Add EDAC support for ecc errors reporting on the synopsys ddr
controller. The ddr ecc controller corrects single bit errors and
detects double bit errors.
Selected important-ish notes from the changelog:
- I have not taken care of spliting synps_edac_geterror_info function as
it adds additional indentation levels and moreover the existing changes
were made as part of the v2 review comments
- Removed dt binding info as already there is a binding info available
under memorycontroller. so, updated ecc info there.
- Shortened the prefix "sysnopsys" to "synps"
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Link: http://lkml.kernel.org/r/a728a8d4678f4dbf9de189a480297c3d@BY2FFO11FD034.protection.gbl
[ Boris: massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
By popular demand, enable amd64_edac on 32-bit too.
Boris:
- update Kconfig text.
- add a warning on load which states that 32-bit configurations are unsupported.
Signed-off-by: Tomasz Pala <gotar@polanet.pl>
Link: http://lkml.kernel.org/r/20141102102212.GA7034@polanet.pl
Signed-off-by: Borislav Petkov <bp@suse.de>
This patch adds support for the CycloneV and ArriaV SDRAM controllers.
Correction and reporting of SBEs, Panic on DBEs.
There was a discussion thread on whether this driver should be an mfd driver
or just make use of syscon, which is already a mfd. Ultimately, the
decision to use a simple syscon interface was reached.[1]
[1] https://lkml.org/lkml/2014/7/30/514
[dinguyen] Fixed Kconfig to have EDAC_ALTERA_MC as a tristate to prevent a
build failure for allmodconfig.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Acked-by: Borislav Petkov <bp@suse.de>
[dinguyen] cleaned up commit message
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Pull EDAC updates from Mauro Carvalho Chehab.
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
sb_edac: add support for Haswell based systems
sb_edac: Fix mix tab/spaces alignments
edac: add DDR4 and RDDR4
sb_edac: remove bogus assumption on mc ordering
sb_edac: make minimal use of channel_mask
sb_edac: fix socket detection on Ivy Bridge controllers
sb_edac: update Kconfig description
sb_edac: search devices using product id
sb_edac: make RIR limit retrieval per model
sb_edac: make node id retrieval per model
sb_edac: make memory type detection per memory controller
Pull RAS updates from Ingo Molnar:
"The main changes in this cycle are:
- RAS tracing/events infrastructure, by Gong Chen.
- Various generalizations of the APEI code to make it available to
non-x86 architectures, by Tomasz Nowicki"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ras: Fix build warnings in <linux/aer.h>
acpi, apei, ghes: Factor out ioremap virtual memory for IRQ and NMI context.
acpi, apei, ghes: Make NMI error notification to be GHES architecture extension.
apei, mce: Factor out APEI architecture specific MCE calls.
RAS, extlog: Adjust init flow
trace, eMCA: Add a knob to adjust where to save event log
trace, RAS: Add eMCA trace event interface
RAS, debugfs: Add debugfs interface for RAS subsystem
CPER: Adjust code flow of some functions
x86, MCE: Robustify mcheck_init_device
trace, AER: Move trace into unified interface
trace, RAS: Add basic RAS trace event
x86, MCE: Kill CPU_POST_DEAD
Haswell memory controllers are very similar to Ivy Bridge and Sandy Bridge
ones. This patch adds support to Haswell based systems.
[m.chehab@samsung.com: Fix CodingStyle issues]
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
To avoid confuision and conflict of usage for RAS related trace event,
add an unified RAS trace event stub.
Start a RAS subsystem menu which will be fleshed out in time, when more
features get added to it.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Link: http://lkml.kernel.org/r/1402475691-30045-2-git-send-email-gong.chen@linux.intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Ever since commit 45f035ab9b ("CONFIG_HOTPLUG should be always on"),
it has been basically impossible to build a kernel with CONFIG_HOTPLUG
turned off. Remove all the remaining references to it.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull EDAC fixes and ghes-edac from Mauro Carvalho Chehab:
"For:
- Some fixes at edac drivers (i7core_edac, sb_edac, i3200_edac);
- error injection support for i5100, when EDAC debug is enabled;
- fix edac when it is loaded builtin (early init for the subsystem);
- a "Firmware First" EDAC driver, allowing ghes to report errors via
EDAC (ghes-edac).
With regards to ghes-edac, this fixes a longstanding BZ at Red Hat
that happens with Nehalem and Sandy Bridge CPUs: when both GHES and
i7core_edac or sb_edac are running, the error reports are
unpredictable, as both BIOS and OS race to access the registers. With
ghes-edac, the EDAC core will refuse to register any other concurrent
memory error driver.
This patchset moves the ghes struct definitions to a separate header
file (include/acpi/ghes.h) and adds 3 hooks at apei/ghes.c to
register/unregister and to report errors via ghes-edac. Those changes
were acked by ghes driver maintainer (Huang)."
