For processors that have more than 64 TLBs, we need to decode both
config1 and config4 to determine the total number TLBs.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS currently lacks the readl_be and writel_be accessors
which are required by BCM63xx for OHCI and EHCI support.
Let's define them globally for MIPS. This also fixes the
compilation of the bcm63xx defconfig against USB.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Patchwork: http://patchwork.linux-mips.org/patch/793/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In order to achieve correct synchronization semantics, the Octeon port
had defined CONFIG_WEAK_REORDERING_BEYOND_LLSC. This resulted in code
that looks like:
sync
ll ...
.
.
.
sc ...
.
.
sync
The second SYNC was redundant, but harmless.
Octeon has a SYNCW instruction that acts as a write-memory-barrier
(due to an erratum in some parts two SYNCW are used). It is much
faster than SYNC because it imposes ordering on the writes, but
doesn't otherwise stall the execution pipeline. On Octeon, SYNC
stalls execution until all preceeding writes are committed to the
coherent memory system.
Using:
syncw;syncw
ll
.
.
.
sc
.
.
Has identical semantics to the first sequence, but is much faster.
The SYNCW orders the writes, and the SC will not complete successfully
until the write is committed to the coherent memory system. So at the
end all preceeding writes have been committed. Since Octeon does not
do speculative reads, this functions as a full barrier.
The patch removes CONFIG_WEAK_REORDERING_BEYOND_LLSC, and substitutes
SYNCW for SYNC in write-memory-barriers.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/850/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace some instances of smp_llsc_mb() with a new macro
smp_mb__before_llsc(). It is used before ll/sc sequences that are
documented as needing write barrier semantics.
The default implementation of smp_mb__before_llsc() is just smp_llsc_mb(),
so there are no changes in semantics.
Also simplify definition of smp_mb(), smp_rmb(), and smp_wmb() to be just
barrier() in the non-SMP case.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/851/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The smp_llsc_rmb() and smp_llsc_wmb() macros are not used in the tree,
remove them.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For 64-bit kernels with 64KB pages and two level page tables, there are
42 bits worth of virtual address space This is larger than the 40 bits of
virtual address space obtained with the default 4KB Page size and three
levels, so there are no draw backs for using two level tables with this
configuration.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/761/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the GPIO config symbol to only build Au1000 interrupt code on chips with
compatible hw.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/670/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the cpu subtype cpp macros in favor of runtime detection,
to improve compile coverage of the alchemy common code.
(Increases kernel size by 700 bytes).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/699/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes the board code register the au1000-eth platform device. The
au1000-eth platform data can be overriden with the au1xxx_override_eth_cfg
function like it has to be done for the Bosporus board which uses a
different MAC/PHY setup.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: David Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/618/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Create own directory for DB1200 code and update it with new features.
- SPI support:
- tmp121 temperature sensor
- SPI flash on DB1200
- I2C support
- NE1619 sensor
- AT24 eeprom
- I2C/SPI can be selected at boot time via switch S6.8
- Carddetect IRQs for SD cards.
- gen_nand based NAND support.
- hexleds count sleep/wake transitions.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove unused uart bit definitions and base macros.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch replaces the general alchemy prom_putchar() implementation
in favor of board-specific versions: The UART where the output of
prom_putchar is directed to really depends on the board, the current
implementation hardcodes this on a per-SoC basis which is just wrong.
So a generic uart tx function is provided in the alchemy headers,
and the boards can provide their own prom_putchar with custom
destination uart, and all in-kernel alchemy boards support
early printk.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.
(Queueing function signature has changed in order to give
a build failure instead of silent functional changes due
to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Eliminate the sharing of IRQ names among the differenct Alchemy
variants. IRQ numbers need no longer be hidden behind a
CONFIG_SOC_AU1XXX symbol: step 1 in my quest to make the Alchemy
code less reliant on a hardcoded subtype.
This patch also renames the GPIO irq number constants. It's really
an interrupt line, NOT a GPIO number!
