we are getting struct clk using clk_get before calling
clk_prepare_enable. but if clk_prepare_enable fails, then we are
jumping to fail_mutex_unlock where we are just unlocking the mutex,
but we are not freeing the clock source.
this patch just adds a call to clk_put before jumping to
fail_mutex_unlock.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add array controls to test support for such controls. There is one
array with just one element, one 8x16 matrix control and one 4 dimensional
2x3x4x5 control.
This makes it possible to experiment with such controls without requiring
hard-to-get hardware.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support for vidioc_create_bufs. Along side
remove unneeded member numbuffers.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Needed due to some important regression fixes at RC core.
* commit 'v3.18-rc4': (587 commits)
Linux 3.18-rc4
ARM: dts: zynq: Enable PL clocks for Parallella
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
USB: Update default usb-storage delay_use value in kernel-parameters.txt
sysfs: driver core: Fix glue dir race condition by gdp_mutex
MIPS: Fix build with binutils 2.24.51+
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
USB: cdc-acm: add quirk for control-line state requests
tty: Fix pty master poll() after slave closes v2
MIPS: R3000: Fix debug output for Virtual page number
...
Conflicts:
drivers/media/rc/rc-main.c
Both sides of these assignments actually have type "const struct
vb2_mem_ops *", so the casts are unnecessary and slightly confusing.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If alloc_workqueue() fails, we should go to the 'err_v4l2_register' label, which
will unregister the v4l2 device.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of calling v4l2_device_unregister() in multiple locations within the
error paths, let's call it from a single location to make the error handling
simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The default used to be that the first vivid device instance was
single planar, the second multi planar, the third single planar, etc.
However, that turned out to be unexpected and awkward. Change the
driver to always default to single planar.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the use of nested functions where a normal function will suffice.
Nested functions are not liked by upstream kernel developers in general. Their
use breaks the use of clang as a compiler, and doesn't make the code any
better.
This code now works for both gcc and clang.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Behan Webster <behanw@converseincode.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support for returning -ENODATA if the current
output doesn't support it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch groups the v4l2_ioctl_ops.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch uses vb2_is_busy() helper to check if streaming is
actually started, instead of driver managing it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support for using vb2_ioctl_* helpers.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch converts the driver to use fh handling provided by the
v4l core instead of driver doing it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch improve vpbe_buffer_prepare() callback, as buf_prepare()
callback is never called with invalid state and check for
vb2_plane_vaddr(vb, 0) is dropped as payload check should
be done unconditionally.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch drops buf_cleanup() callback as this callback
is never called with buffer state active.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch makes use of vb2_ops_wait_prepare/finish helper functions.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch drops the buf_init() callback as init
of buf list is not required.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch moves the initialization of vb2 queue and the DMA
context to probe() and clean up in remove() callback respectively.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The NV12M is supported by all the version of MFC, so it is better
to use it as default OUTPUT format.
MFC v5 doesn't support NV21, I have tested it, for the SEC doc
it is not supported either.
Signed-off-by: ayaka <ayaka@soulik.info>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Patch b906352c23 ([media] coda: dequeue buffers if start_streaming fails)
incorrectly marked buffers as DEQUEUED in case of start_streaming failure, when
in fact they should be set to QUEUED. The videobuf2 core warns about this.
Reported-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Interrupt result flags have to be cleared before a hardware job is run.
Otherwise, if they are cleared asynchronously, we may end up clearing them
after the interrupt for which we wanted to wait has already arrived, thus
overwriting the job results that we intended to wait for.
To prevent this, clear the flags only under hw_lock and before running
a hardware job.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
G_CTRL on V4L2_CID_MIN_BUFFERS_FOR_CAPTURE will fail if userspace happens to
query it after getting a resolution change event and before the codec has
a chance to parse the header and switch to an initialized state.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This field is no longer used as MFC driver doesn't use vb2 alloc contexts
anymore.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While resolution change is detected by MFC, we flush out
older dpbs, send the resolution change event to application,
and then accept further queuing of new src buffers.
Sometimes, we error out during dpb flush because of lack of src
buffers. Since we have not started decoding new resolution yet,
it is simpler to push zero-size buffer until we flush out all dpbs.
This is already been done while handling EOS command, and this patch
extends the same logic to resolution change as well.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the software watchdog kicks in, we need to de-init MFC
before reloading firmware and re-intializing it again.
Signed-off-by: Arun Mankuzhi <arun.m@samsung.com>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MFC wakeup command has to be sent after the host receives
firmware load complete status from risc.
