Rather than always releasing the prisoners in a cell, the client may
want to promote one of them to be the new holder. There is a race here
though between releasing an empty cell, and other threads adding new
inmates. So this function makes the decision with its lock held.
This function can have two outcomes:
i) An inmate is promoted to be the holder of the cell (return value of 0).
ii) The cell has no inmate for promotion and is released (return value of 1).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
We only allow non critical writeback if the origin is idle. It is up
to the policy to decide what writeback work is critical.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A little class that keeps track of the volume of io that is in flight,
and the length of time that a device has been idle for.
FIXME: rather than jiffes, may be best to use ktime_t (to support faster
devices).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There is a race between a policy deciding to replace a cache entry,
the core target writing back any dirty data from this block, and other
IO threads doing IO to the same block.
This sort of problem is avoided most of the time by the core target
grabbing a bio prison cell before making the request to the policy.
But for a demotion the core target doesn't know which block will be
demoted, so can't do this in advance.
Fix this demotion race by introducing a callback to the policy interface
that allows the policy to grab the cell on behalf of the core target.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
A crypto driver can process requests synchronously or asynchronously
and can use an internal driver queue to backlog requests.
Add some comments to clarify internal logic and completion return codes.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Currently if there is a leg failure, the bio will be put into the hold
list until userspace does a remove/replace on the leg. Doing so in a
cluster config (clvmd) is problematic because there may be a temporary
path failure that results in cluster raid1 remove/replace. Such
recovery takes a long time due to a full resync.
Update dm-raid1 to optionally ignore these failures so bios continue
being issued without interrupton. To enable this feature userspace
must pass "keep_log" when creating the dm-raid1 device.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Tested-by: Liuhua Wang <lwang@suse.com>
Acked-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
On 32-bit:
drivers/md/dm-log-writes.c: In function ‘log_super’:
drivers/md/dm-log-writes.c:323: warning: integer constant is too large for ‘long’ type
Add a ULL suffix to WRITE_LOG_MAGIC to fix this.
Also add a ULL suffix to WRITE_LOG_VERSION as it's stored in a __le64
field.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add dm-raid access to the MD RAID0 personality to enable single zone
striping.
The following changes enable that access:
- add type definition to raid_types array
- make bitmap creation conditonal in super_validate(), because
bitmaps are not allowed in raid0
- set rdev->sectors to the data image size in super_validate()
to allow the raid0 personality to calculate the MD array
size properly
- use mdddev(un)lock() functions instead of direct mutex_(un)lock()
(wrapped in here because it's a trivial change)
- enhance raid_status() to always report full sync for raid0
so that userspace checks for 100% sync will succeed and allow
for resize (and takeover/reshape once added in future paches)
- enhance raid_resume() to not load bitmap in case of raid0
- add merge function to avoid data corruption (seen with readahead)
that resulted from bio payloads that grew too large. This problem
did not occur with the other raid levels because it either did not
apply without striping (raid1) or was avoided via stripe caching.
- raise version to 1.7.0 because of the raid0 API change
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- ensure maximum device limit in superblock
- rename DMPF_* (print flags) to CTR_FLAG_* (constructor flags)
and their respective struct raid_set member
- use strcasecmp() in raid10_format_to_md_layout() as in the constructor
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Remove comment above parse_raid_params() that claims
"devices_handle_discard_safely" is a table line argument when it is
actually is a module parameter.
Also, backfill dm-raid target version 1.6.0 documentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Leverage the block manager's read_only flag instead of duplicating it;
access with new dm_bm_is_read_only() method.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The overwrite has only ever about optimizing away the need to zero a
block if the entire block was being overwritten. As such it is only
relevant when zeroing is enabled.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Introduce a single common method for cleaning up a DM device's
mapped_device. No functional change, just eliminates duplication of
delicate mapped_device cleanup code.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
More often than not a request that is requeued _is_ mapped (meaning the
clone request is allocated and clone->q is initialized). Rename
dm_requeue_unmapped_original_request() to avoid potential confusion due
to function name containing "unmapped".
Also, remove dm_requeue_unmapped_request() since callers can easily call
the dm_requeue_original_request() directly.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Do not allocate the io_pool mempool for blk-mq request-based DM
(DM_TYPE_MQ_REQUEST_BASED) in dm_alloc_rq_mempools().
