and put all uio related structures and ring buffers in it. This allows
uio operations to be done independent of the cnic device structures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2x devices require a 2 second quiet time before sending the last
RAMROD command to destroy a connection. This sleep wait adds up to a
long delay when iscsid is serially destroying maultiple connections.
Create a workqueue to perform the final connection cleanup in the
background to speed up the process. This significantly speeds up the
process as the wait time can be done in parallel for multiple connections.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactoring code for the next patch to defer connection clean up.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so that we can additional bit definitions without requiring a spinlock.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to reduce some duplicate code. Also, use tasklet_kill() in
cnic_free_irq() to wait for the cnic_irq_task to complete.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent unnecessary error message. pci_save_state() is also moved to
the end of ->probe() so that all PCI config, including AER state, will be
saved.
Update version to 2.0.18.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Improved flow control and simplified interface
- Use hardware RSS indirection table instead of the slower firmware-
based table
- Lower latency interrupt on 5709
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that pch_gbe_xmit_frame uses skb after it is freed. Fix
that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Masayuki Ohtake <masa-korg@dsn.okisemi.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that i2400m_rx frees skb, but still uses skb->len even
though it has skb_len defined. So use skb_len properly in the code.
And also define it unsinged int rather than size_t to solve
compilation warnings.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: linux-wimax@intel.com
Acked-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with hardware slow in negotiation, the system did freeze
while trying to mount root on nfs at boot time.
the link state has not been initialised so network stack
tried to start transmission right away. this caused instant
retries, as the driver solely stated business upon link down,
rendering the system unusable.
notify carrier off initially to prevent transmission until
phylib will report link up.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test whether index exceeds fw->size before reading the element
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
sundance get_stats() should not be run concurrently, add a lock to avoid
potential losses.
Note: Remove unused rx_lock field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify: ((a && b) || (!a && !b)) => (a == b)
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DMA API as PCI equivalents will be deprecated. This change also
allow to allocate with GFP_KERNEL where possible.
Tested-by: Neal Becker <ndbecker2@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have fedora bug report where driver fail to initialize after
suspend/resume because of memory allocation errors:
https://bugzilla.redhat.com/show_bug.cgi?id=629158
To fix use GFP_KERNEL allocation where possible.
Tested-by: Neal Becker <ndbecker2@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just rename all P3 #define to P3P.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Allow promiscous mode setting for VF's depending upon the configuration.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove "Flex-10" from board description.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRO was not getting enable after interface down/up.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put device in quiescent mode during internal loopback test.
Before running test, set state to NEED_QUISCENT. After getting
ack from all function, change state to QUISCENT and perform test.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently fw recovery usage global workqueue.
As same workqueue used by kernel for ethtool and etc., supporting
quiescent mode is not possible, without driver private workqueue.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The filter engine will time-out and ignore filters beyond
200-something hops. We also need to avoid infinite loops in
efx_filter_search() when the table is full.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit removed DISABLE_REGWRITE_BUFFER ops. The unnecessary
REGWRITE_BUFFER_FLUSH was not removed properly which is causing failure on
hw reset.
Author: Felix Fietkau <nbd@openwrt.org>
Date: Tue Oct 5 12:03:42 2010 +0200
ath9k_hw: clean up register write buffering
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the NVS/INI-parameters for the driver/firmware there is the FEM
(front end module) selection option, which may configure the hardware FEM
via autodetection or manual selection. So far, there has been support for
manual selection only.
Add support for FEM autodetection.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 030725d2c7c1fafec7ede618647bf30ed79601f0.
This commit relies on commit 5ed3bc7288487bd4f891f420a07319e0b538b4fe
("mac80211: use netif_receive_skb in ieee80211_tx_status callpath")
Unfortunately not all drivers are calling ieee80211_tx_status from a
compatible context, so that commit needs to be reverted in 2.6.36.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the new infrastructure to balance interrupts for flow
alignment when ATR or Flow Director are enabled.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver does not compile on s390:
drivers/net/stmmac/stmmac_main.c: In function 'stmmac_adjust_link':
drivers/net/stmmac/stmmac_main.c:210: error: implicit declaration of function 'readl'
drivers/net/stmmac/stmmac_main.c:263: error: implicit declaration of function 'writel'
drivers/net/stmmac/stmmac_main.c: In function 'stmmac_dvr_probe':
drivers/net/stmmac/stmmac_main.c:1674: error: implicit declaration of function 'ioremap'
drivers/net/stmmac/stmmac_main.c:1674: warning: assignment makes pointer from integer without a cast
drivers/net/stmmac/stmmac_main.c:1761: error: implicit declaration of function 'iounmap'
make[3]: *** [drivers/net/stmmac/stmmac_main.o] Error 1
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Giuseppe CAVALLARO <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Effect:
Slave Interface: eth5
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: XX:XX:XX:XX:XX:XX
Slave queue ID: 0
Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface was enslaved when it was down, bonding thinks
it has speed -1 even after it goes up. This leads into selecting
a wrong active interface in active/backup mode on mixed 10G/1G or
1G/100M environment.
before:
bonding: bond0: link status definitely up for interface eth5, 100 Mbps full duplex.
bonding: bond0: link status definitely up for interface eth0, 100 Mbps full duplex.
after:
bonding: bond0: link status definitely up for interface eth5, 10000 Mbps full duplex.
bonding: bond0: link status definitely up for interface eth0, 1000 Mbps full duplex.
Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
before:
bonding: bond0: link status definitely up for interface eth5
bonding: bond0: link status definitely up for interface eth0
after:
bonding: bond0: link status definitely up for interface eth5, 100 Mbps full duplex.
bonding: bond0: link status definitely up for interface eth0, 100 Mbps full duplex.
Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Client statistics need to be initialized to -1
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does not include any functional changes.
The changes are: empty lines, indentation and comments.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return proper L2 and L5 SPQ (slow path queue) credits. Previously, all
SPQ events were counted as L5 types.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Decide which interrupt mode to use (MSI-X, MSI, INTa) only once in probe() and
initialize appropriate structures.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
