At http://dev.laptop.org/ticket/11980 we have determined that the
Marvell CaFe SDHCI controller reports bad card presence during
resume. It reports that no card is present even when it is.
This is a regression -- resume worked back around 2.6.37.
Around 400ms after resuming, a "card inserted" interrupt is
generated, at which point it starts reporting presence.
Work around this hardware oddity by setting the
SDHCI_QUIRK_BROKEN_CARD_DETECTION flag.
Thanks to Chris Ball for helping with diagnosis.
Signed-off-by: Daniel Drake <dsd@laptop.org>
[stable@: please apply to 3.0+]
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
For most error conditions sdhci_add_host() will print a diagnostic
message indicating why it failed but there are a few cases where this
does not happen. Add error messages in these cases to aid diagnosis.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The s3c2410_gpio* calls are obsolete and have been scheduled for
removal since several kernel releases. Remove them and use common
gpiolib API.
This patch is a prerequisite for removal of the S3C24XX SoC specific
arch/arm/plat-samsung/include/gpio-fns.h header.
Tested on Micro2440-SDK.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently only the capability_0 register can be set if
SDHCI_QUIRK_MISSING_CAPS is defined. This is a problem when
the capability_1 register also needs changing. Use the quirk
SDHCI_QUIRK_MISSING_CAPS to allow both registers to be set.
Redefining caps[1] is useful when the board design does not
support 1.8v vccq so UHS modes are not available. The code that
calls sdhci_add_host can then detect this condition and adjust
the caps so the UHS mode will not be attempted on UHS cards.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If bootloader or platform initialization code does not enable the
power supply to mmc slot, we need to do it in mmc driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull x86 platform changes from Ingo Molnar:
"This tree mostly involves various APIC driver cleanups/robustization,
and vSMP motivated platform callback improvements/cleanups"
Fix up trivial conflict due to printk cleanup right next to return value
change.
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (29 commits)
Revert "x86/early_printk: Replace obsolete simple_strtoul() usage with kstrtoint()"
x86/apic/x2apic: Use multiple cluster members for the irq destination only with the explicit affinity
x86/apic/x2apic: Limit the vector reservation to the user specified mask
x86/apic: Optimize cpu traversal in __assign_irq_vector() using domain membership
x86/vsmp: Fix vector_allocation_domain's return value
irq/apic: Use config_enabled(CONFIG_SMP) checks to clean up irq_set_affinity() for UP
x86/vsmp: Fix linker error when CONFIG_PROC_FS is not set
x86/apic/es7000: Make apicid of a cluster (not CPU) from a cpumask
x86/apic/es7000+summit: Always make valid apicid from a cpumask
x86/apic/es7000+summit: Fix compile warning in cpu_mask_to_apicid()
x86/apic: Fix ugly casting and branching in cpu_mask_to_apicid_and()
x86/apic: Eliminate cpu_mask_to_apicid() operation
x86/x2apic/cluster: Vector_allocation_domain() should return a value
x86/apic/irq_remap: Silence a bogus pr_err()
x86/vsmp: Ignore IOAPIC IRQ affinity if possible
x86/apic: Make cpu_mask_to_apicid() operations check cpu_online_mask
x86/apic: Make cpu_mask_to_apicid() operations return error code
x86/apic: Avoid useless scanning thru a cpumask in assign_irq_vector()
x86/apic: Try to spread IRQ vectors to different priority levels
x86/apic: Factor out default vector_allocation_domain() operation
...
Pull debug-for-linus git tree from Ingo Molnar.
Fix up trivial conflict in arch/x86/kernel/cpu/perf_event_intel.c due to
a printk() having changed to a pr_info() differently in the two branches.