Also refine __bind_mempools() to have more precise awareness of which
mempools each type of DM device uses -- avoids mempool churn when
reloading DM tables (particularly for DM_TYPE_REQUEST_BASED).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm_merge_bvec() was originally added in f6fccb ("dm: introduce
merge_bvec_fn"). In that commit a value in sectors is converted to
bytes using << 9, and then assigned to an int. This code made
assumptions about the value of BIO_MAX_SECTORS.
A later commit 148e51 ("dm: improve documentation and code clarity in
dm_merge_bvec") was meant to have no functional change but it removed
the use of BIO_MAX_SECTORS in favor of using queue_max_sectors(). At
this point the cast from sector_t to int resulted in a zero value. The
fallout being dm_merge_bvec() would only allow a single page to be added
to a bio.
This interim fix is minimal for the benefit of stable@ because the more
comprehensive cleanup of passing a sector_t to all DM targets' merge
function will impact quite a few DM targets.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.19+
dm-multipath accepts 0 path mapping.
# echo '0 2097152 multipath 0 0 0 0' | dmsetup create newdev
Such a mapping can be used to release underlying devices while still
holding requests in its queue until working paths come back.
However, once the multipath device is created over blk-mq devices,
it rejects reloading of 0 path mapping:
# echo '0 2097152 multipath 0 0 1 1 queue-length 0 1 1 /dev/sda 1' \
| dmsetup create mpath1
# echo '0 2097152 multipath 0 0 0 0' | dmsetup load mpath1
device-mapper: reload ioctl on mpath1 failed: Invalid argument
Command failed
With following kernel message:
device-mapper: ioctl: can't change device type after initial table load.
DM tries to inherit the current table type using dm_table_set_type()
but it doesn't work as expected because of unnecessary check about
whether the target type is hybrid or not.
Hybrid type is for targets that work as either request-based or bio-based
and not required for blk-mq or non blk-mq checking.
Fixes: 65803c205983 ("dm table: train hybrid target type detection to select blk-mq if appropriate")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Unfortunately this functionality was merged a little prematurely.
The necessary testing and code review is now complete (or as
complete as it can be) and to code passes a variety of tests
and looks quite sensible.
Also a fix for some recent locking changes - a race was introduced
which causes a reshape request to sometimes fail. No data safety issues.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Y0Vm
-----END PGP SIGNATURE-----
Merge tag 'md/4.1-rc5-fixes' of git://neil.brown.name/md
Pull m,ore md bugfixes gfrom Neil Brown:
"Assorted fixes for new RAID5 stripe-batching functionality.
Unfortunately this functionality was merged a little prematurely. The
necessary testing and code review is now complete (or as complete as
it can be) and to code passes a variety of tests and looks quite
sensible.
Also a fix for some recent locking changes - a race was introduced
which causes a reshape request to sometimes fail. No data safety
issues"
* tag 'md/4.1-rc5-fixes' of git://neil.brown.name/md:
md: fix race when unfreezing sync_action
md/raid5: break stripe-batches when the array has failed.
md/raid5: call break_stripe_batch_list from handle_stripe_clean_event
md/raid5: be more selective about distributing flags across batch.
md/raid5: add handle_flags arg to break_stripe_batch_list.
md/raid5: duplicate some more handle_stripe_clean_event code in break_stripe_batch_list
md/raid5: remove condition test from check_break_stripe_batch_list.
md/raid5: Ensure a batch member is not handled prematurely.
md/raid5: close race between STRIPE_BIT_DELAY and batching.
md/raid5: ensure whole batch is delayed for all required bitmap updates.
When stacking request-based dm device on non blk-mq device and
device-mapper target could not map the request (error target is used,
multipath target with all paths down, etc), the WARN_ON_ONCE() in
free_rq_clone() will trigger when it shouldn't.
The warning was added by commit aa6df8d ("dm: fix free_rq_clone() NULL
pointer when requeueing unmapped request"). But free_rq_clone() with
clone->q == NULL is valid usage for the case where
dm_kill_unmapped_request() initiates request cleanup.
