When waiting for a request claim the SBAL before waiting. This way,
locking before each check of the free counter is not required and
sparse does not emit warnings for the complicated locking scheme.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Synchronize the registration and de-registration with the SCSI layer
at CCW registration, de-registration. Before we registered with the
SCSI layer on adapter activation. This way the reg and de-reg process
is in balance.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Move the closing parenthesis before the line break.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
The loop above the modified code only terminates when rc is a valid pointer.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E;
position p1,p2;
@@
if (x@p1 == NULL || ...) { ... when forall
return ...; }
... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\)
(
x@p2 == NULL
|
x@p2 != NULL
)
// another path to the test that is not through p1?
@s exists@
local idexpression r.x;
position r.p1,r.p2;
@@
... when != x@p1
(
x@p2 == NULL
|
x@p2 != NULL
)
@fix depends on !s@
position r.p1,r.p2;
expression x,E;
statement S1,S2;
@@
(
- if ((x@p2 != NULL) || ...)
S1
|
- if ((x@p2 == NULL) && ...) S1
|
- BUG_ON(x@p2 == NULL);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If reply is ERR_PTR(...), then it should not be dereferenced, so I have
moved the dereference from the declaration to after the IS_ERR test.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@match exists@
expression x, E;
identifier fld;
position p1,p2;
@@
(
x = E;
|
x = E
|
x@p1->fld
... when != x = E
IS_ERR(x@p2)
... when any
)
@other_match exists@
expression match.x, E1, E2;
position match.p1,match.p2;
@@
x = E1
... when != x = E2
when != x@p1
x@p2
@ script:python depends on !other_match@
p1 << match.p1;
p2 << match.p2;
@@
print "* file %s dereference %s test %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
get rid of this one:
CC drivers/s390/char/sclp_vt220.o
drivers/s390/char/sclp_vt220.c:588: warning: '__sclp_vt220_flush_buffer' defined but not used
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To check if multipath is available we count the bits set in lpm,
which could change over time (via configure [on|off] of a path).
The following patch uses the pim (which is persistent) for this
decision.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Sometimes we change the pmcw configuration but don't call msch
to transmit these changes to the channel subsystem.
The patch fixes this by calling cio_commit_config in such cases.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To change the configuration of a subchannel we alter the modifiable
bits of the subchannel's schib field and issue a modify subchannel.
There can be the case that not all changes were applied -or worse-
quietly overwritten by the hardware. With the next store subchannel
we obtain the current state of the hardware but lose our target
configuration.
With this patch we introduce a subchannel_config structure which
contains the target subchannel configuration. Additionally the msch
wrapper cio_modify is replaced with cio_commit_config which
copies the desired changes to a temporary schib. msch is then
called with the temporary schib. This schib is only written back
to the subchannel if all changes were applied.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is the chance that we get condition code 0 for a stsch but
the resulting schib is not vaild. In the current code there are
2 cases:
* we do a check for validity of the schib after stsch, but at this
time we have already stored the invaild schib in the subchannel
structure. This may lead to problems.
* we don't do a check for validity, which is not that good either.
The patch addresses both issues by introducing the stsch wrapper
cio_update_schib which performs stsch on a local schib. This schib
is only written back to the subchannel if it's valid.
side note: For some functions (chp_events) the return codes are
different now (-ENXIO vs -ENODEV) but this shouldn't do harm
since the caller doesn't check for _specific_ errors.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Check if a ccw device is registered via device_is_registered()
and not via the old kludge of checking the membership in driver
core internal klists.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Just put the cdev's reference count to give up our reference.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we fail the probe for an I/O subchannel, we won't be able
to unregister it again since there are no sch_event()
callbacks for unbound subchannels. Just succeed the probe in
any case and schedule unregistering the subchannel.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is a race between io_subchannel_register() and
io_subchannel_sch_event() which may cause a subchannel to be
unregistered because it is no longer operational before
io_subchannel_register() had run. We need to check whether the
subchannel is still registered before the ccw device can be
registered and just bail out if it is not.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Subchannel refcounting was incorrect in some places, especially
a refcount was missing when ccw_device_call_sch_unregister()
was called and the refcount was not correctly switched after
moving devices.