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Move call to print_modules() out of show_regs()
x86/mm: Mark free_initrd_mem() as __init
x86/microcode: Mark microcode_id[] as __initconst
x86/nmi: Clean up register_nmi_handler() usage
x86: Save cr2 in NMI in case NMIs take a page fault (for i386)
x86: Remove cmpxchg from i386 NMI nesting code
x86: Save cr2 in NMI in case NMIs take a page fault
x86/debug: Add KERN_<LEVEL> to bare printks, convert printks to pr_<level>
Pull x86/asm changes from Ingo Molnar:
"Assorted single-commit improvements, as usual"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/mtrr: Slightly simplify print_mtrr_state()
x86/mm/mtrr: Fix alignment determination in range_to_mtrr()
x86/copy_user_generic: Optimize copy_user_generic with CPU erms feature
x86/alternatives: Use atomic_xchg() instead atomic_dec_and_test() for stop_machine_text_poke()
Pull timer core changes from Ingo Molnar:
"Continued cleanups of the core time and NTP code, plus more nohz work
preparing for tick-less userspace execution."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Rework timekeeping functions to take timekeeper ptr as argument
time: Move xtime_nsec adjustment underflow handling timekeeping_adjust
time: Move arch_gettimeoffset() usage into timekeeping_get_ns()
time: Refactor accumulation of nsecs to secs
time: Condense timekeeper.xtime into xtime_sec
time: Explicitly use u32 instead of int for shift values
time: Whitespace cleanups per Ingo%27s requests
nohz: Move next idle expiry time record into idle logic area
nohz: Move ts->idle_calls incrementation into strict idle logic
nohz: Rename ts->idle_tick to ts->last_tick
nohz: Make nohz API agnostic against idle ticks cputime accounting
nohz: Separate idle sleeping time accounting from nohz logic
timers: Improve get_next_timer_interrupt()
timers: Add accounting of non deferrable timers
timers: Consolidate base->next_timer update
timers: Create detach_if_pending() and use it
Pull perf events changes from Ingo Molnar:
"- kernel side:
- Intel uncore PMU support for Nehalem and Sandy Bridge CPUs, we
support both the events available via the MSR and via the PCI
access space.
- various uprobes cleanups and restructurings
- PMU driver quirks by microcode version and required x86 microcode
loader cleanups/robustization
- various tracing robustness updates
- static keys: remove obsolete static_branch()
- tooling side:
- GTK browser improvements
- perf report browser: support screenshots to file
- more automated tests
- perf kvm improvements
- perf bench refinements
- build environment improvements
- pipe mode improvements
- libtraceevent updates, we have now hopefully merged most bits with
the out of tree forked code base
... and many other goodies."
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (138 commits)
tracing: Check for allocation failure in __tracing_open()
perf/x86: Fix intel_perfmon_event_mapformatting
jump label: Remove static_branch()
tracepoint: Use static_key_false(), since static_branch() is deprecated
perf/x86: Uncore filter support for SandyBridge-EP
perf/x86: Detect number of instances of uncore CBox
perf/x86: Fix event constraint for SandyBridge-EP C-Box
perf/x86: Use 0xff as pseudo code for fixed uncore event
perf/x86: Save a few bytes in 'struct x86_pmu'
perf/x86: Add a microcode revision check for SNB-PEBS
perf/x86: Improve debug output in check_hw_exists()
perf/x86/amd: Unify AMD's generic and family 15h pmus
perf/x86: Move Intel specific code to intel_pmu_init()
perf/x86: Rename Intel specific macros
perf/x86: Fix USER/KERNEL tagging of samples
perf tools: Split event symbols arrays to hw and sw parts
perf tools: Split out PE_VALUE_SYM parsing token to SW and HW tokens
perf tools: Add empty rule for new line in event syntax parsing
perf test: Use ARRAY_SIZE in parse events tests
tools lib traceevent: Cleanup realloc use
...
Pull RCU changes from Ingo Molnar:
"Quoting from Paul, the major features of this series are:
1. Preventing latency spikes of more than 200 microseconds for
kernels built with NR_CPUS=4096, which is reportedly becoming the
default for some distros. This is a first step, as it does not
help with systems that actually -have- 4096 CPUs (work on this case
is in progress, but is not yet ready for mainline).
