Packet DMA buffers are queued either initially all at once (then, a
queueing failure will cause firedtv to release the DMA context as a
whole) or subsequently one by one as they recycled after use (then a
failure is extremely unlikely). Therefore we can be a little less
cautious when counting at which packet buffer to set the interrupt flag.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cache only addresses of whole pages, not of each buffer chunk. Besides,
page addresses can be obtained by page_address() instead of kmap() since
they were allocated in lowmem.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add Prof 7301 PCI DVB-S2 card
The card based on stv0903 demod, stb6100 tuner.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The firedtv DVB driver will now work not only on top of the old ieee1394
driver stack but also on the new firewire driver stack.
Alongside to the firedtv-1394.c backend for driver binding and I/O, the
firedtv-fw.c backend is added. Depending on which of the two 1394
stacks is configured, one or the other or both backends will be built
into the firedtv driver.
This has been tested with a DVB-T and a DVB-C box on x86-64 and x86-32
together with a few different controllers (Agere FW323, a NEC chip, TI
TSB82AA2, TSB43AB22/A, VIA VT6306).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add #include <dvb_demux.h> for dvb_dmx_swfilter_packets(). This was
already indirectly included via firedtv.h, but don't rely on it.
The 4 bytes which were referred to as FIREWIRE_HEADER_SIZE are actually
the source packet header from IEC 61883-4 (MPEG2-TS data transmission
over 1394), not e.g. the IEEE 1394 isochronous packet header. So choose
a more precise name.
Also, express the payload size as a preprocessor constant too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Preparation for the port of firedtv to the firewire-core kernel API:
The fdtv->backend->lock() hook and thus the CMP code is slightly changed
to better fit with the new API.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Preparation for the port of firedtv to the firewire-core kernel API:
Canceling of the remote control workqueue job is factored into
firedtv-rc.c. Plus trivial whitespace change.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make id signed so we can't get an invalid pointer when we pass a negative
id.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Id: 55873
Add support for cxusb card Mygica D689 DBM-TH USB
Signed-off-by: David T. L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support for Maxim MAX2165 silicon tuner.
It was tested on Mygica X8558Pro, which has MAX2165, ATBM8830 and CX23885.
Signed-off-by: David T. L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID 1b80:e39d for Sveon STV20 Tuner USB DVB-T HDTV.
Signed-off-by: Ignacio de Miguel Diaz <imigueldiaz@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With a lower bandwidth setup, the Transport Stream gets corrupted due to
TSFIFO overrun. The patch fixes the issue.
The issue is seen with Transport Streams having a Symbol Rate of 22MSPS
and/or greater.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It had always the value 3 no matter what frequency was given.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While here, also do some blind scan related fixes.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch contains several fixes for the stv090x driver:
- added missing else
- use calculated timeout instead of fixed one
- use correct frequency when doing zigzag scan
- added missing read of GENCFG register
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch 4 of 4.
Also patch changes logic to prevent code repetitions and big indents.
It makes checkpatch silent :)
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch 3 of 4.
Also patch changes logic to prevent code repetitions and big indents.
It makes checkpatch silent :)
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch 2 of 4.
Also patch changes logic to prevent code repetitions and big indents.
It makes checkpatch silent :)
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch 1 of 4.
Also patch changes logic to prevent code repetitions and big indents.
It makes checkpatch silent :)
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It has positive effect for NetUP Dual DVB-S2 CI card.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On particularly weak signals, changing register 0xab after setting the
interleave mode will cause the FEC lock to get lost (while still holding the
EQ lock). So remove the write entirely, which seems to have had no adverse
effect in either of my ClearQAM environments (and in particular resolves the
customer's reported issue).
Also flip around the order of the amhum optimization and the interleave setup
to be consistent with the windows driver, which has the side-benefit of doing
them both in the same call (since the amhum optimization can only be done once
the interleave setup).
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sh51409 driver was only doing the QAM optimization a single time, and it
would only occur if you received a lock instantaneously after the tuning
request. Restructure the code so that the optimization occurs once you reach
a signal lock.
Note that this depends on the caller polling for status, but we don't have
much choice at this point without an independent thread monitoring the lock
status. Also, at this point pretty much every application polls for status
lock after doing the tune, so the likelihood of the optimization not occurring
in the real world is pretty low.
The state machine has also been reworked such that setting the interleave mode
is now a dependency of doing the QAM optimization. Before both were mutually
exclusive, which was not consistent with the Windows driver. We now have a
single state machine that controls both.