Signed-off-by: Arun Mankuzhi <arun.m@samsung.com>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the software watchdog kicks in, the watchdog worker is not synchronized
with hardware interrupts and does not block other instances. It's possible
for it to clear the hw_lock, making other instances trigger a BUG() on
hw_lock checks. Since it's not fatal to clear the hw_lock to zero twice,
just WARN in those cases for now. We should not explode, as firmware will
return errors as needed for other instances after it's reloaded, or they
will time out.
A clean fix should involve killing other instances when watchdog kicks in,
but requires a major redesign of locking in the driver.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
during reset sequence, it is advisable to follow the below
sequence, in order to avoid unexpected behavior from MFC
. set SFR 0x7110 MFC_BUS_RESET_CTRL 0x1
// wait for REQ_STATUS to be 1
. get SFR 0x7110 MFC_BUS_RESET_CTRL 0x3
// reset now
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reset sequence for MFC V7 and V8 do not need RISC_ON
to be set to 0, while for MFC V6 it is still needed.
Also, remove a couple of register settings during Reset
which are not needed from V6 onwards.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Timestamp i of a previously decoded buffer was overwritten for some
H.264 streams with timestamp i+1 of the next buffer. This happened when
encountering frame_type S5P_FIMV_DECODE_FRAME_SKIPPED, indicating no
new frame.
In most cases this wrong indexing might not have been noticed except
for a one frame delay in frame presentation. For H.264 streams though
that require reordering of frames for presentation, it caused a slightly
erratic presentation time lookup and consequently dropped frames in the
Pepper Flash plugin.
Signed-off-by: Ilja H. Friedel <ihf@google.com>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The enter_suspend flag is set after we enter mfc suspend function but if
suspend fails after that due to any reason (like hardware timeout etc),
this flag must be cleared before returning an error. Otherwise, this
flag never gets cleared and the MFC suspend will always return an error
on subsequent tries. If clock off fails, disable hw_lock also.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Handle REQBUFS(0) for CAPTURE queue as well. Also use the proper queue to call
it on for OUTPUT.
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add V4L2_CID_MIN_BUFFERS_FOR_OUTPUT query for encoder.
Once mfc encoder state is HEAD_PARSED, which is sequence
header produced, dpb_count is avaialable. Let user space
query this value.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds a quick check for valid JPEG frames before feeding them into
the bitstream buffer: Frames that do not begin with the JPEG start of image
marker and end with the end of image marker are dropped.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This should fix CODA crashes due to timeouts when stopping
the decoding process with SIGINT.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For small frame sizes, allocating 1 MiB per compressed buffer is a waste of
space. On the other hand, incompressible 1080p data can produce JPEGs larger
than 1 MiB at higher quality settings. Allow userspace to set the compressed
buffer size and clamp the value to a sensible range.
Also set the initial sizeimage to a value inside the range allowed by try_fmt.
While at it, reduce the default image size to a maximum of 1920*1088 (otherwise
JPEG will default to 8k*8k and 96 MiB buffers).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With bitstream padding, it is possible to decode a single JPEG in the bitstream
immediately. This allows us to only ever queue a single JPEG into the bitstream
buffer, except to increase payload over 512 bytes or to back out of hold state.
This is a measure to decrease JPEG decoder latency.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Before starting a PIC_RUN, pad the bitstream with 0xff until 256 bytes
past the next multiple of 256 bytes, if the buffer to be decoded is the
last buffer in the bitstream.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Storing the buffer position in the bitstream with the buffer metadata
allows to later use that information to drop metadata for skipped buffers
and to determine whether bitstream padding has to be applied.
This patch also renames struct coda_timestamp to struct coda_buffer_meta
to make clear that it contains more than only the buffer timestamp.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds JPEG encoding and decoding support for CODA7541,
using the BIT processor. Separate JPEG encoder and decoder video
devices are created due to different streaming behaviour and
different supported pixel formats.
The hardware can not change subsampling on the fly, but encode
and decode 4:2:2 subsampled JPEG images from and into this format.
The CODA7541 JPEG decoder uses the bitstream buffer and thus can run
without new buffers queued if there is a buffer in the bitstream.
Since there is no standard way to store the colorspace used in
JPEGs, and to make v4l2-compliance happy, the JPEG format always
reports V4L2_COLORSPACE_JPEG.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch splits the encoder specific controls out of the main control setup
function. This way each video device registers only relevant controls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Each video device descriptor determines the name, callback ops, and input and
output formats on the corresponding video device. This simplifies coda_enum_fmt
and coda_try_fmt a bit and will simplify adding separate video devices for JPEG
codecs due to the slightly different behavior in the CodaDx6/CODA7542 case and
a separate hardware unit on CODA960.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