Code which relied on certain irq numbers to have the same name
across all supported cpu subtypes is changed to determine current
cpu subtype at runtime; in some places this isn't possible so
a "compat" symbol is used.
Run-tested on DB1200.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register the PCMCIA driver on all boards supported by it,
get rid of now-unused pcmcia macros in the board headers
(and subsequently empty pb1100/pb1500 ones).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
- supports Db1000, DB/PB1100/1500/1550/1200.
- support for carddetect and statuschange IRQs.
- pcmcia socket mem/io/attr areas and irqs passed through
platform resource information.
- doesn't freeze system during card insertion/ejection like
the one it replaces.
- boardtype is automatically detected using BCSR ID register.
Run-tested on the DB1200.
Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
remove board_init_irq(): On all in-kernel boards it is sufficient to
initialize board interrupts in an arch_initcall by using the default
linux irq functions.
Some small irqmap.c files have been folded into board_setup files.
Run-tested on DB1200; compile-tested on all other affected boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the PB1200 IRQ cascade code out to the BCSR support code:
upcoming DB1300 support can use it too.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On VIVT ARM, when we have multiple shared mappings of the same file
in the same MM, we need to ensure that we have coherency across all
copies. We do this via make_coherent() by making the pages
uncacheable.
This used to work fine, until we allowed highmem with highpte - we
now have a page table which is mapped as required, and is not available
for modification via update_mmu_cache().
Ralf Beache suggested getting rid of the PTE value passed to
update_mmu_cache():
On MIPS update_mmu_cache() calls __update_tlb() which walks pagetables
to construct a pointer to the pte again. Passing a pte_t * is much
more elegant. Maybe we might even replace the pte argument with the
pte_t?
Ben Herrenschmidt would also like the pte pointer for PowerPC:
Passing the ptep in there is exactly what I want. I want that
-instead- of the PTE value, because I have issue on some ppc cases,
for I$/D$ coherency, where set_pte_at() may decide to mask out the
_PAGE_EXEC.
So, pass in the mapped page table pointer into update_mmu_cache(), and
remove the PTE value, updating all implementations and call sites to
suit.
Includes a fix from Stephen Rothwell:
sparc: fix fallout from update_mmu_cache API change
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linux kernel 2.6.32 and later allocate address space from the top of the
kernel virtual memory address space.
This patch implements virtual memory size detection for 64 bit MIPS CPUs
to avoid resulting crashes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/935/
Reviewed-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
DBDMA descriptors need to be located at 32-byte aligned addresses;
however kmalloc in conjunction with the SLAB allocator and
CONFIG_DEBUG_SLUB enabled doesn't deliver any. The dbdma code works
around that by allocating a larger area and realigning the start
address within it.
When freeing a channel however this adjustment is not taken into
account which results in an oops:
Kernel bug detected[#1]:
[...]
Call Trace:
[<80186010>] cache_free_debugcheck+0x284/0x318
[<801869d8>] kfree+0xe8/0x2a0
[<8010b31c>] au1xxx_dbdma_chan_free+0x2c/0x7c
[<80388dc8>] au1x_pcm_dbdma_free+0x34/0x4c
[<80388fa8>] au1xpsc_pcm_close+0x28/0x38
[<80383cb8>] soc_codec_close+0x14c/0x1cc
[<8036dbb4>] snd_pcm_release_substream+0x60/0xac
[<8036dc40>] snd_pcm_release+0x40/0xa0
[<8018c7a8>] __fput+0x11c/0x228
[<80188f60>] filp_close+0x7c/0x98
[<80189018>] sys_close+0x9c/0xe4
[<801022a0>] stack_done+0x20/0x3c
Fix this by recording the address delivered by kmalloc() and using
it as parameter to kfree().
