Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Sathya Perla <sperla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most NICs that report NETIF_F_GSO_UDP_TUNNEL support VXLAN, and not
other UDP-based encapsulation protocols where the format and size of the
header differs. This patch implements a generic ndo_gso_check() for
VXLAN which will only advertise GSO support when the skb looks like it
contains VXLAN (or no UDP tunnelling at all).
Implementation shamelessly stolen from Tom Herbert:
http://thread.gmane.org/gmane.linux.network/332428/focus=333111
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-11-13
Please pull this set of a few more wireless fixes intended for the
3.18 stream...
For the mac80211 bits, Johannes says:
"This has just one fix, for an issue with the CCMP decryption
that can cause a kernel crash. I'm not sure it's remotely
exploitable, but it's an important fix nonetheless."
For the iwlwifi bits, Emmanuel says:
"Two fixes here - we weren't updating mac80211 if a scan
was cut short by RFKILL which confused cfg80211. As a
result, the latter wouldn't allow to run another scan.
Liad fixes a small bug in the firmware dump."
On top of that...
Arend van Spriel corrects a channel width conversion that caused a
WARNING in brcmfmac.
Hauke Mehrtens avoids a NULL pointer dereference in b43.
Larry Finger hits a trio of rtlwifi bugs left over from recent
backporting from the Realtek vendor driver.
Miaoqing Pan fixes a clocking problem in ath9k that could affect
packet timestamps and such.
Stanislaw Gruszka addresses an payload alignment issue that has been
plaguing rt2x00.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull libata fixes from Tejun Heo:
"The most notable is the revert of lock splitting optimization in ahci.
This also made the IRQ handling threaded even when there's only one
IRQ in use. The conversion missed IRFQ_SHARED leading to screaming
IRQs problem in some cases and the threaded IRQ handling showed
performance regression in some LKP test cases. The changes are
reverted for now. It'll probably be retried once threaded IRQ
handling is removed from ahci.
Other than that, there's one fix for ahci and several patches adding
device IDs"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: fix AHCI parameters not taken into account
ata: sata_rcar: Add r8a7793 device support
ahci: Add Device IDs for Intel Sunrise Point PCH
ahci: disable MSI instead of NCQ on Samsung pci-e SSDs on macbooks
Revert "AHCI: Optimize single IRQ interrupt processing"
Revert "AHCI: Do not acquire ata_host::lock from single IRQ handler"
ata: sata_rcar: Disable DIPM mode for r8a7790 ES1
There could be a signed overflow in the following code.
The expression, (32-logmask) is comprised between 0 and 31 included.
It may be equal to 31.
In such a case the left shift will produce a signed integer overflow.
According to the C99 Standard, this is an undefined behavior.
A simple fix is to replace the signed int 1 with the unsigned int 1U.
Signed-off-by: Vincent BENAYOUN <vincent.benayoun@trust-in-soft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block layer fixes from Jens Axboe:
"Four small fixes that should be merged for the current 3.18-rc series.
This pull request contains:
- a minor bugfix for computation of best IO priority given two
merging requests. From Jan Kara.
- the final (final) merge count issue that has been plaguing
virtio-blk. From Ming Lei.
- enable parallel reinit notify for blk-mq queues, to combine the
cost of an RCU grace period across lots of devices. From Tejun
Heo.
- an error handling fix for the SCSI_IOCTL_SEND_COMMAND ioctl. From
Tony Battersby"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: blk-merge: fix blk_recount_segments()
scsi: Fix more error handling in SCSI_IOCTL_SEND_COMMAND
blk-mq: make mq_queue_reinit_notify() freeze queues in parallel
block: Fix computation of merged request priority
- Fix a crash in the suspend-to-idle code path introduced by a
recent commit that forgot to check a pointer against NULL before
dereferencing it (Dmitry Eremin-Solenikov).
- Fix a boot crash on Exynos5 introduced by a recent commit making
that platform use generic Device Tree bindings for power domains
which exposed a weakness in the generic power domains framework
leading to that crash (Ulf Hansson).
- Fix a crash during system resume on systems where cpufreq depends
on Operation Performance Points (OPP) for functionality, but
CONFIG_OPP is not set. This leads the cpufreq driver registration
to fail, but the resume code attempts to restore the pre-suspend
cpufreq configuration (which does not exist) nevertheless and
crashes. From Geert Uytterhoeven.
- Add a new ACPI blacklist entry for Dell Vostro 3546 that has
problems if it is reported as Windows 8 compatible to the BIOS
(Adam Lee).
- Fix swapped arguments in an error message in the cpufreq-dt
driver (Abhilash Kesavan).
