All unsuccessful (non-zero status) URBs were being dropped. After N_IN_URBs are
dropped you will no longer be able to receive data.
This patch resubmits unsuccessful URBs unless the status indicates that it should
be terminated. The statuses that indicate the URB should be terminated was
gathered from other similar drivers.
Signed-off-by: James Maki <jamescmaki@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
g_hid is a USB gadget driver implementing the Human Interface Device class
specification. The driver handles basic HID protocol handling in the
kernel, and allows userspace to read/write HID reports trough /dev/hidgX
character devices.
Signed-off-by: Fabien Chouteau <fabien.chouteau@barco.com>
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Generalise write buffer preparation.
This allows for drivers to manipulate (e.g. add headers) to bulk out
data before it is sent.
This adds a new function pointer to usb_serial_driver:
int (*prepare_write_buffer)(struct usb_serial_port *port,
void **dest, size_t size, const void *src, size_t count);
The function is generic and can be used with either kfifo-based or
multi-urb writes:
If *dest is NULL the implementation should allocate dest.
If src is NULL the implementation should use the port write fifo.
If not set, a generic implementation is used which simply uses memcpy or
kfifo_out.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use dynamic transfer buffer sizes since it is more efficient to let the
host controller do the partitioning to fit endpoint size. This way we
also do not use more than one urb per write request.
Replace max_in_flight_urbs with multi_urb_write flag in struct
usb_serial_driver to enable multi-urb writes.
Use MAX_TX_URBS=40 and a max buffer size of PAGE_SIZE to prevent DoS
attacks.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow drivers to implement their own multi-urb write bulk callbacks as
we do for single urb writes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the generic kfifo-based write implementation rather than allowing up
to 4000 8 byte urbs in the host stack queues.
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use usb_serial_generic_close to kill the read and write urbs and to
reset the write fifo.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Submit write urb if it is not already in use and we have buffered data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch to generic read implementation and use process_read_urb to do
device specific processing (handle line status).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow drivers to use the generic throttle and unthrottle implementation.
This makes sense for drivers using the generic read functionality.
Note that drivers need to set these explicitly in order to enable them
(i.e., we do not set them at port probe if not defined).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use generic read implementation and use process_read_urb to do device
specific processing (handle line status).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add process_read_urb to usb_serial_driver so that a driver can rely on
the generic read (and throttle) mechanism but still do device specific
processing of incoming data (such as adding tty_flags before pushing to
line discipline).
The default generic implementation handles sysrq for consoles but
otherwise simply pushes to tty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Always process and flush read urb, but only resubmit when not throttled.
The new tty-layer supply plenty of slack so there is really no need to
cache and delay processing of a single urb while throttled.
Note that unthrottle now submits using GFP_KERNEL as we are not in
atomic context (so there is no need to save irq state either).
Note also that the process_read_urb function could be added to
usb_serial_driver should any driver need to do any device specific
processing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need to initialise the read urb as this is done at port
probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The generic read and write bulk urbs are initialised when allocated in
usb_serial_probe. The only field that needs to be updated after that is
the transfer_buffer_length of the write urb.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the already exported function for submitting the read urb associated
with a usb_serial_port.
Make sure it returns the result of usb_submit_urb and rename to the
more descriptive usb_serial_generic_submit_read_urb.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Export usb_serial_generic_close so that drivers can easily kill the read
and write urb and make sure that the write fifo is reset.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On errors the fifo was reset without any locking. This could race with
write which do kfifo_put and perhaps also chars_in_buffer and write_room.
Every other access to the fifo is protected using the port lock so
better add it to the error path as well.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure chars_in_buffer accounts also for data in host stack queues.
This fixes the problem with tty_wait_until_sent returning too soon at
close which could cause the final write urb to be cancelled.
Reported-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pl2303 requires a bulk-in buffer larger than endpoint size to keep
up at high baudrates without loosing data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increase the bulk-out buffer size from 64 to 256 byte.
This gives a significant increase in throughput already at 1Mbaud as well
as lowered CPU usage. The buffer is big enough to keep up also at 3Mbaud
(128b would not suffice).
64b 256b
921k: 640 KB/s 870 KB/s
3M: 640 KB/s 2520 KB/s
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The cp210x requires a bulk-in buffer larger than endpoint size to keep
up at high baudrates without loosing data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increase the bulk-out buffer size from 64 to 256 byte.
This gives a significant increase in throughput already at 1Mbaud
(e.g. 710 instead of 640 KB/s) as well as lowered CPU usage.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow drivers to define custom bulk in/out buffer sizes in struct
usb_serial_driver. If not set, fall back to the default buffer size
which matches the endpoint size.