This category also includes improving concurrency of rcu_barrier(),
placed here due to conflicts. Posted to LKML at:
https://lkml.org/lkml/2012/6/22/381
Note that patches 18-22 of that series have been defered to 3.7, as
they have not yet proven themselves to be mainline-ready (and yes,
these are the ones intended to get rid of RCU's latency spikes for
systems that actually have 4096 CPUs).
2. Updates to documentation and rcutorture fixes, the latter category
including improvements to rcu_barrier() testing. Posted to LKML at
http://lkml.indiana.edu/hypermail/linux/kernel/1206.1/04094.html.
3. Miscellaneous fixes posted to LKML at:
https://lkml.org/lkml/2012/6/22/500
with the exception of the last commit, which was posted here:
http://www.gossamer-threads.com/lists/linux/kernel/1561830
4. RCU_FAST_NO_HZ fixes and improvements. Posted to LKML at:
http://lkml.indiana.edu/hypermail/linux/kernel/1206.1/00006.htmlhttp://www.gossamer-threads.com/lists/linux/kernel/1561833
The first four patches of the first series went into 3.5 to fix a
regression.
5. Code-style fixes. These were posted to LKML at
http://lkml.indiana.edu/hypermail/linux/kernel/1205.2/01180.htmlhttp://lkml.indiana.edu/hypermail/linux/kernel/1205.2/01181.html"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (48 commits)
rcu: Fix broken strings in RCU's source code.
rcu: Fix code-style issues involving "else"
rcu: Introduce check for callback list/count mismatch
rcu: Make RCU_FAST_NO_HZ respect nohz= boot parameter
rcu: Fix qlen_lazy breakage
rcu: Round FAST_NO_HZ lazy timeout to nearest second
rcu: The rcu_needs_cpu() function is not a quiescent state
rcu: Dump only the current CPU's buffers for idle-entry/exit warnings
rcu: Add check for CPUs going offline with callbacks queued
rcu: Disable preemption in rcu_blocking_is_gp()
rcu: Prevent uninitialized string in RCU CPU stall info
rcu: Fix rcu_is_cpu_idle() #ifdef in TINY_RCU
rcu: Split RCU core processing out of __call_rcu()
rcu: Prevent __call_rcu() from invoking RCU core on offline CPUs
rcu: Make __call_rcu() handle invocation from idle
rcu: Remove function versions of __kfree_rcu and __is_kfree_rcu_offset
rcu: Consolidate tree/tiny __rcu_read_{,un}lock() implementations
rcu: Remove return value from rcu_assign_pointer()
key: Remove extraneous parentheses from rcu_assign_keypointer()
rcu: Remove return value from RCU_INIT_POINTER()
...
Pull core/iommu changes from Ingo Molnar.
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
iommu/dmar: Use pr_format() instead of PREFIX to tidy up pr_*() calls
iommu/dmar: Reserve mmio space used by the IOMMU, if the BIOS forgets to
iommu/dmar: Replace printks with appropriate pr_*()
This reverts commit fbd24153c4.
This commit is subtly buggy: kstrto*int() can return an error but
it's not checked in every path. simple_strtoul() on the other hand
could not fail, so this patch subtly intruduces new failure modes.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Link: http://lkml.kernel.org/r/1338424803.3569.5.camel@lorien2
Signed-off-by: Ingo Molnar <mingo@kernel.org>
From Kukjin Kim <kgene.kim@samsung.com>:
It is including new exynos_defconfig for DT configuration of exynos4
and exynos5 together. The old exynos4_defconfig will be used for non-DT
for a while and we will try to move on using exynos_defconfig for only DT.
* samsung/defconfig:
ARM: exynos_defconfig: enable more platforms in defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables the new EXYNOS5 platforms in the defconfig, and enables DT
support on EXYNOS4.