- Fix up the prototypes of new callbacks in struct generic_pm_domain
to make them more useful. Users of those callbacks will be added
in 3.19 and it's better for them to be based on the correct struct
definition in mainline from the start. From Ulf Hansson and
Kevin Hilman.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJUZhtnAAoJEILEb/54YlRxx1EP/0Rk7pJUHeOMmdyXyY7B+n+f
MlXHVMDhskT370fsdTGbpeYb5ATr5kGatfhr+vyDQmBtxdw7lDJxKq54s6kmmIL3
SEMRRb4NtkPsdDE7zq985JmjsrnHtKxC5NjSUwEGxdyyfAZxll4mrZL6RrqXCu44
L+qdVXRffCCrJDXZl5FZUpSZ3ZUc+xTiaDy7ObjLe2bwmzvBOAwS2flBMKxN9X+e
khlGdQZ0e9T2Y3IXriHxHMui8OVbkPyYZkW1aubCd0HwuTMP7sebosX/2JWdJOmg
q6bGcvPlBwXDRoShlzFO8CN5w5E8fIe0vfPcg9SB3s21S7rJEbYQX/5ytm107aJj
Ysv7mcb2dAHG0V3J7hxhkS+7UNPxfk3G+8frxW2UQ6eIDlZkBORIUhGCzeSbIGYM
aIKiomN4jGuPeaOkEnKl4RwMlzjuzAs2V06viffbq63eyWBvtHDW8M5bdq901pXp
1jOT7yKqLzOZYqcYaLr3z+IBw/+hfuG/FdCp3uGyFqeHPBNIP3BfFnWm6A6E13b+
aC6gvhQHojT7L2gqIBJ+Qn0EiRWNqwoLk6w6DLDYJna/hYyoXq0BKv+/x2OegItU
ENKYVpfmSt3YsEhcTBW4h5IpUvK07o5Oa3nTxen6924Im61dMyaSUDD5DiaqCgXO
bVJTsF983hBZGTy0IMX/
=wQxT
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are three regression fixes, two recent (generic power domains,
suspend-to-idle) and one older (cpufreq), an ACPI blacklist entry for
one more machine having problems with Windows 8 compatibility, a minor
cpufreq driver fix (cpufreq-dt) and a fixup for new callback
definitions (generic power domains).
Specifics:
- Fix a crash in the suspend-to-idle code path introduced by a recent
commit that forgot to check a pointer against NULL before
dereferencing it (Dmitry Eremin-Solenikov).
- Fix a boot crash on Exynos5 introduced by a recent commit making
that platform use generic Device Tree bindings for power domains
which exposed a weakness in the generic power domains framework
leading to that crash (Ulf Hansson).
- Fix a crash during system resume on systems where cpufreq depends
on Operation Performance Points (OPP) for functionality, but
CONFIG_OPP is not set. This leads the cpufreq driver registration
to fail, but the resume code attempts to restore the pre-suspend
cpufreq configuration (which does not exist) nevertheless and
crashes. From Geert Uytterhoeven.
- Add a new ACPI blacklist entry for Dell Vostro 3546 that has
problems if it is reported as Windows 8 compatible to the BIOS
(Adam Lee).
- Fix swapped arguments in an error message in the cpufreq-dt driver
(Abhilash Kesavan).
- Fix up the prototypes of new callbacks in struct generic_pm_domain
to make them more useful. Users of those callbacks will be added
in 3.19 and it's better for them to be based on the correct struct
definition in mainline from the start. From Ulf Hansson and Kevin
Hilman"
* tag 'pm+acpi-3.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Domains: Fix initial default state of the need_restore flag
PM / sleep: Fix entering suspend-to-IDLE if no freeze_oops is set
PM / Domains: Change prototype for the attach and detach callbacks
cpufreq: Avoid crash in resume on SMP without OPP
cpufreq: cpufreq-dt: Fix arguments in clock failure error message
ACPI / blacklist: blacklist Win8 OSI for Dell Vostro 3546
raw 1394 I/O took uninitialized kernel stack as substitute for missing ioctl()
argument data. This could partially show up in subsequent read() output.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mycw
-----END PGP SIGNATURE-----
Merge tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fix from Stefan Richter:
"IEEE 1394 (FireWire) subsystem fix: The character device file
interface for raw 1394 I/O took uninitialized kernel stack as
substitute for missing ioctl() argument data. This could partially
show up in subsequent read() output"
* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: cdev: prevent kernel stack leaking into ioctl arguments
Pull vfs fix from Al Viro:
"Fix for a really embarrassing braino in iov_iter. Kudos to paulus..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Fix thinko in iov_iter_single_seg_count
After removal of the central spinlock nf_conntrack_lock, in
commit 93bb0ceb75 ("netfilter: conntrack: remove central
spinlock nf_conntrack_lock"), it is possible to race against
get_next_corpse().
The race is against the get_next_corpse() cleanup on
the "unconfirmed" list (a per-cpu list with seperate locking),
which set the DYING bit.
Fix this race, in __nf_conntrack_confirm(), by removing the CT
from unconfirmed list before checking the DYING bit. In case
race occured, re-add the CT to the dying list.
While at this, fix coding style of the comment that has been
updated.
Fixes: 93bb0ceb75 ("netfilter: conntrack: remove central spinlock nf_conntrack_lock")
Reported-by: bill bonaparte <programme110@gmail.com>
Signed-off-by: bill bonaparte <programme110@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* pm-domains:
PM / Domains: Fix initial default state of the need_restore flag
PM / Domains: Change prototype for the attach and detach callbacks
* pm-sleep:
PM / sleep: Fix entering suspend-to-IDLE if no freeze_oops is set
* pm-cpufreq:
cpufreq: Avoid crash in resume on SMP without OPP
cpufreq: cpufreq-dt: Fix arguments in clock failure error message
Found by the UC-KLEE tool: A user could supply less input to
firewire-cdev ioctls than write- or write/read-type ioctl handlers
expect. The handlers used data from uninitialized kernel stack then.
This could partially leak back to the user if the kernel subsequently
generated fw_cdev_event_'s (to be read from the firewire-cdev fd)
which notably would contain the _u64 closure field which many of the
ioctl argument structures contain.
The fact that the handlers would act on random garbage input is a
lesser issue since all handlers must check their input anyway.