This fix is only necessary with the SLAB allocator and CONFIG_DEBUG_SLAB
enabled; non-debug SLAB, SLUB do return nicely aligned addresses,
debug-enabled SLUB currently panics early in the boot process.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/878/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS processor is limited to 64 external interrupt sources. Using a
greater number without IRQ sharing requires reading platform-specific
registers. On such platforms, reading the IntCtl register to determine
which interrupt corresponds to a timer interrupt will not work.
On MIPSR2 systems there is a solution - the TI bit in the Cause register,
specifically indicates that a timer interrupt has occured. This patch uses
that bit to detect interrupts for MIPSR2 processors, which may be expected
to work regardless of how the timer interrupt may be routed in the hardware.
Signed-off-by: David VomLehn (dvomlehn@cisco.com)
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/804/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pre-compute addresses for the basic ASIC registers. This speeds up access
and allows memory for unused configurations to be freed. In addition,
uninitialized register addresses will be returned as NULL to catch bad
usage quickly.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/806/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
pcibus_to_node can return -1 if we cannot determine which node a pci bus
is on. If passed -1, cpumask_of_node will negatively index the lookup array
and pull in random data:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
00000000,00000003,00000000,00000000
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
64-65
Change cpumask_of_node to check for -1 and return cpu_all_mask in this
case:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
ffffffff,ffffffff,ffffffff,ffffffff
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
0-127
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Patchwork: http://patchwork.linux-mips.org/patch/831/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (71 commits)
MIPS: Lasat: Fix botched changes to sysctl code.
RTC: rtc-cmos.c: Fix warning on MIPS
MIPS: Cleanup random differences beween lmo and Linus' kernel.
MIPS: No longer hardwire CONFIG_EMBEDDED to y
MIPS: Fix and enhance built-in kernel command line
MIPS: eXcite: Remove platform.
MIPS: Loongson: Cleanups of serial port support
MIPS: Lemote 2F: Suspend CS5536 MFGPT Timer
MIPS: Excite: move iodev_remove to .devexit.text
MIPS: Lasat: Convert to proc_fops / seq_file
MIPS: Cleanup signal code initialization
MIPS: Modularize COP2 handling
MIPS: Move EARLY_PRINTK to Kconfig.debug
MIPS: Yeeloong 2F: Cleanup reset logic using the new ec_write function
MIPS: Yeeloong 2F: Add LID open event as the wakeup event
MIPS: Yeeloong 2F: Add basic EC operations
MIPS: Move several variables from .bss to .init.data
MIPS: Tracing: Make function graph tracer work with -mmcount-ra-address
MIPS: Tracing: Reserve $12(t0) for mcount-ra-address of gcc 4.5
MIPS: Tracing: Make ftrace for MIPS work without -fno-omit-frame-pointer
...
Proper Posix O_SYNC handling only made it into 2.6.33, not 2.6.32.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-33' of git://repo.or.cz/linux-kbuild: (29 commits)
net: fix for utsrelease.h moving to generated
gen_init_cpio: fixed fwrite warning
kbuild: fix make clean after mismerge
kbuild: generate modules.builtin
genksyms: properly consider EXPORT_UNUSED_SYMBOL{,_GPL}()
score: add asm/asm-offsets.h wrapper
unifdef: update to upstream revision 1.190
kbuild: specify absolute paths for cscope
kbuild: create include/generated in silentoldconfig
scripts/package: deb-pkg: use fakeroot if available
scripts/package: add KBUILD_PKG_ROOTCMD variable
scripts/package: tar-pkg: use tar --owner=root
Kbuild: clean up marker
net: add net_tstamp.h to headers_install
kbuild: move utsrelease.h to include/generated
kbuild: move autoconf.h to include/generated
drop explicit include of autoconf.h
kbuild: move compile.h to include/generated
kbuild: drop include/asm
kbuild: do not check for include/asm-$ARCH
...
