Elimintes prototype link event tracking functionality that has never
been fleshed out and doesn't do anything useful at the current time.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies the initial transfer of name table entries to a new neighboring
node so that the messages are enqueued as a unit, rather than individually.
The revised algorithm now locates the link carrying the message only once,
and eliminates unnecessary checks for link congestion, message fragmentation,
and message bundling that are not required when sending these messages.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances TIPC to ensure that a node that loses contact with a
neighboring node does not allow contact to be re-established until
it sees that its peer has also recognized the loss of contact.
Previously, nodes that were connected by two or more links could
encounter a situation in which node A would lose contact with node B
on all of its links, purge its name table of names published by B,
and then fail to repopulate those names once contact with B was restored.
This would happen because B was able to re-establish one or more links
so quickly that it never reached a point where it had no links to A --
meaning that B never saw a loss of contact with A, and consequently
didn't re-publish its names to A.
This problem is now prevented by enhancing the cleanup done by TIPC
following a loss of contact with a neighboring node to ensure that
node A ignores all messages sent by B until it receives a LINK_PROTOCOL
message that indicates B has lost contact with A, thereby preventing
the (re)establishment of links between the nodes. The loss of contact
is recognized when a RESET or ACTIVATE message is received that has
a "redundant link exists" field of 0, indicating that B's sending link
endpoint is in a reset state and that B has no other working links.
Additionally, TIPC now suppresses the sending of (most) link protocol
messages to a neighboring node while it is cleaning up after an earlier
loss of contact with that node. This stops the peer node from prematurely
activating its link endpoint, which would prevent TIPC from later
activating its own end. TIPC still allows outgoing RESET messages to
occur during cleanup, to avoid problems if its own node recognizes
the loss of contact first and tries to notify the peer of the situation.
Finally, TIPC now recognizes an impending loss of contact with a peer node
as soon as it receives a RESET message on a working link that is the
peer's only link to the node, and ensures that the link protocol
suppression mentioned above goes into effect right away -- that is,
even before its own link endpoints have failed. This is necessary to
ensure correct operation when there are redundant links between the nodes,
since otherwise TIPC would send an ACTIVATE message upon receiving a RESET
on its first link and only begin suppressing when a RESET on its second
link was received, instead of initiating suppression with the first RESET
message as it needs to.
Note: The reworked cleanup code also eliminates a check that prevented
a link endpoint's discovery object from responding to incoming messages
while stale name table entries are being purged. This check is now
unnecessary and would have slowed down re-establishment of communication
between the nodes in some situations.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates code in tipc_send_buf_fast() that handles messages
sent to a destination on the current node, since the only caller
of the routine only passes in messages destined for other nodes.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensure TIPC ignores an out-dated link reset message whose session
number predates the current session number. (Previously, TIPC only
ignored an out-date reset message whose session number was equal
to the current link session number.)
Out-dated link reset messages should not occur under normal circumstances;
however, they can be generated if a link endpoint is unable to send a
link reset message right away and queues it for later delivery, but the
queued message is not sent until after the link is established.
Thanks to Laser [gotolaser@gmail.com] for diagnosing the problem and
contributing a prototype patch.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Initializes the peer session number field of a newly created link
endpoint to an invalid value. This eliminates the remote possibility
that it will accidentally match the session number used by the peer
the first time the link is activated, and cause the link to ignore
a valid RESET message.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Sets the peer interface portion of the name of a newly created link
endpoint to "unknown". This ensures that state and statistics information
can be properly displayed during the time between the link endpoint's
creation and the time handshaking with its peer is completed.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes a test that ensures unicast link endpoints discard an incoming
message if it will not be consumed by the node itself and cannot be
forwarded to another node, since the preceding test already ensures that
the message is destined for this node and single-cluster TIPC no longer
performs message forwarding.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Performs cosmetic cleanup of the symbolic names used to specify TIPC
payload message header sizes. The revised names now more accurately
reflect the payload messages in which they can appear. In addition,
several places where these payload message symbol names were being used
to create non-payload messages have been updated to use the proper
internal message symbolic name.
No functional changes are introduced by this rework.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fixes a minor error in the title of one of the message size profiling
values printed as part of TIPC's link statistics.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Create a helper routine to enqueue a chain of sk_buffs to a link's
transmit queue. It improves readability and the new function is
anticipated to be used more than just once in the future as well.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Rework TIPC's message sending routines to take advantage of the total
amount of data value passed to it by the kernel socket infrastructure.