The fix simply always null-initializes the entire ioctl argument buffer
regardless of the actual length of expected user input. That is, a
runtime overhead of memset(..., 40) is added to each firewirew-cdev
ioctl() call. [Comment from Clemens Ladisch: This part of the stack is
most likely to be already in the cache.]
Remarks:
- There was never any leak from kernel stack to the ioctl output
buffer itself. IOW, it was not possible to read kernel stack by a
read-type or write/read-type ioctl alone; the leak could at most
happen in combination with read()ing subsequent event data.
- The actual expected minimum user input of each ioctl from
include/uapi/linux/firewire-cdev.h is, in bytes:
[0x00] = 32, [0x05] = 4, [0x0a] = 16, [0x0f] = 20, [0x14] = 16,
[0x01] = 36, [0x06] = 20, [0x0b] = 4, [0x10] = 20, [0x15] = 20,
[0x02] = 20, [0x07] = 4, [0x0c] = 0, [0x11] = 0, [0x16] = 8,
[0x03] = 4, [0x08] = 24, [0x0d] = 20, [0x12] = 36, [0x17] = 12,
[0x04] = 20, [0x09] = 24, [0x0e] = 4, [0x13] = 40, [0x18] = 4.
Reported-by: David Ramos <daramos@stanford.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
On a mx28evk with a sgtl5000 codec we notice a loud 'click' sound to happen
5 seconds after the end of a playback.
The SMALL_POP bit should fix this, but its definition is incorrect:
according to the sgtl5000 manual it is bit 0 of CHIP_REF_CTRL register, not
bit 1.
Fix the definition accordingly and enable the bit as intended per the code
comment.
After applying this change, no loud 'click' sound is heard after playback
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This fixes a crash in virtio console
multi-channel mode that got introduced in -rc1.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUZSAsAAoJECgfDbjSjVRpsqkIAJdGYmLWLHmU1FeuT336FbD6
4mj9+b9PX+gG6pjEyWcM/hEEx7MHp/0+evyeFXkeVwSdKxoV9/F/VRAMW/LnyNvS
rsJmv8ptvEscGwvwLHwnV4/xBcY8z676JxcnE4E/0KFLhRoP3h8/Bwel9wl0R8Sp
BDV0ddZLbPOzCgVgOGgXkEZ7xmhwHsSlRJO6wpkzB7c4Z8QJjx6cbdiM4XcTnaaM
nX5HsAG0y3Dm6CwNYrXukv4obxyOsVyt1kJGOiTjnzqhqUCFARRRM3CyDNV8+IbM
qUFArNxdMoUfyhCkDqyLdrOw0gwsWkXWErunkgzPKYY3lYUF8NxqFCKbAhTwrSY=
=tNTR
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio bugfix from Michael S Tsirkin:
"This fixes a crash in virtio console multi-channel mode that got
introduced in -rc1"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_console: move early VQ enablement
Pull networking fixes from David Miller:
1) sunhme driver lacks DMA mapping error checks, based upon a report by
Meelis Roos.
2) Fix memory leak in mvpp2 driver, from Sudip Mukherjee.
3) DMA memory allocation sizes are wrong in systemport ethernet driver,
fix from Florian Fainelli.
4) Fix use after free in mac80211 defragmentation code, from Johannes
Berg.
5) Some networking uapi headers missing from Kbuild file, from Stephen
Hemminger.
6) TUN driver gets csum_start offset wrong when VLAN accel is enabled,
and macvtap has a similar bug, from Herbert Xu.
7) Adjust several tunneling drivers to set dev->iflink after registry,
because registry sets that to -1 overwriting whatever we did. From
Steffen Klassert.
8) Geneve forgets to set inner tunneling type, causing GSO segmentation
to fail on some NICs. From Jesse Gross.
9) Fix several locking bugs in stmmac driver, from Fabrice Gasnier and
Giuseppe CAVALLARO.
10) Fix spurious timeouts with NewReno on low traffic connections, from
Marcelo Leitner.
11) Fix descriptor updates in enic driver, from Govindarajulu
Varadarajan.
12) PPP calls bpf_prog_create() with locks held, which isn't kosher.
Fix from Takashi Iwai.
13) Fix NULL deref in SCTP with malformed INIT packets, from Daniel
Borkmann.
14) psock_fanout selftest accesses past the end of the mmap ring, fix
from Shuah Khan.
15) Fix PTP timestamping for VLAN packets, from Richard Cochran.
16) netlink_unbind() calls in netlink pass wrong initial argument, from
Hiroaki SHIMODA.
17) vxlan socket reuse accidently reuses a socket when the address
family is different, so we have to explicitly check this, from
Marcelo Lietner.
18) Fix missing include in nft_reject_bridge.c breaking the build on ppc
and other architectures, from Guenter Roeck.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
vxlan: Do not reuse sockets for a different address family
smsc911x: power-up phydev before doing a software reset.
lib: rhashtable - Remove weird non-ASCII characters from comments
net/smsc911x: Fix delays in the PHY enable/disable routines
net/smsc911x: Fix rare soft reset timeout issue due to PHY power-down mode
netlink: Properly unbind in error conditions.
net: ptp: fix time stamp matching logic for VLAN packets.
cxgb4 : dcb open-lldp interop fixes
selftests/net: psock_fanout seg faults in sock_fanout_read_ring()
net: bcmgenet: apply MII configuration in bcmgenet_open()
net: bcmgenet: connect and disconnect from the PHY state machine
net: qualcomm: Fix dependency
ixgbe: phy: fix uninitialized status in ixgbe_setup_phy_link_tnx
net: phy: Correctly handle MII ioctl which changes autonegotiation.
ipv6: fix IPV6_PKTINFO with v4 mapped
net: sctp: fix memory leak in auth key management
net: sctp: fix NULL pointer dereference in af->from_addr_param on malformed packet
net: ppp: Don't call bpf_prog_create() in ppp_lock
net/mlx4_en: Advertize encapsulation offloads features only when VXLAN tunnel is set
cxgb4 : Fix bug in DCB app deletion
...