Three drivers are currently freeing the pre-allocated buffers and
allocating larger ones to achieve this at port probe (ftdi_sio) or even
at port open (ipaq and iuu_phoenix), which needless to say is suboptimal.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new quirk USB_QUIRK_HONOR_BNUMINTERFACES, when this quirk is
set and a device has more interface descriptors in a configuration
then it claims to have in config->bNumInterfaces, ignore all additional
interfaces.
This is needed for devices which try to hide unused interfaces by only
lowering config->bNumInterfaces, and which can't handle if you try to talk
to the "hidden" interfaces.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build error when CONFIG_MAGIC_SYSRQ is not enabled:
drivers/usb/serial/generic.c:566: error: implicit declaration of function 'handle_sysrq'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb console code has had a long standing problem of not being able
to pass the baud rate from the kernel argument console=ttyUSB0,BAUD
down to the initial tty open, unless you were willing to settle for
9600 baud.
The solution is to directly use tty_init_termios() in
usb_console_setup() as this will preserve any changes to the initial
termios setting on future opens.
CC: Alan Cox <alan@linux.intel.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"Static" buffers in fsg_buffhd structure (ie. fields which are arrays
rather then pointers to dynamically allocated memory) are not aligned
to any "big" power of two which may lead to poor DMA performance
(copying "by hand" of head or tail) or no DMA at all even if otherwise
hardware supports it.
Therefore, this patch makes mass storage function use kmalloc()ed
buffers which are (because of their size) page aligned (which should
be enough for any hardware).
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... and simplify the was we read/write from/to
DMA COUNT register.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
we can support the musb-specific test modes on the
vendor specific range of test selector as stated
on USB Specification Table 9-7 Test Mode Selectors.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
for now only a simple register dump entry (which can
be rather useful on debugging) and a way to start
test modes.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rather than hardcoding the gpio levels for vrsel, allow the platform
resources to handle this so boards can be active high or low.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the Makefile to build the
MUSB driver for OMAP4. It also sets the Kconfig
options for OMAP4.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Program the OTG_INTERFSEL register based on
transcevier type passed from board file.
Adapt signature of musb_platform_init() function
for davinci, blackfin and tusb6010.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
boards might want to optimize their fifo configuration
to the particular needs of that specific board. Allow
that by moving all related data structures to
<linux/usb/musb.h>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace all instances of using the console variable in struct
usb_serial_port with the struct tty_port version.
CC: Alan Cox <alan@linux.intel.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've been running variations of this patch for well over a year now;
my usual zoo of test devices didn't trigger any ill effects even
under heavy load. As a nice sideeffect idle-wakeups are reduced
from 20/s to about 2/s (EHCI hub with mouse and kbd).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1350) removes all usages of coherent buffers for USB
control-request setup-packet buffers. There's no good reason to
reserve coherent memory for these things; control requests are hardly
ever used in large quantity (the major exception is firmware
transfers, and they aren't time-critical). Furthermore, only seven
drivers used it. We might as well always use streaming DMA mappings
for setup-packet buffers, and remove some extra complexity from
usbcore.
The DMA-mapping portion of hcd.c is currently in flux. A separate
patch will be submitted to remove support for URB_NO_SETUP_DMA_MAP
after everything else settles down. The removal should go smoothly,
as by then nobody will be using it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1349b) clears up the confusion in many USB host
controller drivers between port features and port statuses. In mosty
cases it's true that the status bit is in the position given by the
corresponding feature value, but that's not always true and it's not
guaranteed in the USB spec.
There's no functional change, just replacing expressions of the form
(1 << USB_PORT_FEAT_x) with USB_PORT_STAT_x, which has the same value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1348) removes the bogus
USB_PORT_FEAT_{HIGHSPEED,SUPERSPEED} symbols from ch11.h. No such
features are defined by the USB spec. (There is a PORT_LOWSPEED
feature, but the spec doesn't mention it except to say that host
software should never use it.) The speed indicators are port
statuses, not port features.
As a temporary workaround for the xhci-hcd driver, a fictional
USB_PORT_STAT_SUPER_SPEED symbol is added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The compiler throws the following warning when compiling for a PowerPC 64
bit machine:
drivers/usb/storage/isd200.c:580: warning: the frame size of 2208 bytes is larger than 2048 bytes
There is a struct scsi_device which is placed on the stack and is
largely responsible for such wastage. The struct is just a dummy struct
filled with NULLs and set as the scsi_cmnd->device to make the
usb_stor_Bulk_transport function happy.
This patch makes the struct static, so that it is never placed onto the
stack and silences the compiler warning.
Signed-off-by: Ian Munsie <imunsie@au.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Seems to me that BKL is not needed here because necessary locking is already
provided by mutex sisusb->lock.
Also change the returned value to long.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