This change eliminates the need for TIPC to compute the size of outgoing
messages itself, as well as the check for an oversize message in
tipc_msg_build(). In addition, this change warrants an explanation:
- res = send_packet(NULL, sock, &my_msg, 0);
+ res = send_packet(NULL, sock, &my_msg, bytes_to_send);
Previously, the final argument to send_packet() was ignored (since the
amount of data being sent was recalculated by a lower-level routine)
and we could just pass in a dummy value (0). Now that the
recalculation is being eliminated, the argument value being passed to
send_packet() is significant and we have to supply the actual amount
of data we want to send.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies a TIPC send routine that did not discard the outgoing sk_buff
if it was not transmitted because of link congestion; this eliminates
the potential for buffer leakage in the many callers who did not clean up
the unsent buffer. (The two routines that previously did discard the unsent
buffer have been updated to eliminate their now-redundant clean up.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies the routine that fragments an existing message buffer to
use similar logic to that used when generating fragments from an iovec.
The routine now creates a complete chain of fragments and adds them to
the link transmit queue as a unit, so that the link sends all fragments
or none; this prevents the incomplete transmission of a fragmented
message that might otherwise result because of link congestion or
memory exhaustion. This change also ensures that the counter recording
the number of fragmented messages sent by the link is now incremented
only if the message is actually sent.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates code that restricts a link's counter of its fragmented
messages to a 16-bit value, since the counter value is automatically
restricted to this range when it is written into the message header.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates code that sets the link selector field in the header of
fragmented messages, since this information is never referenced.
(The unnecessary initialization was harmless as it was over-written
by the fragmented message identifier value before the fragments were
transmitted.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates a routine that is used in handling messages arriving from
another cluster or zone. Such messages can no longer be received by TIPC
now that multi-cluster and multi-zone network support has been eliminated.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of all remaining code relating to ROUTE_DISTRIBUTOR messages.
These messages were only used in multi-cluster and multi-zone networks,
which TIPC no longer supports. (For safety, TIPC now treats such messages
the same way that it handles other unrecognized messages.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances link creation code as follows:
1) Detects illegal attempts to add a requested link earlier in the
link creation process. This prevents TIPC from wasting time
initializing a link object it then throws away, and also eliminates
the code needed to do the throwing away.
2) Passes in the node object associated with the requested link.
This allows TIPC to eliminate a search to locate the node object,
as well as code that attempted to create the node if it doesn't
exist.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensures that the "redundant link exists" field of the LINK_PROTOCOL
messages sent by a link endpoint is set if and only if the sending
node has at least one other working link to the peer node. Previously,
the bit was set only if there were at least 2 working links to the peer
node, meaning the bit was incorrectly left unset in messages sent by a
non-working link endpoint when exactly one alternate working link was
available. The revised code now takes the state of the link sending
the message into account when deciding if an alternate link exists.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
All the other boolean like msg_set_X(m) operations don't
export both a msg_set_X(a) and a msg_clear_X(m), but instead
just have the single msg_set_X(m, val) variant.
Make the redundant_link one consistent by having the set take
a value, and delete the msg_clear_redundant_link() anomoly.
This is a cosmetic change and should not change behaviour.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Function names like "tipc_node_has_redundant_links" are unweildy
and result in long lines even for simple lines. The "has" doesn't
contribute any value add, so dropping that is a slight step in the
right direction. This is a cosmetic change, basic result of:
for i in `grep -l tipc_node_has_ *` ; do sed -i s/tipc_node_has_/tipc_node_/ $i ; done
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes support for the timestamp field of TIPC's link protocol messages.
This field was previously used to hold an OS-dependent timestamp value
that was used to assist in debugging early versions of TIPC. The field
has now been deemed unnecessary and has been removed from the latest TIPC
specification. This change has no impact on the operation of TIPC since
the field was set by TIPC, but never referenced.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensure that the routine that starts up processing on a newly created
link endpoint takes the spinlock of the node object that owns the link,
to prevent possible conflicts with processing involving other links
owned by that node object.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensures that a link reset or activate message has a "probe" field
of zero. (This field is currently unused in these messages, but this
could potentially change in future versions of TIPC.)
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances TIPC's unicast and broadcast link code to update the transmit
queue maximum size counter in a single place, namely the routine that
adds messages to the queue. This ensures that the maximum size statistic
reported for unicast links is completely accurate, rather than being
partially based on statistical sampling.