A chapter is added to describe the trackpoint packets.
A section is added to describe the behaviour of the knob crc_enabled in
sysfs.
The introduction of the documentation only mentioned v1/v2, but in the
last part it already contains explanation of v3 and v4. The introduction
is updated.
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The detection of crc_enabled is known to fail for Fujitsu H730. A DMI
blacklist is added for that, but it can be expected that other laptops will
pop up with this.
Here a sysfs knob is provided to alter the behaviour of crc_enabled.
Writing 0 or 1 to it sets the variable to 0 or 1. Reading it will show the
crc_enabled variable (0 or 1).
Reported-by: Stefan Valouch <stefan@valouch.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the past, no elantech was known with 3 touchpad mouse buttons.
Fujitsu H730 is the first known elantech with a middle button. This commit
enables this middle button. For backwards compatibility, the Fujitsu is
detected via DMI, and only for this one 3 buttons will be announced.
Reported-by: Stefan Valouch <stefan@valouch.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sometimes on Dell Latitude laptops psmouse/alps driver receive invalid ALPS
protocol V3 packets with bit7 set in last byte. More often it can be
reproduced on Dell Latitude E6440 or E7440 with closed lid and pushing
cover above touchpad.
If bit7 in last packet byte is set then it is not valid ALPS packet. I was
told that ALPS devices never send these packets. It is not know yet who
send those packets, it could be Dell EC, bug in BIOS and also bug in
touchpad firmware...
With this patch alps driver does not process those invalid packets, but
instead of reporting PSMOUSE_BAD_DATA, getting into out of sync state,
getting back in sync with the next byte and spam dmesg we return
PSMOUSE_FULL_PACKET. If driver is truly out of sync we'll fail the checks
on the next byte and report PSMOUSE_BAD_DATA then.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Merge misc fixes from Andrew Morton:
"15 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS: add IIO include files
kernel/panic.c: update comments for print_tainted
mem-hotplug: reset node present pages when hot-adding a new pgdat
mem-hotplug: reset node managed pages when hot-adding a new pgdat
mm/debug-pagealloc: correct freepage accounting and order resetting
fanotify: fix notification of groups with inode & mount marks
mm, compaction: prevent infinite loop in compact_zone
mm: alloc_contig_range: demote pages busy message from warn to info
mm/slab: fix unalignment problem on Malta with EVA due to slab merge
mm/page_alloc: restrict max order of merging on isolated pageblock
mm/page_alloc: move freepage counting logic to __free_one_page()
mm/page_alloc: add freepage on isolate pageblock to correct buddy list
mm/page_alloc: fix incorrect isolation behavior by rechecking migratetype
mm/compaction: skip the range until proper target pageblock is met
zram: avoid kunmap_atomic() of a NULL pointer
Pull Ceph fixes from Sage Weil:
"There is an overflow bug fix for cephfs from Zheng, a fix for handling
large authentication ticket buffers in libceph from Ilya, and a few
fixes for the request handling code from Ilya that affect RBD volumes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: change from BUG to WARN for __remove_osd() asserts
libceph: clear r_req_lru_item in __unregister_linger_request()
libceph: unlink from o_linger_requests when clearing r_osd
libceph: do not crash on large auth tickets
ceph: fix flush tid comparision
Pull HID fixes from Jiri Kosina:
- fix for an oops in HID core upon repeated subdriver insertion/removal
under certain circumstances, by Benjamin Tissoires
- quirk for another Elan Touchscreen device, by Adel Gadllah
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: cleanup .claimed field on disconnect
HID: usbhid: enable always-poll quirk for Elan Touchscreen 0103
Files under include/linux/iio were not reported as part of the IIO
subsystem.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reported-by: Cristina Ciocan <cristina.ciocan@intel.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 69361eef90 ("panic: add TAINT_SOFTLOCKUP") added the 'L' flag,
but failed to update the comments for print_tainted(). So, update the
comments.
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When memory is hot-added, all the memory is in offline state. So clear
all zones' present_pages because they will be updated in online_pages()
and offline_pages(). Otherwise, /proc/zoneinfo will corrupt:
When the memory of node2 is offline:
# cat /proc/zoneinfo
......
Node 2, zone Movable
......
spanned 8388608
present 8388608
managed 0
When we online memory on node2:
# cat /proc/zoneinfo
......
Node 2, zone Movable
......
spanned 8388608
present 16777216
managed 8388608
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [3.16+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In free_area_init_core(), zone->managed_pages is set to an approximate
value for lowmem, and will be adjusted when the bootmem allocator frees
pages into the buddy system.
But free_area_init_core() is also called by hotadd_new_pgdat() when
hot-adding memory. As a result, zone->managed_pages of the newly added
node's pgdat is set to an approximate value in the very beginning.
