Since the COH 901 327 found in U300 is clocked at 32 kHz we need
to wait for the interrupt clearing flag to propagate through
hardware in order not to accidentally fire off any interrupts
when we enable them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
VLB support has been broken since at least 2004-2005 period as some
changes introduced back then assumed that ->pci_dev is always valid,
lets try to fix it:
- remove duplicated SET_NETDEV_DEV() call
- call SET_NETDEV_DEV() only for PCI devices
- check for ->pci_dev validity in pcnet32_open()
[ Alternatively we may consider removing VLB support but there would not
be much gain in it since an extra driver code needed for VLB support is
minimal and quite simple. ]
This takes care of the following entry from Dan's list:
drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev'
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the debug printk() into the proper place and remove superfluous
NULL pointer check in pcnet32_probe1().
This takes care of the following entry from Dan's list:
drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev'
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a path when an assetion in dev_unicast_sync() appears.
igmp6_group_added -> dev_mc_add -> __dev_set_rx_mode ->
-> vlan_dev_set_rx_mode -> dev_unicast_sync
Therefore we cannot protect this list with rtnl. This patch restores the
original protecting this list with spinlock.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change default dma mask for NX3031 to 39 bit with ability
to update it to 64-bit (if firmware indicates support). Old
code was restricting it under 4GB (32-bit), sometimes causing
failure to allocate descriptor rings on heavily populated
system. NX2031 based NICs will still get 32-bit coherent mask.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether index is within bounds before testing the element.
In the last iteration i is PHY_MAX_ADDR. the condition
`!(p = pd->mii.bus->phy_map[PHY_MAX_ADDR])' is undefined and may
evaluate to false, which leads to a dereference of this invalid
phy_map in the phy_connect() below.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
memcpy() should take into account size of pointers,
not only number of pointers to copy.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure to call unregister_pernet_gen_device() can exhaust memory
if module is loaded/unloaded many times.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the corner cases where the sum of MTU of the free
channels (adjusted for fragmentation overheads) is less than the MTU
of PPP link. There are at least 3 situations where this case might
arise:
- some of the channels are busy
- the multilink session is running in a degraded state (i.e. with less
than its full complement of active channels)
- by design, where multilink protocol is being used to artificially
increase the effective link MTU of a single link.
Without this patch, at most 1 fragment is ever sent per free channel
for a given PPP frame and any remaining part of the PPP frame that
does not fit into those fragments is silently discarded.
This patch restores the original behaviour which was broken by commit
9c705260fe 'ppp:ppp_mp_explode()
redesign'. Once all 'free' channels have been given a fragment, an
additional fragment is queued to each available channel in turn, as many
times as necessary, until the entire PPP frame has been consumed.
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
OOPS on resume when the wireless adaptor is disabled during suspend was
introduced by "eeepc-laptop: read rfkill soft-blocked state on resume".
Unable to handle kernel NULL pointer dereference
Process s2disk
Tainted: G W
IP: klist_put
Call trace:
? klist_del
? device_del
? device_unregister
? pci_stop_dev
? pci_stop_bus
? pci_remove_device
? eeepc_rfkill_hotplug [eeepc_laptop]
? eeepc_hotk_resume [eeepc_laptop]
? acpi_device_resume
? device_resume
? hibernation_snapshot
It appears the PCI device is removed twice. The eeepc_rfkill_hotplug()
call from the resume handler is racing against the call from the ACPI
notifier callback. The ACPI notification is triggered by the resume
handler when it refreshes the value of CM_ASL_WLAN.
The fix is to serialize hotplug calls using a workqueue.
http://bugzilla.kernel.org/show_bug.cgi?id=13825
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If the memory block size is zero, ignore it and don't do the memory hotplug
flowchart. Otherwise it will complain the following warning message:
>System RAM resource 0 - ffffffffffffffff cannot be added
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Don't treat the generic error as ACPI error code. Otherwise when the generic
code is returned, it will complain the following warning messag:
>ACPI Exception (acpi_memhotplug-0171): UNKNOWN_STATUS_CODE,
Cannot get acpi bus device [20080609]
>ACPI: Cannot find driver data
> ACPI Error (utglobal-0127): Unknown exception code: 0xFFFFFFED [20080609]
> Pid: 85, comm: kacpi_notify Not tainted 2.6.27.19-5-default #1
Call Trace:
[<ffffffff8020da29>] show_trace_log_lvl+0x41/0x58
[<ffffffff8049a3da>] dump_stack+0x69/0x6f
.....
