Commit Graph

44 Commits

Author SHA1 Message Date
Bartlomiej Zolnierkiewicz
85ad93ad56 ide: set drive->autotune in ide_pci_setup_ports()
Majority of host drivers using IDE PCI layer set drive->autotune, the only
exceptions are:

generic.c
ns87415.c
rz1000.c
trm290.c
* no ->set_pio_mode method

it821x.c:
* if memory allocation fails drive->autotune won't be set
  (but there also won't be ->set_pio_mode method in such case)

piix.c:
* MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method)

However if there is no ->set_pio_mode method there are no changes in behavior
w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-19 00:30:12 +02:00
Bartlomiej Zolnierkiewicz
93c6807985 alim15x3: always tune PIO
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-19 00:30:11 +02:00
Bartlomiej Zolnierkiewicz
5f8b6c3485 ide: add ->mwdma_mask and ->swdma_mask to ide_pci_device_t (take 2)
* Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t.

* Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in
  setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif
  method may still override them).

* Convert IDE PCI host drivers to use ide_pci_device_t DMA masks.

While at it:

* Use ATA_{UDMA,MWDMA,SWDMA}* defines.

* hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345.

* serverworks.c: fix DMA masks being set before checking DMA base.

v2:
* Add missing masks to DECLARE_GENERIC_PCI_DEV() macro.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-19 00:30:07 +02:00
Bartlomiej Zolnierkiewicz
238e4f142c ide: add IDE_HFLAG_NO_LBA48 and IDE_HFLAG_NO_LBA48_DMA host flags
Add IDE_HFLAG_NO_LBA48[_DMA] host flags, use it instead of hwif->no_lba48[_dma]
and then remove no longer needed hwif->no_lba48[_dma].  As a side-effect
this change fixes hwif->no_lba48_dma not being restored by ide_hwif_restore().

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-19 00:30:07 +02:00
Bartlomiej Zolnierkiewicz
47b687882c ide: add IDE_HFLAG_NO_{DMA,AUTODMA} host flags
Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags.  Convert all host drivers using
ide_pci_device_t to use these flags instead of d->autodma and then remove no
longer needed d->autodma.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-19 00:30:06 +02:00
Bartlomiej Zolnierkiewicz
7cab14a799 ide: add IDE_HFLAG_BOOTABLE host flag
Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define.  Convert
all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD}
instead of d->bootable and then remove no longer needed d->bootable.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-19 00:30:06 +02:00
Bartlomiej Zolnierkiewicz
33c1002ed9 ide: add IDE_HFLAG_NO_ATAPI_DMA host flag
Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA.  Then remove no longer needed hwif->atapi_dma.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-19 00:30:06 +02:00
Bartlomiej Zolnierkiewicz
9ff6f72f43 ide: remove hwif->autodma and drive->autodma
* hpt34x.c: disable DMA masks for HPT345
  (hwif->autodma is zero so DMA won't be enabled anyway).

* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
  (hwif->autodma is zero so DMA won't be enabled anyway).

* Check noautodma global variable instead of drive->autodma in ide_tune_dma().

  This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
  au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.

* Remove hwif->autodma (it was not checked by IDE core code anyway) and
  drive->autodma (was set by all host drivers - except HPT345/TRM290 special
  cases - unless "ide=nodma" was used).

While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
  (this setting was always later over-ridden by host drivers anyway)

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-16 22:29:58 +02:00
Bartlomiej Zolnierkiewicz
9cbcc5e3c5 ide: use PCI_VDEVICE() macro
While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-16 22:29:56 +02:00
Bartlomiej Zolnierkiewicz
0ae2e17865 ide: remove ->ide_dma_check (take 2)
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
  on BIOS for programming device/controller for DMA.  Set it in cy82c693,
  generic, ns87415, opti621 and trm290 host drivers.

* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA.  Set it in cs5520
  host driver.

* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.

* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
  implementations.  Fix all places checking for presence of ->ide_dma_check
  hook to check for ->ide_dma_on instead.

* Remove no longer needed code from config_drive_for_dma().

* Make ide_tune_dma() static.

v2:
* Fix config_drive_for_dma() return values.

* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
  dummy config_drive_for_dma() inline.

* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().

* Fix init_hwif_it8213() comment.

There should be no functionality changes caused by this patch.

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-16 22:29:55 +02:00
Bartlomiej Zolnierkiewicz
d3b90baf09 ide: remove drive->init_speed zeroing
Several host drivers used to reset drive->init_speed in their ->ide_dma_check
implementations which resulted in incorrect init speed being reported to the
user, fix it.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-16 22:29:54 +02:00
Bartlomiej Zolnierkiewicz
99149a4859 alim15x3: remove redundant m5229_revision check
init_dma_ali15x3() guarantees that hwif->dma_base will never be set for
m5229_revision < 0x20 so remove redundant m5229_revision >= 0x20 check from
init_hwif_common_ali15x3().

While at it remove incorrect comment.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-13 17:47:53 +02:00
Bartlomiej Zolnierkiewicz
88b2b32bab ide: move ide_config_drive_speed() calls to upper layers (take 2)
* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.

* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program 
  the host for the transfer mode after programming the device.  Set it
  in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
  and via82cxxx host drivers.

* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
  skip programming of host/device for the transfer mode ("smart" hosts).
  Set it in it821x host driver and check it in ide_tune_dma().

* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
  direct ->set_pio_mode/->speedproc users to use these helpers.

* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
  methods to callers.

* Rename ->speedproc method to ->set_dma_mode, make it void and update
  all implementations accordingly.

* Update ide_set_xfer_rate() comments.

* Unexport ide_config_drive_speed().

v2:
* Fix issues noticed by Sergei:
  - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
    to setting DMA modes from sc1200_set_pio_mode() to do_special()
  - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
  - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
  - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
  - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
  - don't set ->set_{pio,dma}_mode on it821x in "smart" mode
  - fix build problem in pmac.c
  - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
  - improve patch description

Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
  PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
  the device (not really an issue since 0x00 is not supported correctly by
  any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-13 17:47:51 +02:00
Linus Torvalds
19f71153b9 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (24 commits)
  ide: use only ->set_pio_mode method for programming PIO modes (take 2)
  sis5513: don't change UDMA settings when programming PIO
  it8213/piix/slc90e66: don't change DMA settings when programming PIO
  alim15x3: PIO mode setup fixes
  siimage: fix ->set_pio_mode method to select PIO data transfer
  cs5520: don't enable VDMA in ->speedproc
  sc1200: remove redundant warning message from sc1200_tune_chipset()
  ide-pmac: PIO mode setup fixes (take 3)
  icside: fix ->speedproc to return on unsupported modes (take 5)
  sgiioc4: use ide_tune_dma()
  amd74xx/via82cxxx: use ide_tune_dma()
  ide: add ide_set{_max}_pio() (take 4)
  ide: Kconfig face-lift
  ide: move ide_rate_filter() calls to the upper layer (take 2)
  sis5513: add ->udma_filter method for chipset_family >= ATA_133
  ide: mode limiting fixes for user requested speed changes
  ide: add missing ide_rate_filter() calls to ->speedproc()-s
  ide: call udma_filter() before resorting to the UltraDMA mask
  ide: make jmicron match vendor and device class
  pdc202xx_new: switch to using pci_get_slot() (take 2)
  ...
2007-10-11 19:20:44 -07:00
Bartlomiej Zolnierkiewicz
8f4dd2e426 ide: use only ->set_pio_mode method for programming PIO modes (take 2)
Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.

v2:
* Fix pmac_ide_tune_chipset() comment.