Even if the memory on that node has node been onlined,
/sys/device/system/node/nodeXXX/meminfo has wrong value:
hot-add node2 (memory not onlined)
cat /sys/device/system/node/node2/meminfo
Node 2 MemTotal: 33554432 kB
Node 2 MemFree: 0 kB
Node 2 MemUsed: 33554432 kB
Node 2 Active: 0 kB
This patch fixes this problem by reset node managed pages to 0 after
hot-adding a new node.
1. Move reset_managed_pages_done from reset_node_managed_pages() to
reset_all_zones_managed_pages()
2. Make reset_node_managed_pages() non-static
3. Call reset_node_managed_pages() in hotadd_new_pgdat() after pgdat
is initialized
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [3.16+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One thing I did in this patch is fixing freepage accounting. If we
clear guard page and link it onto isolate buddy list, we should not
increase freepage count. This patch adds conditional branch to skip
counting in this case. Without this patch, this overcounting happens
frequently if guard order is set and CMA is used.
Another thing fixed in this patch is the target to reset order. In
__free_one_page(), we check the buddy page whether it is a guard page or
not. And, if so, we should clear guard attribute on the buddy page and
reset order of it to 0. But, current code resets original page's order
rather than buddy one's. Maybe, this doesn't have any problem, because
whole merged page's order will be re-assigned soon. But, it is better
to correct code.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Gioh Kim <gioh.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fsnotify() needs to merge inode and mount marks lists when notifying
groups about events so that ignore masks from inode marks are reflected
in mount mark notifications and groups are notified in proper order
(according to priorities).
Currently the sorting of the lists done by fsnotify_add_inode_mark() /
fsnotify_add_vfsmount_mark() and fsnotify() differed which resulted
ignore masks not being used in some cases.
Fix the problem by always using the same comparison function when
sorting / merging the mark lists.
Thanks to Heinrich Schuchardt for improvements of my patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=87721
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several people have reported occasionally seeing processes stuck in
compact_zone(), even triggering soft lockups, in 3.18-rc2+.
Testing a revert of commit e14c720efd ("mm, compaction: remember
position within pageblock in free pages scanner") fixed the issue,
although the stuck processes do not appear to involve the free scanner.
Finally, by code inspection, the bug was found in isolate_migratepages()
which uses a slightly different condition to detect if the migration and
free scanners have met, than compact_finished(). That has not been a
problem until commit e14c720efd allowed the free scanner position
between individual invocations to be in the middle of a pageblock.
In a relatively rare case, the migration scanner position can end up at
the beginning of a pageblock, with the free scanner position in the
middle of the same pageblock. If it's the migration scanner's turn,
isolate_migratepages() exits immediately (without updating the
position), while compact_finished() decides to continue compaction,
resulting in a potentially infinite loop. The system can recover only
if another process creates enough high-order pages to make the watermark
checks in compact_finished() pass.
This patch fixes the immediate problem by bumping the migration
scanner's position to meet the free scanner in isolate_migratepages(),
when both are within the same pageblock. This causes compact_finished()
to terminate properly. A more robust check in compact_finished() is
planned as a cleanup for better future maintainability.
Fixes: e14c720efd ("mm, compaction: remember position within pageblock in free pages scanner)
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: P. Christeas <xrg@linux.gr>
Tested-by: P. Christeas <xrg@linux.gr>
Link: http://marc.info/?l=linux-mm&m=141508604232522&w=2
Reported-by: Norbert Preining <preining@logic.at>
Tested-by: Norbert Preining <preining@logic.at>
Link: https://lkml.org/lkml/2014/11/4/904
Reported-by: Pavel Machek <pavel@ucw.cz>
Link: https://lkml.org/lkml/2014/11/7/164
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Having test_pages_isolated failure message as a warning confuses users
into thinking that it is more serious than it really is. In reality, if
called via CMA, allocation will be retried so a single
test_pages_isolated failure does not prevent allocation from succeeding.
Demote the warning message to an info message and reformat it such that
the text "failed" does not appear and instead a less worrying "PFNS
busy" is used.
This message is trivially reproducible on a 10GB x86 machine on 3.16.y
kernels configured with CONFIG_DMA_CMA.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unlike SLUB, sometimes, object isn't started at the beginning of the
slab in SLAB. This causes the unalignment problem after slab merging is
supported by commit 12220dea07 ("mm/slab: support slab merge").
Following is the report from Markos that fail to boot on Malta with EVA.
Calibrating delay loop... 19.86 BogoMIPS (lpj=99328)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 4096 (order: 0, 16384 bytes)
Mountpoint-cache hash table entries: 4096 (order: 0, 16384 bytes)
Kernel bug detected[#1]:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0-05639-g12220dea07f1 #1631
task: 1f04f5d8 ti: 1f050000 task.ti: 1f050000
epc : 80141190 alloc_unbound_pwq+0x234/0x304
Not tainted
ra : 80141184 alloc_unbound_pwq+0x228/0x304
Process swapper/0 (pid: 1, threadinfo=1f050000, task=1f04f5d8, tls=00000000)
Call Trace:
alloc_unbound_pwq+0x234/0x304
apply_workqueue_attrs+0x11c/0x294
__alloc_workqueue_key+0x23c/0x470
init_workqueues+0x320/0x400
do_one_initcall+0xe8/0x23c
kernel_init_freeable+0x9c/0x224
kernel_init+0x10/0x100
ret_from_kernel_thread+0x14/0x1c
[ end trace cb88537fdc8fa200 ]
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
alloc_unbound_pwq() allocates slab object from pool_workqueue. This
kmem_cache requires 256 bytes alignment, but, current merging code
doesn't honor that, and merge it with kmalloc-256. kmalloc-256 requires
only cacheline size alignment so that above failure occurs. However, in
x86, kmalloc-256 is luckily aligned in 256 bytes, so the problem didn't
happen on it.