Fix this false warning by just removing the WARN_ON -- it only generated
false positives and was never useful in catching the intended case
(completing clone request not being mapped e.g. clone->q being NULL).
Fixes: aa6df8d ("dm: fix free_rq_clone() NULL pointer when requeueing unmapped request")
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A recent change removed the need for locking around writing
to "sync_action" (and various other places), but introduced a
subtle race.
When e.g. setting 'reshape' on a 'frozen' array, the 'frozen'
flag is cleared before 'reshape' is set, so the md thread can
get in and start trying recovery - which isn't wanted.
So instead of clearing MD_RECOVERY_FROZEN for any command
except 'frozen', only clear it when each specific command
is parsed. This allows the handling of 'reshape' to clear
the bit while a lock is held.
Also remove some places where we set MD_RECOVERY_NEEDED,
as it is always set on non-error exit of the function.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 6791875e2e53 ("md: make reconfig_mutex optional for writes to md sysfs files.")
Now that the code in break_stripe_batch_list() is nearly identical
to the end of handle_stripe_clean_event, replace the later
with a function call.
The only remaining difference of any interest is the masking that is
applieds to dev[i].flags copied from head_sh.
R5_WriteError certainly isn't wanted as it is set per-stripe, not
per-patch. R5_Overlap isn't wanted as it is explicitly handled.
Signed-off-by: NeilBrown <neilb@suse.de>
When a batch of stripes is broken up, we keep some of the flags
that were per-stripe, and copy other flags from the head to all
others.
This only happens while a stripe is being handled, so many of the
flags are irrelevant.
The "SYNC_FLAGS" (which I've renamed to make it clear there are
several) and STRIPE_DEGRADED are set per-stripe and so need to be
preserved. STRIPE_INSYNC is the only flag that is set on the head
that needs to be propagated to all others.
For safety, add a WARN_ON if others are set, except:
STRIPE_HANDLE - this is safe and per-stripe and we are going to set
in several cases anyway
STRIPE_INSYNC
STRIPE_IO_STARTED - this is just a hint and doesn't hurt.
STRIPE_ON_PLUG_LIST
STRIPE_ON_RELEASE_LIST - It is a point pointless for a batched
stripe to be on one of these lists, but it can happen
as can be safely ignored.
Signed-off-by: NeilBrown <neilb@suse.de>
When we break a stripe_batch_list we sometimes want to set
STRIPE_HANDLE on the individual stripes, and sometimes not.
So pass a 'handle_flags' arg. If it is zero, always set STRIPE_HANDLE
(on non-head stripes). If not zero, only set it if any of the given
flags are present.
Signed-off-by: NeilBrown <neilb@suse.de>
break_stripe_batch list didn't clear head_sh->batch_head.
This was probably a bug.
Also clear all R5_Overlap flags and if any were cleared, wake up
'wait_for_overlap'.
This isn't always necessary but the worst effect is a little
extra checking for code that is waiting on wait_for_overlap.
Also, don't use wake_up_nr() because that does the wrong thing
if 'nr' is zero, and it number of flags cleared doesn't
strongly correlate with the number of threads to wake.
Signed-off-by: NeilBrown <neilb@suse.de>
handle_stripe_clean_event() contains a chunk of code very
similar to check_break_stripe_batch_list().
If we make the latter more like the former, we can end up
with just one copy of this code.
This first step removed the condition (and the 'check_') part
of the name. This has the added advantage of making it clear
what check is being performed at the point where the function is
called.
Signed-off-by: NeilBrown <neilb@suse.de>
If a stripe is a member of a batch, but not the head, it must
not be handled separately from the rest of the batch.
'clear_batch_ready()' handles this requirement to some
extent but not completely. If a member is passed to handle_stripe()
a second time it returns '0' indicating the stripe can be handled,
which is wrong.
So add an extra test.
Signed-off-by: NeilBrown <neilb@suse.de>
When we add a write to a stripe we need to make sure the bitmap
bit is set. While doing that the stripe is not locked so it could
be added to a batch after which further changes to STRIPE_BIT_DELAY
and ->bm_seq are ineffective.
So we need to hold off adding to a stripe until bitmap_startwrite has
completed at least once, and we need to avoid further changes to
STRIPE_BIT_DELAY once the stripe has been added to a batch.