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-11 23:54:02 +02:00
Bartlomiej Zolnierkiewicz
a6fe837ed6 alim15x3: PIO mode setup fixes
* Return failure in ->speedproc method for unsupported/invalid transfer
  modes passed from user-space (fixes theoretical OOPS in ali_tune_pio()
  and/or setting random PIO timings on host controller + disabling UDMA
  bit + setting unsupported/invalid transfer mode on the device).

* Don't disable UDMA bit when programming PIO modes.

* Add FIXME about DMA timings never being set.

* Bump driver version.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-11 23:54:01 +02:00
Bartlomiej Zolnierkiewicz
26bcb879c0 ide: add ide_set{_max}_pio() (take 4)
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
  and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.

* Add set_pio_mode_abuse() for checking if host driver has a non-standard
  ->tuneproc() implementation and use it in do_special().

* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
  the maximum PIO mode supported by the host), also add ide_set_max_pio()
  wrapper for ide_set_pio() to use for auto-tuning.  Convert users of
  ->tuneproc to use ide_set{_max}_pio() where possible.  This leaves only
  do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
  a direct users of ->tuneproc.

* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
  reporting PIO mode selected from ->tuneproc implementations.

* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.

* Remove stale comment from ide_config_drive_speed().

v2:
* Fix "ata_" prefix (Noticed by Jeff).

v3:
* Minor cleanups/fixups per Sergei's suggestions.

v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
  (Noticed by Andrew Morton).

* Improve some ->set_pio_mode comments.

Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-11 23:54:00 +02:00
Bartlomiej Zolnierkiewicz
f212ff28f0 ide: move ide_rate_filter() calls to the upper layer (take 2)
* Move ide_rate_filter() calls from host drivers to IDE core.

* Make ide_rate_filter() static.

* Make 'speed' argument of ->speedproc const.

v2:
* Fix it8213_tune_chipset() comment.

There should be no functionality changes caused by this patch.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-11 23:53:59 +02:00
Jeff Garzik
1855256c49 drivers/firmware: const-ify DMI API and internals
Three main sets of changes:

1) dmi_get_system_info() return value should have been marked const,
   since callers should not be changing that data.

2) const-ify DMI internals, since DMI firmware tables should,
   whenever possible, be marked const to ensure we never ever write to
   that data area.

3) const-ify DMI API, to enable marking tables const where possible
   in low-level drivers.

And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.

The bulk of the changes are #2 and #3, which are interrelated.  #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-09 20:22:20 -04:00
Daniel Exner
03e6f489b3 pata_ali/alim15x3: override 80-wire cable detection for Toshiba S1800-814
Add Toshiba S1800-814 to whitelist for both pata_ali and alim15x3,
as it is correctly detected as 40-wire connected but this cable is
short enough to still use transfer modes higher than UDMA33.

Signed-off-by: Daniel Exner <dex@dragonslave.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-09-11 22:28:36 +02:00
Bartlomiej Zolnierkiewicz
8663fd6d0d alim15x3: Correct HP detect
Direct port of Alan's fix for pata_ali.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-01 23:46:43 +02:00
Bartlomiej Zolnierkiewicz
4099d14322 ide: add PIO masks
* Add ATA_PIO[0-6] defines to <linux/ata.h>.

* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.

* Add PIO masks to host drivers.

<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:59 +02:00
Bartlomiej Zolnierkiewicz
2134758d2a ide: drop "PIO data" argument from ide_get_best_pio_mode()
* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
  and convert all users accordingly.

* Remove no longer needed ide_pio_data_t.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:58 +02:00
Bartlomiej Zolnierkiewicz
a5d8c5c834 ide: add ide_pci_device_t.host_flags (take 2)
* Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags
  and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS.

* Add IDE_HFLAG_SINGLE flag for single channel devices.

* Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE
  and remove no longer needed ide_pci_device_t.channels field.

v2:
* Fix issues noticed by Sergei:
  - correct code alignment in scc_pata.c
  - s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:55 +02:00
Auke Kok
44c10138fd PCI: Change all drivers to use pci_device->revision
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.