To fix this problem, this patch introduces alignment mismatch check in
find_mergeable(). This will fix the problem.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reported-by: Markos Chandras <Markos.Chandras@imgtec.com>
Tested-by: Markos Chandras <Markos.Chandras@imgtec.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current pageblock isolation logic could isolate each pageblock
individually. This causes freepage accounting problem if freepage with
pageblock order on isolate pageblock is merged with other freepage on
normal pageblock. We can prevent merging by restricting max order of
merging to pageblock order if freepage is on isolate pageblock.
A side-effect of this change is that there could be non-merged buddy
freepage even if finishing pageblock isolation, because undoing
pageblock isolation is just to move freepage from isolate buddy list to
normal buddy list rather than to consider merging. So, the patch also
makes undoing pageblock isolation consider freepage merge. When
un-isolation, freepage with more than pageblock order and it's buddy are
checked. If they are on normal pageblock, instead of just moving, we
isolate the freepage and free it in order to get merged.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Heesub Shin <heesub.shin@samsung.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Ritesh Harjani <ritesh.list@gmail.com>
Cc: Gioh Kim <gioh.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All the caller of __free_one_page() has similar freepage counting logic,
so we can move it to __free_one_page(). This reduce line of code and
help future maintenance.
This is also preparation step for "mm/page_alloc: restrict max order of
merging on isolated pageblock" which fix the freepage counting problem
on freepage with more than pageblock order.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Heesub Shin <heesub.shin@samsung.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Ritesh Harjani <ritesh.list@gmail.com>
Cc: Gioh Kim <gioh.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In free_pcppages_bulk(), we use cached migratetype of freepage to
determine type of buddy list where freepage will be added. This
information is stored when freepage is added to pcp list, so if
isolation of pageblock of this freepage begins after storing, this
cached information could be stale. In other words, it has original
migratetype rather than MIGRATE_ISOLATE.
There are two problems caused by this stale information.
One is that we can't keep these freepages from being allocated.
Although this pageblock is isolated, freepage will be added to normal
buddy list so that it could be allocated without any restriction. And
the other problem is incorrect freepage accounting. Freepages on
isolate pageblock should not be counted for number of freepage.
Following is the code snippet in free_pcppages_bulk().
/* MIGRATE_MOVABLE list may include MIGRATE_RESERVEs */
__free_one_page(page, page_to_pfn(page), zone, 0, mt);
trace_mm_page_pcpu_drain(page, 0, mt);
if (likely(!is_migrate_isolate_page(page))) {
__mod_zone_page_state(zone, NR_FREE_PAGES, 1);
if (is_migrate_cma(mt))
__mod_zone_page_state(zone, NR_FREE_CMA_PAGES, 1);
}
As you can see above snippet, current code already handle second
problem, incorrect freepage accounting, by re-fetching pageblock
migratetype through is_migrate_isolate_page(page).
But, because this re-fetched information isn't used for
__free_one_page(), first problem would not be solved. This patch try to
solve this situation to re-fetch pageblock migratetype before
__free_one_page() and to use it for __free_one_page().
In addition to move up position of this re-fetch, this patch use
optimization technique, re-fetching migratetype only if there is isolate
pageblock. Pageblock isolation is rare event, so we can avoid
re-fetching in common case with this optimization.
This patch also correct migratetype of the tracepoint output.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Heesub Shin <heesub.shin@samsung.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Ritesh Harjani <ritesh.list@gmail.com>
Cc: Gioh Kim <gioh.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before describing bugs itself, I first explain definition of freepage.
1. pages on buddy list are counted as freepage.
2. pages on isolate migratetype buddy list are *not* counted as freepage.
3. pages on cma buddy list are counted as CMA freepage, too.
Now, I describe problems and related patch.
Patch 1: There is race conditions on getting pageblock migratetype that
it results in misplacement of freepages on buddy list, incorrect
freepage count and un-availability of freepage.
Patch 2: Freepages on pcp list could have stale cached information to
determine migratetype of buddy list to go. This causes misplacement of
freepages on buddy list and incorrect freepage count.
Patch 4: Merging between freepages on different migratetype of
pageblocks will cause freepages accouting problem. This patch fixes it.
Without patchset [3], above problem doesn't happens on my CMA allocation
test, because CMA reserved pages aren't used at all. So there is no
chance for above race.
With patchset [3], I did simple CMA allocation test and get below
result:
- Virtual machine, 4 cpus, 1024 MB memory, 256 MB CMA reservation
- run kernel build (make -j16) on background
- 30 times CMA allocation(8MB * 30 = 240MB) attempts in 5 sec interval
- Result: more than 5000 freepage count are missed
With patchset [3] and this patchset, I found that no freepage count are
missed so that I conclude that problems are solved.
On my simple memory offlining test, these problems also occur on that
environment, too.
This patch (of 4):
There are two paths to reach core free function of buddy allocator,
__free_one_page(), one is free_one_page()->__free_one_page() and the
other is free_hot_cold_page()->free_pcppages_bulk()->__free_one_page().
Each paths has race condition causing serious problems. At first, this
patch is focused on first type of freepath. And then, following patch
will solve the problem in second type of freepath.
In the first type of freepath, we got migratetype of freeing page
without holding the zone lock, so it could be racy. There are two cases
of this race.