Fixed non-conflicting clean merge of modpost.c as per comments from
Stephen Rothwell (modpost.c had grown an include of linux/autoconf.h
that needed to be changed to generated/autoconf.h)
The platform has never been fully merged
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
This patchs uses a loongson_uart_base variable instead of the
uart_base[] array and adds a new kernel option to avoid to compile
uart_base.c all the time, which will save a little bit of memory for us.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.orghttp://patchwork.linux-mips.org/patch/727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Away with the daemons of ifdef; get ready for future COP2 users.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/708/
Yeeloong 2F netbook has an KB3310B embedded controller to manage the LID
action. When the LID is closed or opened a SCI interrupt is sent out and
the corresponding event is saved to an EC register for later query.
Allow the LID open interrupt to wake the processor from wait mode if it is
in the suspend mode.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/685/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When remove the -fno-omit-frame-pointer, gcc will not save the frame
pointer for us, we need to save one ourselves.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/679/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch add a new section for MIPS to record the block of the hardirq
handling for function graph tracer(print_graph_irq) via adding the
__irq_entry annotation to the the entrypoints of the hardirqs(the block
with irq_enter()...irq_exit()).
Thanks goes to Steven & Frederic Weisbecker for their feedbacks.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/676/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With dynamic function tracer, by default, _mcount is defined as an
"empty" function, it returns directly without any more action . When
enabling it in user-space, it will jump to a real tracing
function(ftrace_caller), and do the real job for us.
Differ from the static function tracer, dynamic function tracer provides
two functions ftrace_make_call()/ftrace_make_nop() to enable/disable the
tracing of some indicated kernel functions(set_ftrace_filter).
In the -v4 version, the implementation of this support is basically the same as
X86 version does: _mcount is implemented as an empty function and ftrace_caller
is implemented as a real tracing function respectively.
But in this version, to support module tracing with the help of
-mlong-calls in arch/mips/Makefile:
MODFLAGS += -mlong-calls.
The stuff becomes a little more complex. We need to cope with two
different type of calling to _mcount.
For the kernel part, the calling to _mcount(result of "objdump -hdr
vmlinux"). is like this:
108: 03e0082d move at,ra
10c: 0c000000 jal 0 <fpcsr_pending>
10c: R_MIPS_26 _mcount
10c: R_MIPS_NONE *ABS*
10c: R_MIPS_NONE *ABS*
110: 00020021 nop
For the module with -mlong-calls, it looks like this:
c: 3c030000 lui v1,0x0
c: R_MIPS_HI16 _mcount
c: R_MIPS_NONE *ABS*
c: R_MIPS_NONE *ABS*
10: 64630000 daddiu v1,v1,0
10: R_MIPS_LO16 _mcount
10: R_MIPS_NONE *ABS*
10: R_MIPS_NONE *ABS*
14: 03e0082d move at,ra
18: 0060f809 jalr v1
In the kernel version, there is only one "_mcount" string for every
kernel function, so, we just need to match this one in mcount_regex of
scripts/recordmcount.pl, but in the module version, we need to choose
one of the two to match. Herein, I choose the first one with
"R_MIPS_HI16 _mcount".
and In the kernel verion, without module tracing support, we just need
to replace "jal _mcount" by "jal ftrace_caller" to do real tracing, and
filter the tracing of some kernel functions via replacing it by a nop
instruction.
but as we have described before, the instruction "jal ftrace_caller" only left
32bit length for the address of ftrace_caller, it will fail when calling from
the module space. so, herein, we must replace something else.
the basic idea is loading the address of ftrace_caller to v1 via changing these
two instructions:
lui v1,0x0
addiu v1,v1,0
If we want to enable the tracing, we need to replace the above instructions to:
lui v1, HI_16BIT_ftrace_caller
addiu v1, v1, LOW_16BIT_ftrace_caller
If we want to stop the tracing of the indicated kernel functions, we
just need to replace the "jalr v1" to a nop instruction. but we need to
replace two instructions and encode the above two instructions
oursevles.