The changes to link.h are just documenting the roles of the variables.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allows the broadcast link to track the node that is requesting a retransmit
in a new field dedicated to that purpose. This replaces the existing
mechanism that (ab)uses an existing node structure linked list field to do
the tracking.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Corrects print statements that use %x to print pointer values to use
%p instead, so that 64-bit pointer values are displayed correctly.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances TIPC link code to ignore an invalid link tolerance value
contained in an incoming LINK_PROTOCOL message, rather than
processing the value and potentially causing a divide-by-zero error.
Also add a compile-time check that catches attempts to redefine
TIPC's minimum link tolerance value in a manner that might result
in the same divide-by-zero error at run-time.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Combines two distinct structures containing information about a TIPC bearer
into a single structure. The structures were previously kept separate so
that public information about a bearer could be made available to plug-in
media types using TIPC's native API, while the remaining information was
kept private for use by TIPC itself. However, now that the native API has
been removed there is no longer any need for this arrangement.
Since one of the structures was already embedded within the other, the
change largely involves replacing instances of "publ.foo" with "foo".
The changes do not otherwise alter the operation of TIPC bearers.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Merge two distinct structures containing information about a TIPC port
into a single structure. The structures were previously kept separate
so that public information about a port could be made available to
applications using TIPC's native API, while the remaining information
was kept private for use by TIPC itself. However, now that the native
API has been removed there is no longer any need for this somewhat
confusing arrangement.
Since one of the structures was already embedded within the other, the
change largely involves replacing instances of "publ.foo" with "foo".
The changes do not otherwise alter the operation of TIPC ports.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cleans up TIPC's source code to eliminate the presence of unnecessary
use of {} around single statements.
These changes are purely cosmetic and do not alter the operation of TIPC
in any way.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleans up TIPC's source code to eliminate assigning values to variables
within conditional expressions, improving code readability and reducing
warnings from various code checker tools.
These changes are purely cosmetic and do not alter the operation of TIPC
in any way.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleans up TIPC's source code to eliminate deviations from generally
accepted coding conventions relating to leading/trailing white space
and white space around commas, braces, cases, and sizeof.
These changes are purely cosmetic and do not alter the operation of TIPC
in any way.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminates most link-specific debugging code in TIPC, which is now
largely unnecessary. All calls to the link-specific debugging macros
have been removed, as are the macros themselves; in addition, the optional
allocation of print buffers to hold debugging information for each link
endpoint has been removed. The ability for TIPC to print out helpful
diagnostic information when link retransmit failures occur has been
retained for the time being, as an aid in tracking down the cause of
such failures.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminates obsolete calls to two of TIPC's main debugging macros, as well
as a pair of associated debugging routines that are no longer required.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminates routines and data structures that were intended to allow
TIPC to route messages to other clusters. Currently, TIPC supports only
networks consisting of a single cluster within a single zone, so this
code is unnecessary.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes a symbol that is not referenced anywhere by TIPC's link code.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gets rid of #include statements that are no longer required as a
result of the merging of obsolete native API header file content
into other TIPC include files.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do some cleanups of TIPC based on make namespacecheck
1. Don't export unused symbols
2. Eliminate dead code
3. Make functions and variables local
4. Rename buf_acquire to tipc_buf_acquire since it is used in several files
Compile tested only.
This make break out of tree kernel modules that depend on TIPC routines.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all instances of legacy, or as yet to be implemented code
that is currently living within an #if 0 ... #endif block.
In the rare instance that some of it be needed in the future,
it can still be dragged out of history, but there is no need
for it to sit in mainline.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that TIPC does not re-establish communication with a
neighboring node until it has finished updating all data structures
containing information about that node to reflect the earlier loss of
contact. Previously, it was possible for TIPC to perform its purge of
name table entries relating to the node once contact had already been
re-established, resulting in the unwanted removal of valid name table
entries.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a check to tipc_recv_msg() to ensure it discards messages
arriving on a newly disabled bearer. This is needed to deal with a
race condition that can arise if the bearer is in the midst of being
disabled when it receives a message. Performing the check after
tipc_net_lock has been taken ensures that TIPC's bearers are in a
stable state while the message is being processed.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions have enough code in them such that they
seem like sensible targets for un-inlining. Prior to doing
that, this adds the tipc_ prefix to the functions, so that
in the event of a panic dump or similar, the subsystem from
which the functions come from is immediately clear.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than live in link.c where they can only be used in that file alone,
these helper routines are better served by being in link.h
Relocated are the following:
link_working_working
link_working_unknown
link_reset_unknown
link_reset_reset
link_blocked
link_congested
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a straight return of a field; there is no
value in the abstraction of hiding it behind a function.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate an argument in a print statement that has no corresponding
format specification.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate a field of the TIPC port structure that is populated,
but never referenced.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