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (30 commits)
i5100_edac: convert to use simple_open()
ghes_edac: fix to use list_for_each_entry_safe() when delete list items
ghes_edac: Fix RAS tracing
ghes_edac: Make it compliant with UEFI spec 2.3.1
ghes_edac: Improve driver's printk messages
ghes_edac: Don't credit the same memory dimm twice
ghes_edac: do a better job of filling EDAC DIMM info
ghes_edac: add support for reporting errors via EDAC
ghes_edac: Register at EDAC core the BIOS report
ghes: add the needed hooks for EDAC error report
ghes: move structures/enum to a header file
edac: add support for error type "Info"
edac: add support for raw error reports
edac: reduce stack pressure by using a pre-allocated buffer
edac: lock module owner to avoid error report conflicts
edac: remove proc_name from mci structure
edac: add a new memory layer type
edac: initialize the core earlier
edac: better report error conditions in debug mode
i5100_edac: Remove two checkpatch warnings
...
Register GHES at EDAC MC core, in order to avoid other
drivers to also handle errors and mangle with error data.
The edac core will warrant that just one driver will be used,
so the first one to register (BIOS first) will be the one that
will be reporting the hardware errors.
For now, the EDAC driver does nothing but to register at the
EDAC core, preventing the hardware-driven mechanism to
interfere with GHES.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After f65aad41772f("MIPS: Cavium: Add EDAC support."), when entering
the "Device Drivers" toplevel menu in menuconfig, the suboptions behind
EDAC appeared merged with the rest of the device drivers types. This was
because the menuconfig option EDAC is querying an EDAC_SUPPORT Kconfig
bool which was defined after the menu definition.
When pushing EDAC_SUPPORT up, before the menu definition, the variable
is defined earlier and the above menuconfig artifact doesn't happen.
Drop a useless menuconfig comment while at it.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Borislav Petkov <bp@alien8.de>
Pull MIPS updates from Ralf Baechle:
"The MIPS bits for 3.8. This also includes a bunch fixes that were
sitting in the linux-mips.org git tree for a long time. This pull
request contains updates to several OCTEON drivers and the board
support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
updates to the SSB bus support, MIPS kexec code and adds support for
kdump.
When pulling this, there are two expected merge conflicts in
include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
resolve, just remove the conflict markers and keep both alternatives."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
MIPS: PMC-Sierra Yosemite: Remove support.
VIDEO: Newport Fix console crashes
MIPS: wrppmc: Fix build of PCI code.
MIPS: IP22/IP28: Fix build of EISA code.
MIPS: RB532: Fix build of prom code.
MIPS: PowerTV: Fix build.
MIPS: IP27: Correct fucked grammar in ops-bridge.c
MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
MIPS: Fix potencial corruption
MIPS: Fix for warning from FPU emulation code
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
MIPS: Remove unused smvp.h
MIPS/EDAC: Improve OCTEON EDAC support.
MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
MIPS: Remove usage of CEVT_R4K_LIB config option.
...
Drivers for EDAC on Cavium. Supported subsystems are:
o CPU primary caches. These are parity protected only, so only error
reporting.
o Second level cache - ECC protected, provides SECDED.
o Memory: ECC / SECDEC if used with suitable DRAM modules. The driver will
will only initialize if ECC is enabled on a system so is safe to run on
non-ECC memory.
o PCI: Parity error reporting
Since it is very hard to test this sort of code the implementation is very
conservative and uses polling where possible for now.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Borislav Petkov <borislav.petkov@amd.com>
Only levels [0:4] are allowed so enforce that. Also, while at it,
massage Kconfig text and add valid debug levels range to the module
parameter description.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add support for L2 ECC on Calxeda highbank platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for memory controller on Calxeda Highbank platforms. Highbank
platforms support a single 4GB mini-DIMM with 1-bit correction and 2-bit
detection.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The old EDAC API is broken. It only works fine for systems manufatured
before 2005 and for AMD 64. The reason is that it forces all memory
controller drivers to discover rank info.
Also, it doesn't allow grouping the several ranks into a DIMM.
So, what almost all modern drivers do is to create a fake virtual-rank
information, and use it to cheat the EDAC core to accept the driver.
While this works if the user has enough time to discover what DIMM slot
corresponds to each "virtual-rank" information, it prevents EDAC usage
for users with less available time. It also makes life hard for vendors
that may want to provide a table with their motherboards to the userspace
tool (edac-utils) as each driver has its own logic for the virtual
mapping.
So, the old API should be removed, in favor of a more flexible API that
allows newer drivers to not lie to the EDAC core.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver needs to access PCIe Extended Configuration Space
Registers (0x100~0xfff), to correctly access those registers, we need
to enable PCI_MMCONFIG option. Since this option is not enabled for
X86_64 by default, we let the driver depend on it to prevent users
forgetting to enable this option.
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sb_edac driver is marginally useful on a 32-bit kernel, and
currently has 64-bit divide compile errors when building that config.
For now, make this build on only for 64-bit kernels.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some changes on it were required due to changeset cd90cc84c6bf0, that
changed the glue with the MCE logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both AMD and Intel i7 EDAC drivers use MCE features and are thus
dependent of this functionality present in the kernel. Express this in
Kconfig so that randconfig builds don't break.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove edac_mce pieces and use the normal MCE decoder notifier chain by
retaining the same functionality with considerably less code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit af9d220bac.