Is there a simpler solution? Yes! Here it is, in this version, we put _mcount
and ftrace_caller together, which means the address of _mcount and
ftrace_caller is the same:
_mcount:
ftrace_caller:
j ftrace_stub
nop
...(do real tracing here)...
ftrace_stub:
jr ra
move ra, at
By default, the kernel functions call _mcount, and then jump to ftrace_stub and
return. and when we want to do real tracing, we just need to remove that "j
ftrace_stub", and it will run through the two "nop" instructions and then do
the real tracing job.
what about filtering job? we just need to do this:
lui v1, hi_16bit_of_mcount <--> b 1f (0x10000004)
addiu v1, v1, low_16bit_of_mcount
move at, ra
jalr v1
nop
1f: (rec->ip + 12)
In linux-mips64, there will be some local symbols, whose name are
prefixed by $L, which need to be filtered. thanks goes to Steven for
writing the mips64-specific function_regex.
In a conclusion, with RISC, things becomes easier with such a "stupid"
trick, RISC is something like K.I.S.S, and also, there are lots of
"simple" tricks in the whole ftrace support, thanks goes to Steven and
the other folks for providing such a wonderful tracing framework!
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/675/
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If -pg of gcc is enabled with CONFIG_FUNCTION_TRACER=y. a calling to
_mcount will be inserted into each kernel function. so, there is a
possibility to trace the kernel functions in _mcount.
This patch add the MIPS specific _mcount support for static function
tracing. by default, ftrace_trace_function is initialized as
ftrace_stub(an empty function), so, the default _mcount will introduce
very little overhead. after enabling ftrace in user-space, it will jump
to a real tracing function and do static function tracing for us.
and -ffunction-sections is incompatible with -pg, so, disable it when
ftracer is enabled.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/672/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson 2F supports CPU clock scaling. When put it into wait mode by
setting the frequency as ZERO it will stay in this mode until an external
interrupt wakes the CPU again.
To enable clock scaling support, an external timer of a known stable rate
is required.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cpufreq@vger.kernel.org,
Cc: Dave Jones <davej@redhat.com>,
Cc: Dominik Brodowski <linux@dominikbrodowski.net>,
Cc: yanh@lemote.com
Cc: huhb@lemote.com,
Patchwork: http://patchwork.linux-mips.org/patch/660/
Patchwork: http://patchwork.linux-mips.org/patch/751/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CPUFreq support for Loongson 2F requires an external timer.
Because the frequency of the MIPS Timer is related to the CPU frequency
which itself is variable another timer of constant frequency is required.
Export the mfgpt0 counter disable / enable operations for the coming
suspend support to suspend / resume the timer.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cpufreq@vger.kernel.org,
Cc: Dave Jones <davej@redhat.com>,
Cc: Dominik Brodowski <linux@dominikbrodowski.net>,
Cc: yanh@lemote.com
Cc: huhb@lemote.com,
Patchwork: http://patchwork.linux-mips.org/patch/658/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Kernel support for this machine is almost the same as Fuloong 2F; the only
difference is that it uses the serial port provided by Loongson 2F processor
as Yeeloong 2F does.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/656/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the Cisco Powertv cable settop box to the MIPS tree. This platform is
based on a MIPS 24Kc processor with various devices integrated on the same
ASIC. There are multiple models of this box, with differing configuration
but the same kernel runs across the product line.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/132/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds two new kernel options: CPU_SUPPORTS_CPUFREQ and
CPU_SUPPORTS_ADDRWINCFG to describe the new features of Loongons 2F and
replaces the several ugly #if clauses by them.
These two options will be utilized by the future loongson revisions and
related drivers such as the coming Loongson 2F CPUFreq driver.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Lemote Loongson 2F family machines use CS5536 as their south bridge and need
these lowlevel interfaces to access the devices on CS5536.
Virtualize the legacy devices on CS5536 as PCI devices. This way users can
access the CS5536 PCI config space directly as a normal multi-function
PCI 2.2 device.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: zhangfx@lemote.com
Cc: yanh@lemote.com
Cc: huhb@lemote.com
Cc: Nicholas Mc Guire <hofrat@hofr.at>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: loongson-dev@googlegroups.com
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a new kernel option for Lemote Loongson 2F family machines.
