clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA is enabled (with hardware flow control enabled) the FIFO size
must be set to the size of the DMA buffer, as this is the size the tty
subsystem can use.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MXS_AUART_DMA_CONFIG is originally used to check if the DT node
is configured with the DMA property.
But now, the MXS_AUART_DMA_CONFIG is set unconditionally in the
serial_mxs_probe_dt(), so the check in the mxs_auart_settermios() is
not necessary anymore. This patch removes this macro.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original DMA support works only when RTS/CTS is enabled.
(see the "e800163 serial: mxs-auart: add the DMA support for mx28")
But after several patches, DMA support has lost this limit.
(see the "bcc20f9 serial: mxs-auart: move to use generic DMA helper")
So an UART without the RTS/CTS lines may also enables the DMA support,
in which case the UART may gets unpredictable results.
This patch adds an optional property for the UART DT node
which indicates the UART has RTS and CTS lines, and it also means you
enable the DMA support for this UART.
This patch also adds a macro MXS_AUART_RTSCTS, and uses it to check
RTS/CTS before we enable the DMA for the UART.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this patch the driver waits ~1 ms for the UART to become idle. At
115200n8 this time is (theoretically) enough to transfer 11.5 characters
(= 115200 bits/s / (10 Bits/char) * 1ms). As the mxs-auart has a fifo size
of 16 characters the clock is gated too early. The problem is worse for
lower baud rates.
This only happens to really shut down the transmitter in the middle of a
transfer if /dev/ttyAPPx isn't opened in userspace (e.g. by a getty) but
was at least once (because the bootloader doesn't disable the transmitter).
So increase the timeout to 20 ms which should be enough for 9600n8, too.
Moreover skip gating the clock if the timeout is elapsed.
Cc: stable@vger.kernel.org # v2.6.39+
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The handler needs to ack the pending events before actually handling them.
Otherwise a new event might come in after it it considered non-pending or
handled and is acked then without being handled. So this event is only
noticed when the next interrupt happens.
Without this patch an i.MX28 based machine running an rt-patched kernel
regularly hangs during boot.
Cc: stable@vger.kernel.org # v2.6.39+
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the generic DMA device tree helper supported by mxs-dma driver,
client devices only need to call dma_request_slave_channel() for
requesting a DMA channel from dmaengine.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_string this time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detected by cppcheck:
[others/linux/drivers/tty/serial/mxs-auart.c:553]: (style) Same expression on both sides of '||'.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following warning when building with W=1 option:
drivers/tty/serial/mxs-auart.c: In function 'mxs_auart_tx_chars':
drivers/tty/serial/mxs-auart.c:272:10: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the patch "serial: mxs-auart: fix the wrong RTS hardware flow control" the
mainline mxs-uart driver now sets RTSEN only when hardware flow control is
enabled via software. It is not possible any longer to set RTS manually via
software. However, the manual modification is a valid operation.
Regain the possibility to set RTS via software and only set RTSEN when hardware
flow control is explicitly enabled via settermios cflag CRTSCTS.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should first unmap the DMA scatter list for receiving data, and
then copy the data from the DMA buffer.
The old code misses unmap the scatter list for RX. This patch fixes it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Tested-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the DMA is enabled, the Receive Timeout interrupt is very easy to be arised
in the 3M baud rate. The interrupt handler (aka mxs_auart_irq_handle) will call
mxs_auart_rx_chars() to handle the received data. This is not right, we can not
get the correct data from the RXFIFO now, the data have been moved to the
DMA buffer by the DMA engine.
This patch
(1) disables the Receive Timeout Interrupt when the DMA is enabled,
(2) and invoke the mxs_auart_rx_chars() only when the DMA is not enabled.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Tested-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only we meet the following conditions, we can enable the DMA support for
auart:
(1) We enable the DMA support in the dts file, such as
arch/arm/boot/dts/imx28.dtsi.
(2) We enable the hardware flow control.
(3) We use the mx28, not the mx23. Due to hardware bug(see errata: 2836),
we can not add the DMA support to mx23.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current mxs-auart driver is used for both mx23 and mx28.
But in mx23, the DMA has a bug(see errata:2836). We can not add the
DMA support in mx23, but we can add DMA support to auart in mx28.
So in order to add the DMA support for the auart in mx28, we should
distinguish the distinguish SOCs.
This patch adds a new platform_device_id table and a inline function
is_imx28_auart() to distinguish the mx23 and mx28.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mxs_auart_probe() gets the device by the get_device().
So we should put the device in the error path to balance the
device's reference counter.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We call the get_device() in the mxs_auart_probe().
For the balance of the reference count, we should put the
device in the mxs_auart_remove().
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After set the AUART_CTRL0_CLKGATE, the UART will gate all the clocks off.
So the following line will not take effect.
................................................................
writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
u->membase + AUART_INTR_CLR);
................................................................
To fix this issue, the patch moves this gate-off line to
the end of setting registers.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most of the time, the driver needs to check if the cts flow control
is enabled. But now, the driver checks the ASYNC_CTS_FLOW flag manually,
which is not a grace way. So add a new wraper function to make the code
tidy and clean.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without checking if the auart supports the hardware flow control or not,
the old mxs_auart_set_mctrl() asserted the RTS pin blindly.
This will causes the auart receives wrong data in the following case:
The far-end has already started the write operation, and wait for
the auart asserts the RTS pin. Then the auart starts the read operation,
but mxs_auart_set_mctrl() may be called before we set the RTSCTS in the
mxs_auart_settermios(). So the RTS pin is asserted in a wrong situation,
and we get the wrong data in the end.
This bug has been catched when I connect the mx23(DTE) to the mx53(DCE).
This patch also replaces the AUART_CTRL2_RTS with AUART_CTRL2_RTSEN.
We should use the real the hardware flow control, not the software-controled
hardware flow control.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big TTY/serial driver pull request for the 3.5-rc1 merge window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7rBoACgkQMUfUDdst+ykXsgCfeDKx6ZgLidYy3H40Y2Pt3XEO
TicAn1fcdGwOmMR/mowa+kTA68D/J6i2
=S7tG
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
Another simple series related to clock management, this time only for
imx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=czKE
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
clock management changes for i.MX
Another simple series related to clock management, this time only for
imx.
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: select HAVE_CLK_PREPARE for clock
clk: add config option HAVE_CLK_PREPARE into Kconfig
ASoC: mxs-saif: convert to clk_prepare/clk_unprepare
video: mxsfb: convert to clk_prepare/clk_unprepare
serial: mxs-auart: convert to clk_prepare/clk_unprepare
net: flexcan: convert to clk_prepare/clk_unprepare
mtd: gpmi-lib: convert to clk_prepare/clk_unprepare
mmc: mxs-mmc: convert to clk_prepare/clk_unprepare
dma: mxs-dma: convert to clk_prepare/clk_unprepare
net: fec: add clk_prepare/clk_unprepare
ARM: mxs: convert platform code to clk_prepare/clk_unprepare
clk: add helper functions clk_prepare_enable and clk_disable_unprepare
Fix up trivial conflicts in drivers/net/ethernet/freescale/fec.c due to
commit 0ebafefcaa ("net: fec: add clk_prepare/clk_unprepare") clashing
trivially with commit e163cc97f9 ("net/fec: fix the .remove code").
The patch converts mxs-auart driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
There is no need to call uart_write_wakeup after each character send.
Once at the end of the write sequence is enough.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do not include linux/device.h twice in drivers/tty/serial/mxs-auart.c .
Once is enough.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
