Using inverted FS polarity in OSK5912 must be an error since TLV320AIC23
do not have support for inverted polarities. This is mostly due the hassle
with the DSP formats in OMAP McBSP DAI and inversion on OMAP side probably
just made this configuration working at some point.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DSP format wasn't still correct in OMAP McBSP DAI even after the commit
bd25867a6c.
Thanks to Peter Ujfalusi <peter.ujfalusi@nokia.com> for noticing and being
part of the fix. Now the FS length definition is more clear by defining
it with FWID(0).
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix accidental change of <mach/regs-gpio.h> to
<plat/regs-gpio.h> in s3c2412-i2s.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the build error in s3c-i2s-v2.c caused by
a change to the snd_soc_dai ops field.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The definition of s3c_i2sv2_iis_calc_rate was never
renamed from s3c2412_iis_calc_rate, so rename this
to allow the build to work.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix build errors in sound/soc/s3c24xx/jive_wm8750.c
from changes to ASoC.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
pxa_ssp_set_dai_fmt() currently has an early exit if the desired format
equals the current configuration. This is correct behaviour unless this
function is called with a zero value parameter for the first time.
Zero is a valid value for this function, but the early exit is bogus in
this case.
Hence, set priv->dai_fmt to -1 in the beginning so we can configure the
port.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Due to the process and communications issues with the 2.6.30 S3C
platform merges none of the underlying arch/arm code for S3C64xx audio
support made it into mainline, rendering the drivers useless. Disable
them in Kconfig to avoid user confusion - users patching in the required
support can always reenable this too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (36 commits)
ALSA: hda - Add VREF powerdown sequence for another board
ALSA: oss - volume control for CSWITCH and CROUTE
ALSA: hda - add missing comma in ad1884_slave_vols
sound: usb-audio: allow period sizes less than 1 ms
sound: usb-audio: save data packet interval in audioformat structure
sound: usb-audio: remove check_hw_params_convention()
sound: usb-audio: show sample format width in proc file
ASoC: fsl_dma: Pass the proper device for dma mapping routines
ASoC: Fix null dereference in ak4535_remove()
ALSA: hda - enable SPDIF output for Intel DX58SO board
ALSA: snd-atmel-abdac: increase periods_min to 6 instead of 4
ALSA: snd-atmel-abdac: replace bus_id with dev_name()
ALSA: snd-atmel-ac97c: replace bus_id with dev_name()
ALSA: snd-atmel-ac97c: cleanup registers when removing driver
ALSA: snd-atmel-ac97c: do a proper reset of the external codec
ALSA: snd-atmel-ac97c: enable interrupts to catch events for error reporting
ALSA: snd-atmel-ac97c: set correct size for buffer hardware parameter
ALSA: snd-atmel-ac97c: do not overwrite OCA and ICA when assigning channels
ALSA: snd-atmel-ac97c: remove dead break statements after return in switch case
ALSA: snd-atmel-ac97c: cleanup register definitions
...
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix for compillation error introduced by the constrain patch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver should pass a device that specifies internal DMA ops, but
substream->pcm is just a logical device, and thus doesn't have arch-
specific dma callbacks, therefore following bug appears:
Freescale Synchronous Serial Interface (SSI) ASoC Driver
------------[ cut here ]------------
kernel BUG at arch/powerpc/include/asm/dma-mapping.h:237!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c02259c4] snd_malloc_dev_pages+0x58/0xac
LR [c0225c74] snd_dma_alloc_pages+0xf8/0x108
Call Trace:
[df02bde0] [df02be2c] 0xdf02be2c (unreliable)
[df02bdf0] [c0225c74] snd_dma_alloc_pages+0xf8/0x108
[df02be10] [c023a100] fsl_dma_new+0x68/0x124
[df02be20] [c02342ac] soc_new_pcm+0x1bc/0x234
[df02bea0] [c02343dc] snd_soc_new_pcms+0xb8/0x148
[df02bed0] [c023824c] cs4270_probe+0x34/0x124
[df02bef0] [c0232fe8] snd_soc_instantiate_card+0x1a4/0x2f4
[df02bf20] [c0233164] snd_soc_instantiate_cards+0x2c/0x68
[df02bf30] [c0234704] snd_soc_register_platform+0x60/0x80
[df02bf50] [c03d5664] fsl_soc_platform_init+0x18/0x28
...
This patch fixes the issue by using card's device instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ak4535_remove() from sound/soc/codecs/ak4535.c calls
i2c_unregister_device() with a possibly null pointer.
This bug was found by smatch (http://repo.or.cz/w/smatch.git/).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds the needed code to be able to use 96KHz playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without this the WM9705 driver fails badly when resuming.
Tested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that any AC97 devices that bind to the CODEC are below the
ASoC device in the device tree so the suspend and resume code can
figure out what order to handle them in.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
AC97 devices may have other drivers hanging off them directly so need to
have resumed when the resume function returns meaning that we can't defer
the resume - complete it immediately for them. Non-AC97 devices should
not have other drivers hanging directly off the ASoC devices.