Fix this by establishing the following rules:
- The ccw_device obtains a reference on its parent subchannel
when dev.parent is set and gives it up in its release
function. This is needed because we need a parent reference
for correct refcounting even before the ccw device is (if at
all) registered.
- When calling device_move(), obtain a reference on the new
subchannel before moving the ccw device and give up the
reference on the old parent after moving. This brings the
refcount in line with the first rule.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current code attempts to get an extra reference count
for online devices by doing a get_device() in ccw_device_online()
and a put_device() in ccw_device_done(). However, this
- incorrectly obtains an extra reference for disconnected
devices becoming available again (since they are already
online)
- needs special checks for css_init_done in order to handle
the console device
- is not obvious and
- may incorretly drop a reference count in ccw_device_done() if
that function is called after path verification for a device
that just became not operational.
So let's just get the reference in ccw_device_set_online() and
drop it in ccw_device_set_offline(). (Unfortunately, we still
need the special case in io_subchannel_probe().)
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure atomicity of ungroup operation to prevent concurrent ungroup
and online processing which may lead to use-after-release situations.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Due to former patches a comment and device id initialization were
split from the addressed function call in io_subchannel_probe.
Move it back to where it belongs.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move cio_tpi() to the rest of the CONFIG_CCW_CONSOLE functions to
get rid of this one:
drivers/s390/cio/cio.c:115: warning: 'cio_tpi' defined but not used
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
__dasd_cleanup_cqr should be called with request_queue_lock held and
__dasd_block_process_erp with queue_lock
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
SIM sense data are always 32 bit sense data so sense byte 27 bit 0
has not to be set.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For a large number of I/O requests the values were shifted binary.
The shift was not transparent for the user because the shift value
was not displayed. To make this interface more human readable the
values are shifted decimal and the scale factor is displayed.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Register zfcp with the new /proc/service_level interface to report the
FCP microcode level. When the adapter goes offline or a channel path
disappears, zfcp unregisters, since the microcode version might change
and zfcp does not know about it.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a new proc interface /proc/service_levels that allows any code
to report a relevant service level, e.g. the microcode level of
devices, the service level of the hypervisor, etc.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Hipersocket connections can encounter temporary busy conditions.
In case of the busy bit set we retry the SIGA operation immediatelly.
If the busy condition still persists after 100 ms we fail and report
the error to the upper layer. The second stage retry logic is removed.
In case of ongoing busy conditions the upper layer needs to reset the
connection.
The reporting of a SIGA error is now done synchronously to allow the
network driver to requeue the buffers. Also no error trace is created
for the temporary SIGA errors so the error message view is not flooded.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- Use automatic acknowledgement of incoming buffers in QEBSM mode
- Move ACK for non-QEBSM mode always to the newest buffer to prevent
a race with qdio_stop_polling
- Remove the polling spinlock, the upper layer drivers return new buffers
in the same code path and could not run in parallel
- Don't flood the error log in case of no-target-buffer-empty
- In handle_inbound we check if we would overwrite an ACK'ed buffer, if so
advance the pointer to the oldest ACK'ed buffer so we don't overwrite an
empty buffer in qdio_stop_polling
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- make qdio_trace a per device view
- remove s390dbf exceptions
- remove CONFIG_QDIO_DEBUG, not needed anymore if we check for the level
before calling sprintf
- use snprintf for dbf entries
- add start markers to see if the dbf view wrapped
- add a global error view for all queues
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The QEBSM instructions are only available for CONFIG_64BIT, they are not
used under 31 bit. Make compiler happy about the false positive:
drivers/s390/cio/qdio_main.c: In function ?qdio_inbound_q_done?:
drivers/s390/cio/qdio_main.c:532: warning: ?state? may be used uninitialized in this function
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add counters for the eqbs and sqbs instructions that indicate how often
we issued the instructions and how often the instructions returned with
less buffers than specified.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
qeth needs to get the port count information before
qdio has allocated a page for the chsc operation.
Extend qdio_get_ssqd_desc() to store the data in the
specified structure.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>