This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.

In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.

Compile tested with make all{yes,mod}config on x86_64 and i386.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-11 16:02:10 -07:00
Bartlomiej Zolnierkiewicz
95ba8c17bc alim15x3: backport short cables support from pata_ali.c
Backport short cables support from pata_ali.c and while at it cleanup
existing cable detection code.

This patch should allow UDMA > 2 modes on HP Pavilion N5430 and Fujitsu P2000.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
2007-07-09 23:17:58 +02:00
Bartlomiej Zolnierkiewicz
49521f97cc ide: add short cables support
This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter.  Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.

Next patches add automatic detection of some systems using short cables.

Changes:

* Rename hwif->udma_four to hwif->cbl and make it u8.

* Convert all existing users accordingly (use ATA_CBL_* defines while at it).  

* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().

* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
2007-07-09 23:17:58 +02:00
Bartlomiej Zolnierkiewicz
38ff8a74e8 alim15x3: use ide_tune_dma()
Use ide_tune_dma() in ali15x3_config_drive_for_dma() and remove all the open
coded DMA tuning code and also config_chipset_for_dma().  Set ->atapi_dma flag
correctly in init_hwif_common_ali15x3() so ide_tune_dma() can take care of
checking if ATAPI DMA is allowed and remove open coded ATAPI DMA check from
ali15x3_config_drive_for_dma().

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:43 +02:00
Bartlomiej Zolnierkiewicz
ecfd80e4a5 ide: make /proc/ide/ optional
All important information/features should be already available through
sysfs and ioctl interfaces.

Add CONFIG_IDE_PROC_FS (CONFIG_SCSI_PROC_FS rip-off) config option,
disabling it makes IDE driver ~5 kB smaller (on x86-32).

While at it add CONFIG_PROC_FS=n versions of proc_ide_{create,destroy}()
and remove no longer needed #ifdefs.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:09 +02:00
Bartlomiej Zolnierkiewicz
2d5eaa6dd7 ide: rework the code for selecting the best DMA transfer mode (v3)
Depends on the "ide: fix UDMA/MWDMA/SWDMA masks" patch.

* add ide_hwif_t.udma_filter hook for filtering UDMA mask
  (use it in alim15x3, hpt366, siimage and serverworks drivers)
* add ide_max_dma_mode() for finding best DMA mode for the device
  (loosely based on some older libata-core.c code)
* convert ide_dma_speed() users to use ide_max_dma_mode()
* make ide_rate_filter() take "ide_drive_t *drive" as an argument instead
  of "u8 mode" and teach it to how to use UDMA mask to do filtering
* use ide_rate_filter() in hpt366 driver
* remove no longer needed ide_dma_speed() and *_ratemask()
* unexport eighty_ninty_three()

v2:
* rename ->filter_udma_mask to ->udma_filter
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

v3:
* updated for scc_pata driver (fixes XFER_UDMA_6 filtering for user-space
  originated transfer mode change requests when 100MHz clock is used)

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:08 +02:00
Bartlomiej Zolnierkiewicz
1813720723 ide: fix UDMA/MWDMA/SWDMA masks (v3)
* use 0x00 instead of 0x80 to disable ->{ultra,mwdma,swdma}_mask
* add udma_mask field to ide_pci_device_t and use it to initialize
  ->ultra_mask in aec62xx, cmd64x, pdc202xx_{new,old} and piix drivers
* fix UDMA masks to match with chipset specific *_ratemask()
  (alim15x3, hpt366, serverworks and siimage drivers need UDMA mask
   filtering method - done in the next patch)

v2:
* piix: fix cable detection for 82801AA_1 and 82372FB_1
  [ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* cmd64x: use hwif->cds->udma_mask
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* aec62xx: fix newly introduced bug - check DMA status not command register
  [ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

v3:
* piix: use hwif->cds->udma_mask
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:07 +02:00
Bartlomiej Zolnierkiewicz
072cdcbb7a alim15x3: PIO fallback fix
If DMA tuning fails always set the best PIO mode.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:50 +02:00
Sergei Shtylyov
21b8247713 alim15x3: fix PIO mode setup
The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to ali15x3_tune_pio() and "wrapping" the new tuneproc()
method around it and making it return the mode set, update the heading comment.