The changes as-is are only enabled for the HVR-1600. Once the changes are
tested with some of the other boards, this change should be made generic and
the "_legacy" functions should be removed.
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Perform some optimization of the register configuration based on a trace
of the HVR-1600 Windows i2c traffic (and consultation with Steven Toth).
Note that some of these values may be able to be moved into the common driver,
but I am holding off on that until they can be tested with other boards.
This work was sponsored by ONELAN Limited.
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
load smsdvb also for the hauppauge tiger cards
[dougsland@redhat.com: fixed rejects due changes in sms-cards.c]
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Acked-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes some fe->ops.X() functions which do nothing more useful than the default.
Signed-off-by: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes the driver return the correct DTV_DELIVERY_SYSTEM.
The driver previously returned SYS_UNDEFINED for DTV_DELIVERY_SYSTEM property,
as it lacked any driver specific S2API support.
Signed-off-by: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: add asm/div64.h and allocate vars only if dvb_demux_speedcheck specified]
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The variables are unsigned so the test `>= 0' is always true,
the `< 0' test always fails. In these cases the other part of
the test catches wrapped values.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for saturation/hue controls, prompted by errors showing up in
the mythbackend log.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looks like eeprom IR mode byte value 0x04 means there is remote
which should be polled. Patch enables polling also in case of 0x04.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for MSI DIGIVOX mini III remote.
Thanks to Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Thanks to Roman <lists@hasnoname.de>
Cc: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Cc: Roman <lists@hasnoname.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID 1b80:c161 for KWorld PlusTV DVB-T PCI Pro Card (DVB-T PC160-T).
Thanks to Andrew Cruickshank <atcrank@gmail.com> for reporting this.
Cc: Andrew Cruickshank <atcrank@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the dib7000p:
The status is HAS_LOCK only if the demod is able to decode the TPS. Sometimes, there is a TPS data lock, even if the demod is not able to decode it (ex: no RF signal).
For the STK7770P: correct value for the charge pump
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dib7000p/dib8000: added pid filtering
dib8000: the SNR is in 10th of dB (not in dB)
dib7000p and dib8000: added the pid filtering. This feature is enabled by module option (dvb-usb module).
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This IR uses NEC protocol. In order to use, dvb_usb_dib0700_ir_proto=0
should be used.
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, dvb_usb_dib0700_ir_proto is supported only with firmwares
older than 1.2. Adds support for it also with the newer firmware.
This is needed in order to support PixelView SBTVD IR.
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Address yet another regression introduced by the introduction of the zl10353
disable_i2c_gate field.
djh - I unmangled the patch which apparently got screwed up in the user's
email client.
Signed-off-by: Robert Lowery <rglowery@exemail.com.au>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When building for Sun 3:
drivers/built-in.o: In function `smscore_unregister_device':
drivers/media/dvb/siano/smscoreapi.c:723: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `smscore_register_device':
drivers/media/dvb/siano/smscoreapi.c:365: undefined reference to `dma_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch was generated by
git grep -E -i -l '[Aa]quire' | xargs -r perl -p -i -e 's/([Aa])quire/$1cquire/'
and the cumsumed was found by checking the diff for aquire.
Signed-off-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
something-bility is spelled as something-blity
so a grep for 'blit' would find these lines
this is so trivial that I didn't split it by subsystem / copy
additional maintainers - all changes are to comments
The only purpose is to get fewer false positives when grepping
around the kernel sources.
Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Which is why I have always preferred sizeof(struct foo) over
sizeof(var).
Cc: Antti Palosaari <crope@iki.fi>
Acked-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since 2.6.32(-rc1), DVB core checks the return value of
dvb_frontend_ops.set_frontend. Now it becomes apparent that firedtv
always returned a bogus value from its set_frontend method.
CC: stable@kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This solves a problem in firedtv that has become major for Swedish DVB-T
users the last month or so. It will most likely solve issues seen by
other users as well.
If the length of an AVC message is greater than 127, the length field
should be encoded in LV mode instead of V mode. V mode can only be used
if the length is 127 or less. This patch ensures that the CA_PMT
message is always encoded in LV mode so PMT message of greater lengths
can be supported.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for three new Hauppauge Device USB IDs:
2040:b900
2040:b910
2040:c000
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The lack of #include <linux/vmalloc.h> caused a compile error on some
architectures.
Signed-off-by: HIRANO Takahito <hiranotaka@zng.info>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixing kernel oops when driver attemps to load xc2028 firmware.
Note by djh: the patch contribute by Martin is a port of a fix I made during
the PCTV 340e development. It's a temporary workaround that fixes a regression
(an OOPS condition) and the real fix should be in the code that manages the
i2c master on the dib7000p. But this fix does address the immmediate
regression and should be merged upstream until we do a cleaner fix.