If a bitmap_startwrite() completes after the stripe was added to a
batch, it will not have set the bit, only incremented a counter, so no
extra delay of the stripe is needed.
Reported-by: Shaohua Li <shli@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>
When we add a stripe to a batch, we need to be sure that
head stripe will wait for the bitmap update required for the new
stripe.
Signed-off-by: NeilBrown <neilb@suse.de>
Use BLK_MQ_RQ_QUEUE_BUSY to requeue a blk-mq request directly from the
DM blk-mq device's .queue_rq. This cleans up the previous convoluted
handling of request requeueing that would return BLK_MQ_RQ_QUEUE_OK
(even though it wasn't) and then run blk_mq_requeue_request() followed
by blk_mq_kick_requeue_list().
Also, document that DM blk-mq ontop of old request_fn devices cannot
fail in clone_rq() since the clone request is preallocated as part of
the pdu.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When stacking request-based DM on blk_mq device, request cloning and
remapping are done in a single call to target's clone_and_map_rq().
The clone is allocated and valid only if clone_and_map_rq() returns
DM_MAPIO_REMAPPED.
The "IS_ERR(clone)" check in map_request() does not cover all the
!DM_MAPIO_REMAPPED cases that are possible (E.g. if underlying devices
are not ready or unavailable, clone_and_map_rq() may return
DM_MAPIO_REQUEUE without ever having established an ERR_PTR). Fix this
by explicitly checking for a return that is not DM_MAPIO_REMAPPED in
map_request().
Without this fix, DM core may call setup_clone() for a NULL clone
and oops like this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000068
IP: [<ffffffff81227525>] blk_rq_prep_clone+0x7d/0x137
...
CPU: 2 PID: 5793 Comm: kdmwork-253:3 Not tainted 4.0.0-nm #1
...
Call Trace:
[<ffffffffa01d1c09>] map_tio_request+0xa9/0x258 [dm_mod]
[<ffffffff81071de9>] kthread_worker_fn+0xfd/0x150
[<ffffffff81071cec>] ? kthread_parkme+0x24/0x24
[<ffffffff81071cec>] ? kthread_parkme+0x24/0x24
[<ffffffff81071fdd>] kthread+0xe6/0xee
[<ffffffff81093a59>] ? put_lock_stats+0xe/0x20
[<ffffffff81071ef7>] ? __init_kthread_worker+0x5b/0x5b
[<ffffffff814c2d98>] ret_from_fork+0x58/0x90
[<ffffffff81071ef7>] ? __init_kthread_worker+0x5b/0x5b
Fixes: e5863d9ad ("dm: allocate requests in target when stacking on blk-mq devices")
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.0+
Without kicking queue, requeued request may stay forever in
the queue if there are no other I/O activities to the device.
The original error had been in v2.6.39 with commit 7eaceaccab5f
("block: remove per-queue plugging"), which replaced conditional
plugging by periodic runqueue.
Commit 9d1deb83d489 in v4.1-rc1 removed the periodic runqueue
and the problem started to manifest.
Fixes: 9d1deb83d489 ("dm: don't schedule delayed run of the queue if nothing to do")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- one serious RAID0 data corruption - caused by recent bugfix that wasn't
reviewed properly.
- one raid5 fix in new code (a couple more of those to come).
- one little fix to stop static analysis complaining about silly rcu
annotation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jXKM
-----END PGP SIGNATURE-----
Merge tag 'md/4.1-rc4-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"I have a few more raid5 bugfixes pending, but I want them to get a bit
more review first. In the meantime:
- one serious RAID0 data corruption - caused by recent bugfix that
wasn't reviewed properly.
- one raid5 fix in new code (a couple more of those to come).
- one little fix to stop static analysis complaining about silly rcu
annotation"
* tag 'md/4.1-rc4-fixes' of git://neil.brown.name/md:
md/bitmap: remove rcu annotation from pointer arithmetic.
md/raid0: fix restore to sector variable in raid0_make_request
raid5: fix broken async operation chain
Currently dm-multipath has to clone the bios for every request sent
to the lower devices, which wastes cpu cycles and ties down memory.