Other options enabled: USB host, EXT3/4, regulators and tps65090,
networking and a few of the common usb ethernet adapters as well as the
smsc911x controller used on some boards.
I enabled EFI_PARTITION, since it's used on some filesystem images I'm
using. I didn't see a need to keep Solaris and BSD partition format
still enabled.
Finally, framebuffer console, logo and fonts were enabled.
Note that enabling some of these options introduces build coverage
previously missing, thus introducing a few build errors and warnings
for which fixes have been sent out already.
Signed-off-by: Olof Johansson <olof@lixom.net>
[kgene.kim@samsung.com: restored exynos4_defconfig from original]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
From Kukjin Kim <kgene.kim@samsung.com>:
You may think that 'since this is including only samsung spi stuff,
so this should be sent to upstream via spi tree', yeah right. But in
this time, would be helpful to us if they could be sent via arm-soc,
samsung tree for avoiding useless conflicts. Because samsung-dt-spi
branch touches the same driver and it is already in arm-soc tree.
* 'next/devel-samsung-spi' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
spi/s3c64xx: Expand S3C64XX_SPI_{DE,}ACT macros at call sites
spi/s3c64xx: Convert to devm_request_and_ioremap()
spi/s3c64xx: Put the /CS GPIO into output mode
spi/s3c64xx: Fix handling of errors in gpio_request()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Kukjin Kim <kgene.kim@samsung.com>:
It is including several changes for samsung boards.
* 'next/board-samsung-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add leds status1 and status2 on Origen board
ARM: S3C64XX: Mark most Cragganmore initdata devinitdata
ARM: EXYNOS: Add missing .reserve field to SMDKC210
ARM: EXYNOS: Add DRM device to SMDK4X12 board
ARM: S3C64XX: Clean up after SPI driver platform data updates
ARM: SAMSUNG: no need to set the value for clk_xusbxti when it is 24Mhz
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SYSTEM_SUSPEND_DISK system state is never used, so drop it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge emailed kgdb dmesg fixups patches from Anton Vorontsov:
"The dmesg command appears to be broken after the printk rework. The
old logic in the kdb code makes no sense in terms of current
printk/logging storage format, and KDB simply hangs forever upon
entering 'dmesg' command.
The first patch revives the command by switching to kmsg_dumper
iterator. As a side-effect, the code is now much more simpler.
A few changes were needed in the printk.c: we needed unlocked variant
of the kmsg_dumper iterator, but these can surely wait for 3.6.
It's probably too late even for the first patch to go to 3.5, but I'll
try to convince otherwise. :-) Here we go:
- The current code is broken for sure, and has no hope to work at
all. It is a regression
- The new code works for me, and probably works for everyone else;
- If it compiles (and I urge everyone to compile-test it on your
setup), it hardly can make things worse."
* Merge emailed patches from Anton Vorontsov: (4 commits)
kdb: Switch to nolock variants of kmsg_dump functions
printk: Implement some unlocked kmsg_dump functions
printk: Remove kdb_syslog_data
kdb: Revive dmesg command
The locked variants are prone to deadlocks (suppose we got to the
debugger w/ the logbuf lock held), so let's switch to nolock variants.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If used from KDB, the locked variants are prone to deadlocks (suppose we
got to the debugger w/ the logbuf lock held).
So, we have to implement a few routines that grab no logbuf lock.
Yet we don't need these functions in modules, so we don't export them.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function is no longer needed, so remove it.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kgdb dmesg command is broken after the printk rework. The old logic
in kdb code makes no sense in terms of current printk/logging storage
format, and KDB simply hangs forever.
This patch revives the command by switching to kmsg_dumper iterator.
The code is now much more simpler and shorter.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From Al Viro:
BTW, speaking of struct file treatment related to sockets -
there's this piece of code in iscsi:
/*
* The SCTP stack needs struct socket->file.
