering chips up in the soc-camera probe
implementation. However, this will break with non soc-camera hosts that
don't perform the same operations.
Fix the problem by pushing the power up/down from the soc-camera core
down to individual drivers on a needs basis.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of forcing all soc-camera drivers to go through the mid-layer to
handle power management, create soc_camera_power_[on|off]() functions
that can be called from the subdev .s_power() operation to manage
regulators and platform-specific power handling. This allows non
soc-camera hosts to use soc-camera-aware clients.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[g.liakhovetski@gmx.de: fix compile breakage]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The remaining drivers are mostly platform drivers. Name the
dir to reflect it.
It makes sense to latter break it into a few other dirs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