It turns out that one was meant to be applied on top of the edac.git
tree in -next that has more i7core_edac changes, but that wasn't clear
in the original email.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both AMD and Intel i7 EDAC drivers use MCE features and are thus
dependent of this functionality present in the kernel. Express this in
Kconfig so that randconfig builds don't break.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add tile support for the EDAC driver, which provides unified system
error (memory, PCI, etc.) reporting. For now, the TILEPro port
reports memory correctable error (CE) only.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
* 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/edac: (25 commits)
i7300_edac: Properly initialize per-csrow memory size
V4L/DVB: i7300_edac: better initialize page counts
MAINTAINERS: Add maintainer for i7300-edac driver
i7300-edac: CodingStyle cleanup
i7300_edac: Improve comments
i7300_edac: Cleanup: reorganize the file contents
i7300_edac: Properly detect channel on CE errors
i7300_edac: enrich FBD error info for corrected errors
i7300_edac: enrich FBD error info for fatal errors
i7300_edac: pre-allocate a buffer used to prepare err messages
i7300_edac: Fix MTR x4/x8 detection logic
i7300_edac: Make the debug messages coherent with the others
i7300_edac: Cleanup: remove get_error_info logic
i7300_edac: Add a code to cleanup error registers
i7300_edac: Add support for reporting FBD errors
i7300_edac: Properly detect the type of error correction
i7300_edac: Detect if the device is on single mode
i7300_edac: Adds detection for enhanced scrub mode on x8
i7300_edac: Clear the error bit after reading
i7300_edac: Add error detection code for global errors
...
Add sysfs injection facilities for testing of the MCE decoding code.
Remove large parts of amd64_edac_dbg.c, as a result, which did only
NB MCE injection anyway and the new injection code supports that
functionality already.
Add an injection module so that MCE decoding code in production kernels
like those in RHEL and SLES can be tested.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The file names are somehow misleading as the code is not specific to
AMD K8 CPUs anymore. The files accomodate code for other AMD CPU
northbridges as well.
Same is true for the config option which is valid for AMD CPU
northbridges in general and not specific to K8.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100917160343.GD4958@loge.amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This option differs from EDAC_DEBUG only by printing the file and
line of where the debug statement is placed, which contains unneeded
information. So remove it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Since commit 5753c082f6 ("powerpc/85xx:
Kconfig cleanup"), there is no MPC85xx Kconfig symbol anymore, so the
driver became non-selectable.
This patch fixes the issue by switching to PPC_85xx symbol.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Dave Jiang <djiang@mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
edac_mce module is an interface module that gets mcelog data and
forwards to any registered edac module that expects to receive data via
mce.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is meant to support i7 core/i7core extreme desktop
processors and Xeon 35xx/55xx series with integrated memory controller.
It is likely that it can be expanded in the future to work with other
processor series based at the same Memory Controller design.
For now, it has just a few MCH status reads.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This converts the MCE decoding logic into a standalone config
option which can be built-in or a module, the first one being the
default for MCEs happening early on in the boot process.
This, beyond being separated in a cleaner way, also saves RAM by
making the decoding logic modular.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <20091002133148.GD28682@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A driver for the Intel 3200 and 3210 memory controllers. It has only had
light testing so far, and currently makes no attempt to decode error
addresses at anything finer than csrow granularity.
Signed-off-by: Jason Uhlenkott <juhlenko@akamai.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Freescale MPC83xx memory controller to the existing
driver for the Freescale MPC85xx memory controller. The only difference
between the two processors are in the CS_BNDS register parsing code, which
has been changed so it will work on both processors.
The L2 cache controller does not exist on the MPC83xx, but the OF
subsystem will not use the driver if the device is not present in the OF
device tree.
I had to change the nr_pages calculation to make the math work out. I
checked it on my board and did the math by hand for a 64GB 85xx using 64K
pages. In both cases, nr_pages * PAGE_SIZE comes out to the correct
value.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-tip testing found the following build failure (config attached):
drivers/built-in.o: In function `amd64_check':
amd64_edac.c:(.text+0x3e9491): undefined reference to `amd_decode_nb_mce'
drivers/built-in.o: In function `amd64_init_2nd_stage':
amd64_edac.c:(.text+0x3e9b46): undefined reference to `amd_report_gart_errors'
amd64_edac.c:(.text+0x3e9b55): undefined reference to `amd_register_ecc_decoder'
drivers/built-in.o: In function `amd64_nbea_store':
amd64_edac_dbg.c:(.text+0x3ea22e): undefined reference to `amd_decode_nb_mce'
drivers/built-in.o: In function `amd64_remove_one_instance':
amd64_edac.c:(.devexit.text+0x3eea): undefined reference to `amd_report_gart_errors'
amd64_edac.c:(.devexit.text+0x3ef6): undefined reference to `amd_unregister_ecc_decoder'
the AMD EDAC code has a dependency on CONFIG_CPU_SUP_AMD facilities. The
patch below solves the problem here.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