*/
if ((np->np_network_transport == ISCSI_SCTP_TCP) ||
(np->np_network_transport == ISCSI_SCTP_UDP)) {
if (!new_sock->file) {
new_sock->file = kzalloc(
sizeof(struct file), GFP_KERNEL);
For one thing, as far as I can see it'not true - sctp does *not* depend on
socket->file being non-NULL; it does, in one place, check socket->file->f_flags
for O_NONBLOCK, but there it treats NULL socket->file as "flag not set".
Which is the case here anyway - the fake struct file created in
__iscsi_target_login_thread() (and in iscsi_target_setup_login_socket(), with
the same excuse) do *not* get that flag set.
Moreover, it's a bloody serious violation of a bunch of asserts in VFS;
all struct file instances should come from filp_cachep, via get_empty_filp()
(or alloc_file(), which is a wrapper for it). FWIW, I'm very tempted to
do this and be done with the entire mess:
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andy Grover <agrover@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The effect of the existing code is that we continue blindly when we
should warn about an invalid allocation unit.
Reported-by: dcb314@hotmail.com
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44061
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If we are using a regulator the SD Host Controller and the
regulator should agree about the voltages supported. Use
the common subset that is supported.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
max_current_caps can return 0 if not available from the sd controller.
If no regulator is present or the regulator specifies a current
less then 200ma, we no longer still set the 200mA caps bit anyway.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Aaron Lu <aaron_lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sd host controller spec indicates the the MAX_CURRENT value may
be returned as 0. In this case other methods need to be used to
return the current. If 0 is returned and there is a regulator,
ask the regulator for how much current is available.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Extend the sh_mmcif driver to support GPIO card detection, provided by the
slot function module. The original .get_cd() platform callback is also
preserved for now.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently mmc host drivers have to decide whether to enable card
detection before calling mmc_add_host() -- in which case a card
insertion event can arrive before the host has been completely
initialised -- or after mmc_add_host(), in which case the initial
card detection can be problematic.
This patch adds an explicit indication of when card detection should
not be carried out. With it in place enabling card detection before
calling mmc_add_host() should be safe. Similarly, disabling it again
after calling mmc_remove_host() will avoid any races.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add primitive OF support to the sh-mmcif driver, which also makes it
necessary to be able to run without platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add primitive support for OF to the SDHI TMIO glue, which also makes it
necessary to be able to run without platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The tmio-mmc driver is already using the generic GPIO CD handler in IRQ
mode. This patch adds support for CD polling mode and also checks for
availability of a WP GPIO.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Let SDHI platforms specify mmc_host::caps2 flags in their platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow tmio mmc glue drivers to pass mmc_host::caps2 flags down to
the mmc layer.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Card Write-Protect pin is often implemented, using a GPIO, which makes
it simple to provide a generic handler for it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This prepares for the addition of further slot functions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
A simple extension of mmc slot functions add support for CD GPIO polling
for cases where the GPIO cannot produce interrupts, or where this is not
desired for some reason.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
To handle CD and WP SD/MMC slot pins we need generic flags to specify their
polarity.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
struct mmc_host::hotplug is becoming a generic hook for slot functions.
Rename it accordingly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add regulator support to the sh_mmcif driver, but also preserve the current
power-callback.
Also note, that the card power is not switched off during clock gating
periods, hence there's no need to power it on every time the card is
re-activated.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
From the original version of sh_mmcif the .set_pwr() callback has only been
used to turn the card's power on, and the .down_pwr() callback has been
used to turn it off. .set_pwr() can be used for both these tasks, which is
also how it is implemented by the only user of this API: the SH7724 ecovec
board.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
With aggressive clock gating the clock can be disabled during interface
inactivity. During this time its frequency can be changed by another its
user. Therefore when the interface is activated again and the clock is
re-enabled, its frequency has to be re-read.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Regardless of whether the MMC bus clock is the same as the PM clock on
this specific interface, it has to be managed separately. Its proper
management should also include enabling and disabling of the clock,
whenever the interface is becoming active or going idle respectively.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