At the same time when the generic error code is returned, the ACPI_EXCEPTION
is replaced by the printk.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On some machines, a software-initiated SMI causes corruption unless the
SMI runs on CPU 0. An SMI can be initiated by any AML, but typically it's
done in GPE-related methods that are run via workqueues, so we can avoid
the known corruption cases by binding the workqueues to CPU 0.
References:
http://bugzilla.kernel.org/show_bug.cgi?id=13751https://bugs.launchpad.net/bugs/157171https://bugs.launchpad.net/bugs/157691
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix those warnings:
drivers/parisc/hppb.c: In function 'hppb_probe':
drivers/parisc/hppb.c:65: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
drivers/parisc/hppb.c:77: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/parisc/hppb.c:77: warning: format '%08x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Helge Deller <deller@gmx.de>
Fix those compiler warnings, which indeed point to a bug:
drivers/char/agp/parisc-agp.c:228: warning: initialization from incompatible pointer type
drivers/char/agp/parisc-agp.c:201: warning: 'parisc_agp_page_mask_memory' defined but not used
Signed-off-by: Helge Deller <deller@gmx.de>
This adds a missing unlock of nilfs->ns_writer_mutex in
nilfs_mdt_write_page() function.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Background:
Several race conditions in the scheduler have cropped up
recently, which Steven and I have tracked down using ftrace.
The most recent one turns out to be a race in how the scheduler
determines a suitable migration target for RT tasks, introduced
recently with commit:
commit 68e74568fb
Date: Tue Nov 25 02:35:13 2008 +1030
sched: convert struct cpupri_vec cpumask_var_t.
The original design of cpupri allowed lockless readers to
quickly determine a best-estimate target. Races between the
pri_active bitmap and the vec->mask were handled in the
original code because we would detect and return "0" when this
occured. The design was predicated on the *effective*
atomicity (*) of caching the result of cpus_and() between the
cpus_allowed and the vec->mask.
Commit 68e74568 changed the behavior such that vec->mask is
accessed multiple times. This introduces a subtle race, the
result of which means we can have a result that returns "1",
but with an empty bitmap.
*) yes, we know cpus_and() is not a locked operator across the
entire composite array, but it is implicitly atomic on a
per-word basis which is all the design required to work.
Implementation:
Rather than forgoing the lockless design, or reverting to a
stack-based cpumask_t, we simply check for when the race has
been encountered and continue processing in the event that the
race is hit. This renders the removal race as if the priority
bit had been atomically cleared as well, and allows the
algorithm to execute correctly.
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090730145728.25226.92769.stgit@dev.haskins.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The latencytop and sleep accounting code assumes that any
scheduler entity represents a task, this is not so.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We skip the display of idle routine related symbols because
they are typically rather erratic and confusing: they depend
on the IRQ rate or sometimes they dominate the profile if
they are polling based.
Add mwait_idle_with_hints too, this is one of the idle
routines on x86.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes a spelling error that has resulted from copy
and pasting. The location of the error was found using a
semantic patch but the semantic patch was not trying to find
these errors. After looking things over it seemed logical that
this change was needed. Please review it and then include the
patch if it is in fact the correct change.
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1248949529-20891-1-git-send-email-sgayda2@uiuc.edu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since FORK is now also issued for threads, detect those by
comparing the parent and child PID.
Teach it about EXIT events and ignore them.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In order to be able to distinguish between no samples due to
inactivity and no samples due to task ended, Arjan asked for
PERF_EVENT_EXIT events. This is useful to the boot delay
instrumentation (bootchart) app.
This patch changes the PERF_EVENT_FORK to be emitted on every
clone, and adds PERF_EVENT_EXIT to be emitted on task exit,
after the task's counters have been closed.
This task tracing is controlled through: attr.comm || attr.mmap
and through the new attr.task field.
Suggested-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
[ cleaned up perf_counter.h a bit ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the counter value returned by read() is the value of
the parent counter, to which child counters are only fed back
on child exit.
Thus read() can return rather erratic (and meaningless) numbers
depending on the state of the child processes.
Change this by always iterating the full child hierarchy on
read() and sum all counters.