1. pages are added to isolate buddy list after restoring orignal
migratetype
CPU1 CPU2
get migratetype => return MIGRATE_ISOLATE
call free_one_page() with MIGRATE_ISOLATE
grab the zone lock
unisolate pageblock
release the zone lock
grab the zone lock
call __free_one_page() with MIGRATE_ISOLATE
freepage go into isolate buddy list,
although pageblock is already unisolated
This may cause two problems. One is that we can't use this page anymore
until next isolation attempt of this pageblock, because freepage is on
isolate buddy list. The other is that freepage accouting could be wrong
due to merging between different buddy list. Freepages on isolate buddy
list aren't counted as freepage, but ones on normal buddy list are
counted as freepage. If merge happens, buddy freepage on normal buddy
list is inevitably moved to isolate buddy list without any consideration
of freepage accouting so it could be incorrect.
2. pages are added to normal buddy list while pageblock is isolated.
It is similar with above case.
This also may cause two problems. One is that we can't keep these
freepages from being allocated. Although this pageblock is isolated,
freepage would be added to normal buddy list so that it could be
allocated without any restriction. And the other problem is same as
case 1, that it, incorrect freepage accouting.
This race condition would be prevented by checking migratetype again
with holding the zone lock. Because it is somewhat heavy operation and
it isn't needed in common case, we want to avoid rechecking as much as
possible. So this patch introduce new variable, nr_isolate_pageblock in
struct zone to check if there is isolated pageblock. With this, we can
avoid to re-check migratetype in common case and do it only if there is
isolated pageblock or migratetype is MIGRATE_ISOLATE. This solve above
mentioned problems.
Changes from v3:
Add one more check in free_one_page() that checks whether migratetype is
MIGRATE_ISOLATE or not. Without this, abovementioned case 1 could happens.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Heesub Shin <heesub.shin@samsung.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Ritesh Harjani <ritesh.list@gmail.com>
Cc: Gioh Kim <gioh.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 7d49d88683 ("mm, compaction: reduce zone checking frequency in
the migration scanner") has a side-effect that changes the iteration
range calculation. Before the change, block_end_pfn is calculated using
start_pfn, but now it blindly adds pageblock_nr_pages to the previous
value.
This causes the problem that isolation_start_pfn is larger than
block_end_pfn when we isolate the page with more than pageblock order.
In this case, isolation would fail due to an invalid range parameter.
To prevent this, this patch implements skipping the range until a proper
target pageblock is met. Without this patch, CMA with more than
pageblock order always fails but with this patch it will succeed.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zram could kunmap_atomic() a NULL pointer in a rare situation: a zram
page becomes a full-zeroed page after a partial write io. The current
code doesn't handle this case and performs kunmap_atomic() on a NULL
pointer, which panics the kernel.
This patch fixes this issue.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Weijie Yang <weijie.yang.kh@gmail.com>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kuser helpers page is not set up on non-MMU systems, so it does
not make sense to allow CONFIG_KUSER_HELPERS to be enabled when
CONFIG_MMU=n. Allowing it to be set on !MMU results in an oops in
set_tls (used in execve and the arm_syscall trap handler):
Unhandled exception: IPSR = 00000005 LR = fffffff1
CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.0-rc1-00041-ga30465a #216
task: 8b838000 ti: 8b82a000 task.ti: 8b82a000
PC is at flush_thread+0x32/0x40
LR is at flush_thread+0x21/0x40
pc : [<8f00157a>] lr : [<8f001569>] psr: 4100000b
sp : 8b82be20 ip : 00000000 fp : 8b83c000
r10: 00000001 r9 : 88018c84 r8 : 8bb85000
r7 : 8b838000 r6 : 00000000 r5 : 8bb77400 r4 : 8b82a000
r3 : ffff0ff0 r2 : 8b82a000 r1 : 00000000 r0 : 88020354
xPSR: 4100000b
CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.0-rc1-00041-ga30465a #216
[<8f002bc1>] (unwind_backtrace) from [<8f002033>] (show_stack+0xb/0xc)
[<8f002033>] (show_stack) from [<8f00265b>] (__invalid_entry+0x4b/0x4c)
As best I can tell this issue existed for the set_tls ARM syscall
before commit fbfb872f5f "ARM: 8148/1: flush TLS and thumbee
register state during exec" consolidated the TLS manipulation code
into the set_tls helper function, but now that we're using it to flush
register state during execve, !MMU users encounter the oops at the
first exec.
Prevent CONFIG_MMU=n configurations from enabling
CONFIG_KUSER_HELPERS.
Fixes: fbfb872f5f (ARM: 8148/1: flush TLS and thumbee register state during exec)
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Reported-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To speed up decompression, the decompressor sets up a flat, cacheable
mapping of memory. However, when there is insufficient space to hold
the page tables for this mapping, we don't bother to enable the caches
and subsequently skip all the cache maintenance hooks.
Skipping the cache maintenance before jumping to the relocated code
allows the processor to predict the branch and populate the I-cache
with stale data before the relocation loop has completed (since a
bootloader may have SCTLR.I set, which permits normal, cacheable
instruction fetches regardless of SCTLR.M).
This patch moves the cache maintenance check into the maintenance
routines themselves, allowing the v6/v7 versions to invalidate the
I-cache regardless of the MMU state.
Cc: <stable@vger.kernel.org>
Reported-by: Marc Carino <marc.ceeeee@gmail.com>
Tested-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Previously we applied _HPX type 2 record Link Control register settings
only to bridges with a subordinate bus. But it's better to apply them to
all devices with a link because if the subordinate bus has not been
allocated yet, we won't apply settings to the device.