We only really need the deferral for non-AC97 devices - it's there since
some I2C buses are very slow and non-AC97 codecs often have large numbers
of registers to restore and require delays to bring the codec up cleanly
leading to a substantial impact on overall resume time.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
McBSP2 in OMAP3 has 1 ksample (1k x 32 bit) internal FIFO. During
initial playback startup, this FIFO is keeping the DMA request active
until the FIFO is full.
So now if ALSA buffer size is smaller, DMA is looping around it while
filling up the HW FIFO, generating burst of interrupts as well and SW
doesn't have any change to fill enough data.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In case of duplex mode (capture and playback at the same time), the second
stream has to have the same parameters (rate, sample size) as the already
running stream.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
TWL4030 supports 96KHz sample playback, but only playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Optimize the display of SSI statistics in the Freescale MPC8610 sound driver
to display the status count only of the interrupts that were actually enabled.
Previously, it would display the counts of all SISR status bits, even those
that were not enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove the delay from the trigger function in the Freescale MPC8610 sound
driver when capture is started. This delay was used to ensure that the DMA
controller was active when ALSA call the .pointer function to request a
DMA transfer status. A better approach is for the .pointer function to detect
that DMA has not started, and return zero instead. This change eliminates
the need for the delay.
Also add some related code to check for a DMA programming error, and report
XRUN if it occurs.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
HTC Magician has a Philips UDA1380 codec connected via
SSP1 (playback) and I2S (capture).
There is a flip-flop between the SSP frame clock output
and the codec's word select input pin. To make the codec
see proper I2S input, the SSP has to send two frames per
sample.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now magician and similar boards can use network mode with only one
active slot to explicitly set 16 bit frame width, even for S16_LE
stereo sound.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Headset was declared previously as a Headphone widget connecting
HSMIC and HSOL/HSOR pins of TWL4030 codec in SDP430 machine driver.
The capture path becomes invalid as the Headphone widget is not a
valid input endpoint.
Instead of that, the Headset is declared as separate Microphone
and Headphone widgets. Current patch modifies audio map:
- Headset Mic: HSMIC with bias
- Headset Stereophone: HSOL, HSOR
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add functions "Headset" and "Mic" to the control "Jack Function" for
activating and de-activating codec input pin LINE1L which is connected to
the mic pin of 4-pole Nokia AV connecter.
Note there is no mic bias voltage management here since bias is coming from
Nokia ASIC and driver for it is not in mainline.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is an AVDD supply as well, normally one or more of the other
upplies would be tied to it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The active discharge does not bring sufficient benefit to justify the
lengthy times involved so don't do that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit 14fa43f53f ("ASoC: Only
register AC97 bus if it's not done already") added a condition for
calling of soc_ac97_dev_register() but not added for calling of
soc_ac97_dev_unregister(). This patch adds same condition for
soc_ac97_dev_unregister(). Without this fix, kernel crashes when
unloading an asoc driver.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC sound/soc/codecs/twl4030.o
sound/soc/codecs/twl4030.c:1400: warning: braces around scalar initializer
sound/soc/codecs/twl4030.c:1400: warning: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1401: error: field name not in record or union initializer
sound/soc/codecs/twl4030.c:1401: error: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1401: warning: initialization from incompatible pointer type
sound/soc/codecs/twl4030.c:1402: error: field name not in record or union initializer
sound/soc/codecs/twl4030.c:1402: error: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1402: warning: excess elements in scalar initializer
sound/soc/codecs/twl4030.c:1402: warning: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1403: error: field name not in record or union initializer
sound/soc/codecs/twl4030.c:1403: error: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1403: warning: excess elements in scalar initializer
sound/soc/codecs/twl4030.c:1403: warning: (near initialization for 'twl4030_dai.ops')
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Two issues are fixed here:
- I2S transmits the left frame with the clock low but I don't seem to
get LRCLK out without SFRMDLY being set so invert SFRMP and set a
delay.
- I2S has a clock cycle prior to the first data byte in each channel
so we need to delay the data by one cycle.
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This switches the pxa ssp port usage from network mode to PSP mode.
Removed some comments and checks for configured TDM channels.
A special case is added to support configuration where BCLK = 64fs. We
need to do some black magic in this case which doesn't look nice but
there is unfortunately no other option than that.
Diagnosed-by: Tim Ruetz <tim@caiaq.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move headset jack registration to the codec/machine specific
initialization. Having the jack registration in machine init
causes that the jack device gets initialized but not registered
since the sound card is registered before the jack. Moving jack
registration to device initialization will register the jack
device along with all other devices associated to the card when
the card is registed. As a consequence of jack device registered
properly, the jack is detected as an input device.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The drivers are basically duplicating the same code over and over.
As snd_soc_cnew is going to be made static some time after the next
merge window, we might as well convert them now.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Refactor the WM8580 device registration to probe via standard I2C device
registration, registering the DAIs once the device has probed via I2C.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