Suggested-by: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix the following 'make includecheck' warning:
drivers/parisc/ccio-dma.c: linux/proc_fs.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
loff_t is a signed type. If userspace passes a negative ppos, the "count"
range check is weakened. "count"s bigger than HPEE_MAX_LENGTH will pass the check.
Also, if ppos is negative, the readb(eisa_eeprom_addr + *ppos) will poke in random
memory.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable@kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
This patche fixes a spelling error that has resulted from copy and pasting.
The location of the error was found using a semantic patch but the semantic
patch was not trying to find these errors. After looking things over it
seemed logical that this change was needed.
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Helge Deller <deller@gmx.de>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
HBRV-based default selection of backlight control strategy didn't work
well, at least the X41 defines it but doesn't use it and I don't think
it will stop there.
Switch to a white/blacklist. All models that have HBRV defined have
been included in the list, and initially all ATI GPUs will get
ECNVRAM, and the Intel GPUs will get UCMS_STEP.
Symptoms of incorrect backlight mode selection are:
1. Non-working backlight control through sysfs;
2. Backlight gets reset to the lowest level at every shutdown, reboot
and when thinkpad-acpi gets unloaded;
This fixes a regression in 2.6.30, bugzilla #13826
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes the regression reported here:
http://bugzilla.kernel.org/show_bug.cgi?id=13861
commit 4ae1507f6d changed the default
behavior when the uid= or gid= option was specified for a mount. The
existing behavior was to always clobber the ownership information
provided by the server when these options were specified. The above
commit changed this behavior so that these options simply provided
defaults when the server did not provide this information (unless
"forceuid" or "forcegid" were specified)
This patch reverts this change so that the default behavior is restored.
It also adds "noforceuid" and "noforcegid" options to make it so that
ownership information from the server is preserved, even when the mount
has uid= or gid= options specified.
It also adds a couple of printk notices that pop up when forceuid or
forcegid options are specified without a uid= or gid= option.
Reported-by: Tom Chiverton <bugzilla.kernel.org@falkensweb.com>
Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The standard ACPI dock driver can handle the hotplug bays and docks of
the ThinkPads just fine (including batteries) as of 2.6.27, and the
code in thinkpad-acpi for the dock and bay subdrivers is currently
broken anyway...
Userspace needs some love to support the two-stage ejection nicely,
but it is simple enough to do through udev rules (you don't even need
HAL) so this wouldn't justify fixing the dock and bay subdrivers,
either.
That leaves warm-swap bays (_EJ3) support for thinkpad-acpi, as well
as support for the weird dock of the model 570, but since such support
has never left the "experimental" stage, it is also not a strong
enough reason to find a way to fix this code.
Users of ThinkPads with warm-swap bays are urged to request that _EJ3
support be added to the regular ACPI dock driver, if such feature is
indeed useful for them.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently, the ThinkPad-ACPI bay and dock drivers are completely
broken, and cause a NULL pointer derreference in kernel mode (and,
therefore, an OOPS) when they try to issue events (i.e. on dock,
undock, bay ejection, etc).
OTOH, the standard ACPI dock driver can handle the hotplug bays and
docks of the ThinkPads just fine (including batteries) as of 2.6.27.
In fact, it does a much better job of it than thinkpad-acpi ever did.
It is just not worth the hassle to find a way to fix this crap without
breaking the (deprecated) thinkpad-acpi dock/bay ABI. This is old,
deprecated code that sees little testing or use.
As a quick fix suitable for -stable backports, mark the thinkpad-acpi
bay and dock subdrivers as BROKEN in Kconfig. The dead code will be
removed by a later patch.
This fixes bugzilla #13669, and should be applied to 2.6.27 and later.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Joerg Platte <jplatte@naasa.net>
Cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
The previous commit ("do_sigaltstack: avoid copying 'stack_t' as a
structure to user space") fixed a real bug. This one just cleans up the
copy from user space to that gcc can generate better code for it (and so
that it looks the same as the later copy back to user space).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ulrich Drepper correctly points out that there is generally padding in
the structure on 64-bit hosts, and that copying the structure from
kernel to user space can leak information from the kernel stack in those
padding bytes.
Avoid the whole issue by just copying the three members one by one
instead, which also means that the function also can avoid the need for
a stack frame. This also happens to match how we copy the new structure
from user space, so it all even makes sense.
[ The obvious solution of adding a memset() generates horrid code, gcc
does really stupid things. ]
Reported-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