Use pcie_cap_has_lnkctl() to determine whether the device has a Link
Control register instead of looking at dev->subordinate.
[bhelgaas: changelog]
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
41e5c0f81d ("of/pci: Add pci_get_new_domain_nr() and
of_get_pci_domain_nr()") added parsing of the "linux,pci-domain" property,
but didn't add the binding documentation.
Since this property will be supported by a number of host bridge drivers,
add it to the common PCI binding doc.
Fixes: 41e5c0f81d ("of/pci: Add pci_get_new_domain_nr() and of_get_pci_domain_nr()")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
This is a single patch that fixes the VBLANK machinery after:
7ffd7a6851 drm: Always reject drm_vblank_get() after drm_vblank_off()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=oKTG
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.18-rc5' of git://people.freedesktop.org/~tagr/linux into drm-fixes
drm/tegra: Fixes for v3.18-rc5
This is a single patch that fixes the VBLANK machinery after:
7ffd7a6851 drm: Always reject drm_vblank_get() after drm_vblank_off()
* tag 'drm/tegra/for-3.18-rc5' of git://people.freedesktop.org/~tagr/linux:
drm/tegra: dc: Add missing call to drm_vblank_on()
One modesetting, one gk20a fix.
* 'linux-3.18' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/nv50/disp: Fix modeset on G94
drm/gk20a/fb: fix setting of large page size bit
one regression fix.
* tag 'drm-intel-fixes-2014-11-13' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix obj->map_and_fenceable across tiling changes
Currently, we only match against local port number in order to reuse
socket. But if this new vxlan wants an IPv6 socket and a IPv4 one bound
to that port, vxlan will reuse an IPv4 socket as IPv6 and a panic will
follow. The following steps reproduce it:
# ip link add vxlan6 type vxlan id 42 group 229.10.10.10 \
srcport 5000 6000 dev eth0
# ip link add vxlan7 type vxlan id 43 group ff0e::110 \
srcport 5000 6000 dev eth0
# ip link set vxlan6 up
# ip link set vxlan7 up
<panic>
[ 4.187481] BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
...
[ 4.188076] Call Trace:
[ 4.188085] [<ffffffff81667c4a>] ? ipv6_sock_mc_join+0x3a/0x630
[ 4.188098] [<ffffffffa05a6ad6>] vxlan_igmp_join+0x66/0xd0 [vxlan]
[ 4.188113] [<ffffffff810a3430>] process_one_work+0x220/0x710
[ 4.188125] [<ffffffff810a33c4>] ? process_one_work+0x1b4/0x710
[ 4.188138] [<ffffffff810a3a3b>] worker_thread+0x11b/0x3a0
[ 4.188149] [<ffffffff810a3920>] ? process_one_work+0x710/0x710
So address family must also match in order to reuse a socket.
Reported-by: Jean-Tsung Hsiao <jhsiao@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit be9dad1f9f ("net: phy: suspend phydev when going
to HALTED"), the PHY device will be put in a low-power mode using
BMCR_PDOWN if the the interface is set down. The smsc911x driver does
a software_reset opening the device driver (ndo_open). In such case,
the PHY must be powered-up before access to any register and before
calling the software_reset function. Otherwise, as the PHY is powered
down the software reset fails and the interface can not be enabled
again.
This patch fixes this scenario that is easy to reproduce setting down
the network interface and setting up again.
$ ifconfig eth0 down
$ ifconfig eth0 up
ifconfig: SIOCSIFFLAGS: Input/output error
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My editor spewed garbage that looked like memory corruption on
my screen. It turns out that a number of occurences of "fi" got
turned into a ligature.
This patch replaces these ligatures with the ASCII letters "fi".
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased delay in the smsc911x_phy_disable_energy_detect (from 1ms to 2ms).
Dropped delays in the smsc911x_phy_enable_energy_detect (100ms and 1ms).
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
I saw problems with soft reset due to wrong udelay timings.
After I fixed udelay, I measured the time needed to bring integrated PHY
from power-down to operational mode (the time beetween clearing EDPWRDOWN
bit and soft reset complete event). I got 1ms (measured using ktime_get).
The value is equal to the current value (1ms) used in the
smsc911x_phy_disable_energy_detect. It is near the upper bound and in order
to avoid rare soft reset faults it is doubled (2ms).
I don't know official timing for bringing up integrated PHY as specs doesn't
clarify this (or may be I didn't found).
It looks safe to drop delays before and after setting EDPWRDOWN bit
(enable PHY power-down mode). I didn't saw any regressions with the patch.
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
It is possible that PHY could enter power-down mode (ENERGYON clear),
between ENERGYON bit check in smsc911x_phy_disable_energy_detect and SRST
bit set in smsc911x_soft_reset. This could happen, for example, if someone
disconnect ethernet cable between the checks. The PHY in a power-down mode
would prevent the MAC portion of chip to be software reseted.
Initially found by code review, confirmed later using test case.
This is low probability issue, and in order to reproduce it you have to
run the script:
while true; do
ifconfig eth0 down
ifconfig eth0 up || break
done
While the script is running you have to plug/unplug ethernet cable many
times (using gpio controlled ethernet switch, for example) until get:
[ 4516.477783] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.512207] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.524658] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.559082] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.571990] ADDRCONF(NETDEV_UP): eth0: link is not ready
ifconfig: SIOCSIFFLAGS: Input/output error
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