This patch instead adds a new REQ_CLONE flag that instructs req_bio_endio
to not complete bios attached to a request, which we set on clone
requests similar to bios in a flush sequence. With this change I/O
errors on a path failure only get propagated to dm-multipath, which
can then either resubmit the I/O or complete the bios on the original
request.
I've done some basic testing of this on a Linux target with ALUA support,
and it survives path failures during I/O nicely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit c4cf5261 ("bio: skip atomic inc/dec of ->bi_remaining for
non-chains") regressed all existing callers that followed this pattern:
1) saving a bio's original bi_end_io
2) wiring up an intermediate bi_end_io
3) restoring the original bi_end_io from intermediate bi_end_io
4) calling bio_endio() to execute the restored original bi_end_io
The regression was due to BIO_CHAIN only ever getting set if
bio_inc_remaining() is called. For the above pattern it isn't set until
step 3 above (step 2 would've needed to establish BIO_CHAIN). As such
the first bio_endio(), in step 2 above, never decremented __bi_remaining
before calling the intermediate bi_end_io -- leaving __bi_remaining with
the value 1 instead of 0. When bio_inc_remaining() occurred during step
3 it brought it to a value of 2. When the second bio_endio() was
called, in step 4 above, it should've called the original bi_end_io but
it didn't because there was an extra reference that wasn't dropped (due
to atomic operations being optimized away since BIO_CHAIN wasn't set
upfront).
Fix this issue by removing the __bi_remaining management complexity for
all callers that use the above pattern -- bio_chain() is the only
interface that _needs_ to be concerned with __bi_remaining. For the
above pattern callers just expect the bi_end_io they set to get called!
Remove bio_endio_nodec() and also remove all bio_inc_remaining() calls
that aren't associated with the bio_chain() interface.
Also, the bio_inc_remaining() interface has been moved local to bio.c.
Fixes: c4cf5261 ("bio: skip atomic inc/dec of ->bi_remaining for non-chains")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Evaluating "&mddev->disks" is simple pointer arithmetic, so
it does not need 'rcu' annotations - no dereferencing is happening.
Also enhance the comment to explain that 'rdev' in that case
is not actually a pointer to an rdev.
Reported-by: Patrick Marlier <patrick.marlier@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The variable "sector" in "raid0_make_request()" was improperly updated
by a call to "sector_div()" which modifies its first argument in place.
Commit 47d68979cc968535cb87f3e5f2e6a3533ea48fbd restored this variable
after the call for later re-use. Unfortunetly the restore was done after
the referenced variable "bio" was advanced. This lead to the original
value and the restored value being different. Here we move this line to
the proper place.
One observed side effect of this bug was discarding a file though
unlinking would cause an unrelated file's contents to be discarded.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 47d68979cc96 ("md/raid0: fix bug with chunksize not a power of 2.")
Cc: stable@vger.kernel.org (any that received above backport)
URL: https://bugzilla.kernel.org/show_bug.cgi?id=98501
ops_run_reconstruct6() doesn't correctly chain asyn operations. The tx returned
by async_gen_syndrome should be added as the dependent tx of next stripe.
The issue is introduced by commit 59fc630b8b5f9f21c8ce3ba153341c107dce1b0c
RAID5: batch adjacent full stripe write
Reported-and-tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Most of these are related to the new "batched stripe writeout",
but there are a few others.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=tapF
-----END PGP SIGNATURE-----
Merge tag 'md/4.1-rc3-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"A few fixes for md.
Most of these are related to the new "batched stripe writeout", but
there are a few others"
* tag 'md/4.1-rc3-fixes' of git://neil.brown.name/md:
md/raid5: fix handling of degraded stripes in batches.
md/raid5: fix allocation of 'scribble' array.
md/raid5: don't record new size if resize_stripes fails.
md/raid5: avoid reading parity blocks for full-stripe write to degraded array
md/raid5: more incorrect BUG_ON in handle_stripe_fill.
md/raid5: new alloc_stripe() to allocate an initialize a stripe.
