This driver is a Full / Low speed only USB host for the i.MX21.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This centralize some spread-out initialization of descriptors into
one function and cleans up the error paths.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (214 commits)
omap2: Initialize Menelaus and MMC for N8X0
AM3517 EVM: correct typo - tca6416 mispelt as tca6516
AM3517 EVM: Enable I2C support
AM35x: Enable OMAP_MUX in defconfig
AM35x: Add missing GPIO mux config for EHCI port
Zoom3: Defconfig update
omap: i2c: Fix muxing for command line enabled bus
OMAP4: clock: Remove clock hacks from timer-gp.c
OMAP4: clock: Add dummy clock nodes for interface clocks
OMAP4: clock: Rename leaf clock nodes to end with a _ick or _fck
OMAP2+ clock: revise omap2_clk_{disable,enable}()
OMAP2/3 clock: combine OMAP2 & 3 boot-time MPU rate change code
OMAP clockdomain: if no autodeps exist, don't try to add or remove them
OMAP hwmod: add hwmod class support
OMAP hwmod: convert header files with static allocations into C files
OMAP hwmod: convert hwmod to use hardware clock names rather than clkdev dev+con
OMAP clock: add omap_clk_get_by_name() for use by OMAP hwmod core code
OMAP3: clock: add capability to change rate of dpll4_m5_ck_3630
OMAP4 clock: drop the ALWAYS_ENABLED clock flag
OMAP clock: drop RATE_FIXED clock flag
...
Set GPIO bits to pull the pins connected to LEDs for lower power mode.
We want all LEDs off when devices are in suspend.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Amit Walambe <amit.walambe@eurotech.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Amit Walambe <amit.walambe@eurotech.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Zeus console port is wired to a 8250-compatible device (pxa UARTs are
reserved to other uses). This patch allows such a configuration in the
uncompress sequence.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The original patch came from Marc Zyngier where support of 8250-compatible
UART is required to show the uncompress information. Modified a little bit
here, including changes below:
1. #include <mach/regs-uart.h> is actually not necessary
2. introduced uart_{read,write}() for different base and shift
3. introduced uart_is_enabled() and assumed enabled always for
non-PXA uarts
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
The irq_chip is not yet registered, so no default irq_chip.mask_ack(),
which we have to handle it correctly manually here.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since PMIC INT pin is a special pin of CPU, the status of PMIC INT pin needs
to be cleared after PMIC IRQ occured. Now append the clear operation in
irq chip handler.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Marvell MMP2 (aka ARMADA610) is a SoC based on PJ4 core. It's
ARMv6 compatible. Support basic interrupt handler and timer,
and basic support for MMP2 based FLINT platform.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Also remove a trailing whitespace while being there.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add some safety check for CONFIG_PM around zeus_power_off(). Without
it linking can fail like this:
arch/arm/mach-pxa/built-in.o: In function `zeus_power_off':
e800.c:(.text+0x2bc8): undefined reference to `pxa27x_cpu_suspend'
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This function gets only called from scoop_suspend() and scoop_resume() which are
only built in if we have CONFIG_PM set. Make it the same for check_scoop_reg().
This fixes the following warning:
arch/arm/common/scoop.c:143: warning: ‘check_scoop_reg’ defined but not used
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
IRQ_LOCOMO_* are never used elsewhere, remove these definitions. As well
as the cascade of these IRQs. IRQ_LOCOMO_*_BASE changed to IRQ_LOCOMO_*.
IRQ_LOCOMO_LT and IRQ_LOCOMO_SPI are likely to be used in a same way as
IRQ_LOCOMO_KEY.
IRQ_LOCOMO_GPIO and the demultiplex handler should really be living
somewhere else.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to
be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced
locomokbd_{open,close} for masking/unmasking of the keyboard IRQ.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Missing AC97 pin configurations are added where pxa_set_ac97_info() are
called for all pxa25x/pxa27x platforms. Where no exact configuration is
provided, use the default as in sound/arm/pxa2xx-ac97-lib.c
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is really pxa27x specific and should be kept in pxa27x.c. With this
newly introduced function, the original set_resetgpio_mode() is deprecated.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (40 commits)
DaVinci DM365: Adding support for SPI EEPROM
DaVinci DM365: Adding DM365 SPI support
DaVinci DM355: Modifications to DM355 SPI support
DaVinci: SPI: Adding header file for SPI support.
davinci: dm646x: CDCE clocks: davinci_clk converted to clk_lookup
davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table()
DaVinci: DM365: Voice codec support for the DM365 SoC
davinci: clock: let clk->set_rate function sleep
Add SDA and SCL pin numbers to i2c platform data
davinci: da8xx/omap-l1xx: Add EDMA platform data for da850/omap-l138
davinci: build list of unused EDMA events dynamically
davinci: Fix edma_alloc_channel api for EDMA_CHANNEL_ANY case
davinci: Keep count of channel controllers on a platform
davinci: Correct return value of edma_alloc_channel api
davinci: add CDCE949 support on DM6467 EVM
davinci: add support for CDCE949 clock synthesizer
davinci: da850/omap-l138 EVM: register for suspend support
davinci: da850/omap-l138: add support for SoC suspend
davinci: add power management support
DaVinci: DM365: Changing default queue for DM365.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (62 commits)
Input: atkbd - release previously reserved keycodes 248 - 254
Input: add KEY_WPS_BUTTON definition
Input: ads7846 - add regulator support
Input: winbond-cir - fix suspend/resume
Input: gamecon - use pr_err() and friends
Input: gamecon - constify some of the setup structures
Input: gamecon - simplify pad type handling
Input: gamecon - simplify coordinate calculation for PSX
Input: gamecon - fix some formatting issues
Input: gamecon - add rumble support for N64 pads
Input: wacom - add device type to device name string
Input: s3c24xx_ts - report touch only when stylus is down
Input: s3c24xx_ts - re-enable IRQ on resume
Input: wacom - constify product features data
Input: wacom - use per-device instance of wacom_features
Input: sh_keysc - enable building on SH-Mobile ARM
Input: wacom - get features from driver info
Input: rotary-encoder - set gpio direction for each requested gpio
Input: sh_keysc - update the driver with mode 6
Input: sh_keysc - switch to using bitmaps
...
The DM365 Spectrum Digital EVM comes with an EEPROM
connected to SPI0.
This patch adds support for the SPI EEPROM.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>