Also, setting PIO mode via the speedproc() method does not work due to passing 
to the tuneproc() method's a mode number not biased by XFER_PIO_0 -- fix this
along with a typo in the heading comment...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-03-03 17:48:52 +01:00
Bartlomiej Zolnierkiewicz
3608b5d71a ide: add ide_set_dma() helper (v2)
* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
  -1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
   0 when DMA needs to be enabled  (== need to call ->ide_dma_on)
   1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly

v2:
* updated for scc_pata

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-02-17 02:40:26 +01:00
Bartlomiej Zolnierkiewicz
0ecdca26e5 ide: use PIO/MMIO operations directly where possible (v2)
This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.

v2:
* updated for scc_pata

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-02-17 02:40:25 +01:00
Bartlomiej Zolnierkiewicz
82ab1eeceb ide: add missing __init tags to IDE PCI host drivers
also change __devinit tag for sgiioc4.c:ioc4_ide_init() to __init

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-01-27 13:46:56 +01:00
Alan Cox
b148900996 [PATCH] ide: more conversion to pci_get APIs
This completes IDE except for one use which requires a new core PCI function
and will be polished up at the end

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:03 -08:00
Michael De Backer
e11db063d8 [PATCH] alim15x3.c: M5229 (rev c8) support for DMA cd-writer
Configuration bits are not set properly for DMA on some chipset revisions.
It has already been corrected for M5229 (rev c7) but not for M5229 (rev
c8).  This leads to the bug described at
http://bugzilla.kernel.org/show_bug.cgi?id=5786 (lost interrupt + ide bus
hangs).

Signed-off-by: Michael De Backer <micdb@skynet.be>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-13 07:32:14 -07:00
Jörn Engel
6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
KAI.HSU
0d8a95efd8 [PATCH] alim15x3: ULI M-1573 south Bridge support
From http://bugzilla.kernel.org/show_bug.cgi?id=6358

The alim15x3.c havn't been update for 3 years.  Recently when we use this
"ULI M1573" south bridge chip found that can't mount CDROM(VCD) smoothly,
must waiting for a long time.  After I check the "ULI M1573" south bridge
datasheet, I found the reason.  The reason is the "ULI M1573" version in
the Linux is "0xC7" not "0xC4" anymore So I was modified the source than it
was successed.

Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-19 09:13:53 -07:00
Alexey Dobriyan
2fefef1828 [PATCH] alim15x3: use KERN_WARNING
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2005-11-18 22:22:21 +01:00
Hanna Linder
cc3f7ca51a [PATCH] alim15x3: replace pci_find_device() with pci_dev_present()
From: Hanna Linder <hannal@us.ibm.com>

The dev returned from pci_find_device() was not used so it can be
replaced with pci_dev_present().  Compile tested.

Signed-off-by: Hanna Linder <hannal@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2005-11-18 22:19:15 +01:00
Herbert Xu
c2f12589bf [PATCH] ide: hotplug mark __devinit alim15x3.c
From: Herbert Xu <herbert@gondor.apana.org.au>

mark the __init section __devinit.
Splitted up from the Debian kernel patch.

see the thread about the pci hotplug crash on a stratus box.
http://marc.theaimsgroup.com/?l=linux-kernel&m=111930108613386&w=2

Signed-off-by: maximilian attems <janitor@sternwelten.at>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
2005-07-03 16:06:13 +02:00
Linus Torvalds
1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00