Lemote loongson2f family machines utilize the 2f revision of loongson
processor and the AMD CS5536 south bridge.
Family members include Fuloong 2F mini PC, Yeeloong 2F notebook, LingLoong
all-in-one PC and others.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: zhangfx@lemote.com
Cc: yanh@lemote.com
Cc: huhb@lemote.com
Cc: Nicholas Mc Guire <hofrat@hofr.at>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: loongson-dev@googlegroups.com
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson 2F has built-in DDR2 and PCI-X controller. The PCI-X controller
has a programming interface similiar to the the FPGA northbridge used on
Loongson 2E.
The main differences between Loongson 2E and Loongson 2F include:
1. Loongson 2F has an extra address window configuration module, which
is used to map CPU address space to DDR or PCI address space, or map
the PCI-DMA address space to DDR or LIO address space.
2. Loongson 2F supports 8 levels of software configurable CPu frequency
which can be configured in the LOONGSON_CHIPCFG0 register. The coming
cpufreq and standby support are based on this feature.
Loongson.h abstracts the modules and corresponding methods are abstracted.
Add other Loongson-2F-specific source code including gcc 4.4 support, PCI
memory space, PCI IO space, DMA address.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To share the same kernel image amon different machines we have added the
machtype command line support.
In the old serial port implementation the UART base address is hardcoded as
a macro in machine.h which breaks with machtype, so change that to discover
the address dynamically. Also move the initialization of the UART base
address to uart_base.c to avoid remapping twice for early_printk.c and
serial.c.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/581/
Patchwork: http://patchwork.linux-mips.org/patch/682/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To choose code for different machines by the value of machtype it needs to
be initialized as early as possible. So move initialization of
mips_machtype to prom_init().
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On SMP systems, the collection of statistics can cause cache line
bouncing in the lines associated with the counters. Also there are
races incrementing the counters on multiple CPUs.
To fix both problems, we collect the statistics in per-CPU variables,
and add them up in the debugfs read operation.
As a test I ran the LTP float_bessel test on a 12 CPU Octeon system.
Without CONFIG_DEBUG_FS : 2602 seconds.
With CONFIG_DEBUG_FS: 2640 seconds.
With non-cpu-local atomic statistics: 14569 seconds.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The built-in Loongson 2E/2F northbridge in is bonito64-compatible but not
identical with it. To avoid influencing the original bonito64 support and
make the loongson support more maintainable, it's better to separate the
Bonito64 code from the Loongson code.
This also prepares the kernel for the coming Loongson 2f machines family
support.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: yanh@lemote.com
Cc: huhb@lemote.com
Cc: Zhang Le <r0bertz@gentoo.org>
Cc: zhangfx@lemote.com,
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Processors that support the mips64r2 ISA can in four instructions
convert a shifted PGD pointer stored in the upper bits of c0_context
into a usable pointer. By doing this we save a memory load and
associated potential cache miss in the TLB exception handlers.
Since the upper bits of c0_context were holding the CPU number, we
move this to the upper bits of c0_xcontext which doesn't have enough
bits to hold the PGD pointer, but has plenty for the CPU number.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Octeon SOC has two types of Ethernet ports, each type with its own
driver. However, the PHYs for all the ports are controlled by a
common MDIO bus. Because the mdio driver is not associated with a
particular driver, but is instead a system level resource, we create s
stand-alone driver for it.