md-raid0: conditional mddev->queue access to suit dm-raid
window: The first reverts a dm-crypt change that wasn't correct. The
second fixes a device format regression that impacted userspace.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVTRZOAAoJEMUj8QotnQNaW7EIAJlHn+S8czm1Cb4gWBn7kg+X
vzH5NIzr/SpDX8o3R8NBdrB8rgqTm4jQZrptbmgLG+j9XoaQupuFyNCiaAw47v2G
P/WYlodNwTkb3I48XjwCRo00MtR3cEJ8ywNzvEJUvgPkgMMIzhieHsVT9L8bZv3n
XDs8JzZyF966U0BeCjF4oDAazUrpEvWf0h4C5L47g8C0UQI7aGwYKoSvZm3DAImP
awbJbnqtQuoRcI0HISHrjYi1vghgnmJY6aSx3tYSJPTNRkFNqgap7eZrUacicnOH
bUVL3snBVebK3JMJhJXgfGW/FeeP9juhEY08JNTOZ5wa6BNuru0GHeqKuI3arHY=
=jlAN
-----END PGP SIGNATURE-----
Merge tag 'dm-4.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two additional fixes for changes introduced via DM during the 4.1
merge window.
The first reverts a dm-crypt change that wasn't correct. The second
fixes a device format regression that impacted userspace"
* tag 'dm-4.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
init: fix regression by supporting devices with major:minor:offset format
Revert "dm crypt: fix deadlock when async crypto algorithm returns -EBUSY"
Pull block fixes from Jens Axboe:
"A collection of fixes since the merge window;
- fix for a double elevator module release, from Chao Yu. Ancient bug.
- the splice() MORE flag fix from Christophe Leroy.
- a fix for NVMe, fixing a patch that went in in the merge window.
From Keith.
- two fixes for blk-mq CPU hotplug handling, from Ming Lei.
- bdi vs blockdev lifetime fix from Neil Brown, fixing and oops in md.
- two blk-mq fixes from Shaohua, fixing a race on queue stop and a
bad merge issue with FUA writes.
- division-by-zero fix for writeback from Tejun.
- a block bounce page accounting fix, making sure we inc/dec after
bouncing so that pre/post IO pages match up. From Wang YanQing"
* 'for-linus' of git://git.kernel.dk/linux-block:
splice: sendfile() at once fails for big files
blk-mq: don't lose requests if a stopped queue restarts
blk-mq: fix FUA request hang
block: destroy bdi before blockdev is unregistered.
block:bounce: fix call inc_|dec_zone_page_state on different pages confuse value of NR_BOUNCE
elevator: fix double release of elevator module
writeback: use |1 instead of +1 to protect against div by zero
blk-mq: fix CPU hotplug handling
blk-mq: fix race between timeout and CPU hotplug
NVMe: Fix VPD B0 max sectors translation
There is no need for special handling of stripe-batches when the array
is degraded.
There may be if there is a failure in the batch, but STRIPE_DEGRADED
does not imply an error.
So don't set STRIPE_BATCH_ERR in ops_run_io just because the array is
degraded.
This actually causes a bug: the STRIPE_DEGRADED flag gets cleared in
check_break_stripe_batch_list() and so the bitmap bit gets cleared
when it shouldn't.
So in check_break_stripe_batch_list(), split the batch up completely -
again STRIPE_DEGRADED isn't meaningful.
Also don't set STRIPE_BATCH_ERR when there is a write error to a
replacement device. This simply removes the replacement device and
requires no extra handling.
Signed-off-by: NeilBrown <neilb@suse.de>
As the new 'scribble' array is sized based on chunk size,
we need to make sure the size matches the largest of 'old'
and 'new' chunk sizes when the array is undergoing reshape.
We also potentially need to resize it even when not resizing
the stripe cache, as chunk size can change without changing
number of devices.
So move the 'resize' code into a separate function, and
consider old and new sizes when allocating.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 46d5b785621a ("raid5: use flex_array for scribble data")
If any memory allocation in resize_stripes fails we will return
-ENOMEM, but in some cases we update conf->pool_size anyway.
This means that if we try again, the allocations will be assumed
to be larger than they are, and badness results.
So only update pool_size if there is no error.
This bug was introduced in 2.6.17 and the patch is suitable for
-stable.
Fixes: ad01c9e3752f ("[PATCH] md: Allow stripes to be expanded in preparation for expanding an array")
Cc: stable@vger.kernel.org (v2.6.17+)
Signed-off-by: NeilBrown <neilb@suse.de>