Signed-off-by: Martin Samek <martin@marsark.sytes.net>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
git commit db48138f6b changed by accident the
assignment of certain USB IDs to their device-specific-handlers.
Thanks to Edward Sheldrake for finding this regression
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
As reported by Ingo Molnar:
Here's another new build breakage that triggers in -tip testing:
drivers/built-in.o:(.data+0xb1f40): undefined reference to `dib0070_ctrl_agc_filter'
drivers/built-in.o:(.data+0xb1f80): undefined reference to `dib0070_ctrl_agc_filter'
triggers due to:
CONFIG_DVB_USB_DIB0700=y
CONFIG_DVB_TUNER_DIB0070 is not set
While working on a better approach, for now, let's just select tuner
dib0070 anytime we compile dib0700.
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As pointed by Marcin Slusarz <marcin.slusarz@gmail.com>, the warns happens
because CONFIG_DVB_MAX_ADAPTERS depends on CONFIG_DVB_CORE, and there are
valid configs where DVB_CORE is not selected.
This causes such warnings, for every V4L and common drivers that may or
may not be compiled with DVB support:
drivers/media/dvb/dvb-core/dvbdev.h:36:2: warning: #warning invalid CONFIG_DVB_MAX_ADAPTERS value
We can safely remove the warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
alpha:
drivers/media/dvb/pt1/pt1.c: In function 'pt1_cleanup_tables':
drivers/media/dvb/pt1/pt1.c:422: error: implicit declaration of function 'vfree'
drivers/media/dvb/pt1/pt1.c: In function 'pt1_init_tables':
drivers/media/dvb/pt1/pt1.c:431: error: implicit declaration of function 'vmalloc'
drivers/media/dvb/pt1/pt1.c:431: warning: assignment makes pointer from integer without a cast
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.
This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/media/dvb/pt1/pt1.c: In function ‘pt1_probe’:
drivers/media/dvb/pt1/pt1.c:915: warning: ‘DMA_nnBIT_MASK’ is deprecated
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds driver for 774 Friio White, ISDB-T USB receiver
Friio White is an USB 2.0 ISDB-T receiver. (http://www.friio.com/)
The device has a GL861 chip and a Comtech JDVBT90502 canned tuner module.
This driver ignores all the frontend_parameters except frequency,
as ISDB-T shares the same parameter configuration across the country
and thus the device can work like an intelligent one.
As this device does not include a CAM nor hardware descrambling feature,
the driver passes through scrambled TS streams.
There is Friio Black, a variant for ISDB-S, which shares the same USB
Vendor/Product ID with White, but it is not supported in this driver.
They should be identified in the initialization sequence,
but this feature is not tested.
Signed-off-by: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a driver for Earthsoft PT1
Eearthsoft PT1 is a PCI card for Japanese broadcasting with two ISDB-S
and ISDB-T demodulators.
This card has neither MPEG decoder nor conditional access module
onboard. It transmits only compressed and possibly encrypted MPEG data
over the PCI bus, so you need an external software decoder and a
decrypter to watch TV on your computer.
This driver is originally developed by Tomoaki Ishikawa
<tomy@users.sourceforge.jp> by reverse engineering.
[mchehab@redhat.com: renamed isdb_ts to isdbs_ts to use the current standard]
Signed-off-by: HIRANO Takahito <hiranotaka@zng.info>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In ISDB-S, time-devision duplex is used to multiplexing several waves
in the same frequency. Each wave is identified by its own transport
stream ID, or TS ID. We need to provide some way to specify this ID
from user applications to handle ISDB-S frontends.
This code has been tested with the Earthsoft PT1 driver.
[mchehab@infradead.org: Fix merge conflicts with isdbt and rename the new parameter to DTV_ISDBS_TS_ID]
Signed-off-by: HIRANO Takahito <hiranotaka@zng.info>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
increase BULK transfer size from 512 to 8192 to increase wakeups
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is fixing the initialization of the channel search parameters.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patchs adds support for the DiB8000 based devices STK807xP and
STK807xPVR to the dib0700-device-tree.
[mchehab@redhat.com: Fix merge conflicts]
Signed-off-by: Olivier Grenie <Olivier.Grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit adds support for the DiB8000 ISDB-T demodulator made by DiBcom.
Signed-off-by: Olivier Grenie <Olivier.Grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to follow a little bit the kernel coding style from now on
after the generation of that driver file and indent -linux call is
emitted.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