As for the driver, we put the register definitions in
arch/mips/include/asm/octeon where most of the other Octeon register
definitions live. This is a platform driver with the platform device
for "mdio-octeon" being registered in the platform startup code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS-specific macro CL_SIZE is merely aliasing the macro
COMMAND_LINE_SIZE. Other architectures use the latter; also,
COMMAND_LINE_SIZE is documented in kernel-parameters.txt, so
let's use it, and remove the alias.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nobody is using the ARCS-specific prom_getcmdline(), so let's remove it.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently all architectures but microblaze unconditionally define
USE_ELF_CORE_DUMP. The microblaze omission seems like an error to me, so
let's kill this ifdef and make sure we are the same everywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: <linux-arch@vger.kernel.org>
Cc: Michal Simek <michal.simek@petalogix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Name space cleanup for rwlock functions. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
Not strictly necessary for -rt as -rt does not have non sleeping
rwlocks, but it's odd to not have a consistent naming convention.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
Name space cleanup. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
Further name space cleanup. No functional change
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
The raw_spin* namespace was taken by lockdep for the architecture
specific implementations. raw_spin_* would be the ideal name space for
the spinlocks which are not converted to sleeping locks in preempt-rt.
Linus suggested to convert the raw_ to arch_ locks and cleanup the
name space instead of using an artifical name like core_spin,
atomic_spin or whatever
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
The simplest method was to add an extra asm-offsets.h
file in arch/$ARCH/include/asm that references the generated file.
We can now migrate the architectures one-by-one to reference
the generated file direct - and when done we can delete the
temporary arch/$ARCH/include/asm/asm-offsets.h file.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michal Marek <mmarek@suse.cz>
While Linux provided an O_SYNC flag basically since day 1, it took until
Linux 2.4.0-test12pre2 to actually get it implemented for filesystems,
since that day we had generic_osync_around with only minor changes and the
great "For now, when the user asks for O_SYNC, we'll actually give
O_DSYNC" comment. This patch intends to actually give us real O_SYNC
semantics in addition to the O_DSYNC semantics. After Jan's O_SYNC
patches which are required before this patch it's actually surprisingly
simple, we just need to figure out when to set the datasync flag to
vfs_fsync_range and when not.
This patch renames the existing O_SYNC flag to O_DSYNC while keeping it's
numerical value to keep binary compatibility, and adds a new real O_SYNC
flag. To guarantee backwards compatiblity it is defined as expanding to
both the O_DSYNC and the new additional binary flag (__O_SYNC) to make
sure we are backwards-compatible when compiled against the new headers.
This also means that all places that don't care about the differences can
just check O_DSYNC and get the right behaviour for O_SYNC, too - only
places that actuall care need to check __O_SYNC in addition. Drivers and
network filesystems have been updated in a fail safe way to always do the
full sync magic if O_DSYNC is set. The few places setting O_SYNC for
lower layers are kept that way for now to stay failsafe.
We enforce that O_DSYNC is set when __O_SYNC is set early in the open path
to make sure we always get these sane options.
Note that parisc really screwed up their headers as they already define a
O_DSYNC that has always been a no-op. We try to repair it by using it for
the new O_DSYNC and redefinining O_SYNC to send both the traditional
O_SYNC numerical value _and_ the O_DSYNC one.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jan Kara <jack@suse.cz>
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers, init: Limit the number of per cpu calibration bootup messages
posix-cpu-timers: optimize and document timer_create callback
clockevents: Add missing include to pacify sparse
x86: vmiclock: Fix printk format
x86: Fix printk format due to variable type change
sparc: fix printk for change of variable type
clocksource/events: Fix fallout of generic code changes
nohz: Allow 32-bit machines to sleep for more than 2.15 seconds
nohz: Track last do_timer() cpu
nohz: Prevent clocksource wrapping during idle
nohz: Type cast printk argument
mips: Use generic mult/shift factor calculation for clocks
clocksource: Provide a generic mult/shift factor calculation
clockevents: Use u32 for mult and shift factors
nohz: Introduce arch_needs_cpu
nohz: Reuse ktime in sub-functions of tick_check_idle.
time: Remove xtime_cache
time: Implement logarithmic time accumulation
* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block: (113 commits)
cfq-iosched: Do not access cfqq after freeing it
block: include linux/err.h to use ERR_PTR
cfq-iosched: use call_rcu() instead of doing grace period stall on queue exit
blkio: Allow CFQ group IO scheduling even when CFQ is a module
blkio: Implement dynamic io controlling policy registration
blkio: Export some symbols from blkio as its user CFQ can be a module
block: Fix io_context leak after failure of clone with CLONE_IO
block: Fix io_context leak after clone with CLONE_IO
cfq-iosched: make nonrot check logic consistent
io controller: quick fix for blk-cgroup and modular CFQ
cfq-iosched: move IO controller declerations to a header file
cfq-iosched: fix compile problem with !CONFIG_CGROUP
blkio: Documentation
blkio: Wait on sync-noidle queue even if rq_noidle = 1
blkio: Implement group_isolation tunable
blkio: Determine async workload length based on total number of queues
blkio: Wait for cfq queue to get backlogged if group is empty
blkio: Propagate cgroup weight updation to cfq groups
blkio: Drop the reference to queue once the task changes cgroup
blkio: Provide some isolation between groups
...
Use the new unreachable() macro instead of while(1);
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Jean-Mickael Guerin <jean-mickael.guerin@6wind.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Joseph S. Myers for reporting this.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Joseph S. Myers" <joseph@codesourcery.com>
Patchwork: http://patchwork.linux-mips.org/patch/723/
If __xchg() is not getting inlined the outline version of the function
will have a reference to __xchg_called_with_bad_pointer() which does not
exist remaining. Fixed by using BUILD_BUG_ON() to check for allowable
operand sizes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/705/
Mtdblock driver doesn't call flush_dcache_page for pages in request. So,
this causes problems on architectures where the icache doesn't fill from
the dcache or with dcache aliases. The patch fixes this.
The ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE symbol was introduced to avoid
pointless empty cache-thrashing loops on architectures for which
flush_dcache_page() is a no-op. Every architecture was provided with this
flush pages on architectires where ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE is
equal 1 or do nothing otherwise.
See "fix mtd_blkdevs problem with caches on some architectures" discussion
on LKML for more information.
Signed-off-by: Ilya Loginov <isloginov@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Peter Horton <phorton@bitbox.co.uk>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Replace the MIPS functions of mult/shift factor calculation for clock
events and clock sources with inline functions which call the generic
functions. The minimum guaranteed conversion range is set to 4 seconds
which corresponds to the current MIPS implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <20091111134229.807255074@linutronix.de>
The ohci-sm501 driver requires dma_declare_coherent_memory(). It is used
by the driver's local memory allocation with dma_alloc_coherent().
Tested on TANBAC TB0287(VR4131 + SM501).
[Ralf: Fixed reject in dma-default.c and removed the entire #if 0'ed block
in dma-mapping.h instead of just the #if 0.]
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson 2 does not have dcache aliases when is using 16k pages. and the
And because Loongson 2 doesn't do SMP , cpu_icache_snoops_remote_store does
not matter here.
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
set_saved_sp reads Context register. Avoid reading stale value from
earlier incomplete write.
Issue found and fixed for head.S by Chris Dearman <chris@mips.com>.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On an SMP system with cache aliases, the following sequence of events may
happen:
1) copy_user_highpage() runs on CPU0, invoking kmap_coherent() to create a
temporary mapping in the fixmap region
2) copy_page() starts on CPU0
3) CPU1 sends CPU0 an IPI asking CPU0 to run local_r4k_flush_cache_page()
4) CPU0 takes the interrupt, interrupting copy_page()
5) local_r4k_flush_cache_page() on CPU0 calls kmap_coherent() again
6) The second invocation of kmap_coherent() on CPU0 tries to use the
same fixmap virtual address that was being used by copy_user_highpage()
7) CPU0 throws a machine check exception for the TLB address conflict
Fixed by creating an extra set of fixmap entries for use in interrupt
handlers. This prevents fixmap VA conflicts between copy_user_highpage()
running in user context, and local_r4k_flush_cache_page() invoked from an
SMP IPI.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch checks if the watchdog enable bit is set in the DCL register
meaning that the hardware watchdog actually works and if so, register the
ar7_wdt platform_device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
