Updated version of 4446/1. This also drops the suggested comparison
of host_remain for == 0, since that doesn't make sense (still works
for us, too). We have verified that this patch solve race problems
on atleast 2 archs at high frequencies.
(Verbatim copy of old patch text below.)
The patch below fixes a race condition in the ARM MMCI PL18x driver.
If new data arrives in the FIFO while existing data is being read then
we get a second iteration of the loop in mmci_pio_read.
However host->size is not updated until after mmci_pio_read returns,
so we get count = number of new bytes PLUS number of bytes already
copied in the first iteration. This results in a FIFO underrun as
we try and read mode data than is available.
The fix is to compensating for data read on previous iterations
when calculating the amount of data in the FIFO.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Every file should include the headers containing the externs for its
global functions.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds proper prototypes for mmc_attach_*() in
drivers/mmc/core/core.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch makes the needlessly global __mmc_release_bus() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The quirk was meant to just inhibit some resets, but ended up blocking
all of them. Fortunately, this was just what was needed. Change the
comment to reflect reality.
Also, this issue has just been observed on Samsung laptops, so reduce
the number of chips the quirk affects.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The limit was a fixed 100k limit in the busy loop, which is not
accurate. It would better to have time limit for the worst case
which occurs when sending 80 cycles at 400 kHz and takes about
200 microseconds, so limit the max time spend in the busy loop
for some 250 microseconds.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Use work queues for starting new commands instead of starting them
directly from irq handler. The command scheduling needs to be delayed
a bit for some cards which should not be done from an interrupt.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
MMCA spec says the mmc clock should be kept running for at least
8 cycles after the last RW request. Ensure this with lazy clock
disable after a request, or with an explicit delay before
switching a slot.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Abort failed command from workqueue rather than from an interrupt,
allowing longer delays in abortion.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The cover waitqueue is occasionally scheduled twice from timer
and the interrupt and oops follows. It would have been possible
to fix this problem with spinlocks but using tasklet was a dropin
solution with no need for locking.
This path also adds some cleanups.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
If the get_cover_state is not set, it occurs the oops.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Using setup_timer() instead of init_timer() on omap.c file.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
When a card is removed while it is being accessed, a command can get stuck so
that no timeout or end of command interrupt ever occurs. The command getting
stuck is almost always CDM12, but also the other commands can get stuck. Catch
a stuck command with a timer and try sending the initialization stream until
the controller starts running again and responds with the end of command
status.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
General code cleanup, modifications at some dev_* functions and
other hacks at mmc_omap_irq() for MMC multislot support.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Modifications at power functions to MMC multislot support. This patch
also move board-specific code out of MMC OMAP driver.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix the data timeout calculation for MMC multislot support.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
New functions to support MMC multislot:
mmc_omap_release_dma() and mmc_omap_abort_xfer().
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds back MMC cover switch support in a way that
supports multiple slots.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Introduce new MMC multislot structure and change driver to use it.
Note that MMC clocking is now enabled in mmc_omap_select_slot()
and disabled in mmc_omap_release_slot().
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch removes the MMC cover switch handling temporarily
to make following multislot patches cleaner.
MMC cover switch handling will be added back in later patches
after adding basic multislot support.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
According with commit 255d01af9a
from Linux-OMAP tree, the BYTEBLOCK capability was removed by Pierre Ossman.
MMC_CAP_BYTEBLOCK is not defined causing the compile error:
drivers/mmc/host/omap.c: In function `mmc_omap_probe':
drivers/mmc/host/omap.c:1077: error: `MMC_CAP_BYTEBLOCK' undeclared (first use in this function)
drivers/mmc/host/omap.c:1077: error: (Each undeclared identifier is reported only once
drivers/mmc/host/omap.c:1077: error: for each function it appears in.)
Signed-off-by: Francisco Alecrim <francisco.alecrim@indt.org.br>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As noted by Kyungmin Park, the divisor calculation has
an unnecessary increase.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch removes some opcodes from host driver so there's no need on putting
'#include <linux/mmc/mmc.h>', that should not be needed in host drivers.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Hook up the controller LED to the LED subsystem, allowing more flexible
control than simply indicating an ongoing request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Reorganise code so that mmc_hostname() works directly after allocation.
That way host drivers can use that name for resource allocations and
messages during probing.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable MMC host
platform drivers, to re-enable auto loading.
Also, add missing owner declarations in driver init.
[dbrownell@users.sourceforge.net: registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suppressing uevents turned out to be a bad idea as it screws up the
order of events, making user space very confused. Change the system to
use sysfs groups instead.
This is a regression that, for some odd reason, has gone unnoticed for
some time. It confuses hal so that the block devices (which have the
mmc device as a parent) are not registered. End result being that
desktop magic when cards are inserted won't work.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the Ricoh RL5c476 chip: with this
the mmc adapter that needs this disabler (R5C843) can also be
handled correctly when it sits on a RL5c476.
Signed-off-by: Frank Seidel <fseidel@suse.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Update the AT91 MMC driver to use the generic GPIO calls instead of the
AT91-specific calls; and to request (and release) those GPIO signals.
That required updating the probe() fault cleanup codepaths. Now there
is a single sequence for freeing resources, in reverse order of their
allocation. Also that code uses use dev_*() for messaging, and has less
abuse of KERN_ERR.
Likewise with updating remove() cleanup. This had to free the GPIOs,
and while adding that code I noticed and fixed two other problems: it
was poking at a workqueue owned by the mmc core; and in one (rare)
case would try freeing an IRQ that it didn't allocate.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some devices have several controllers; need add the index info to
device slot name host->slot_desc[]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Both of these drivers work well (although some hardware still has
its problems) and are not in the "alpha" quality that EXPERIMENTAL
suggests.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As pci config space is reinitialised on a suspend/resume cycle, the
disabler needs to work its magic at resume time. For symmetry this
change also explicitly enables the controller at suspend time but
it's not strictly necessary.
Signed-off-by: Philipl Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch converts mmc to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move the tps65010 header file from the OMAP arch directory to the
more generic <linux/i2c/...> directory, and remove the spurious
dependency of this driver on OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patchis to add the first mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the first controller supports two slots, this patch
only support the first one right now.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to move pxamci DMA specific code to corresponding
platform layer because using DRCMRRXMMC/DRCMRTXMMC in pxamci.c makes
the driver code dedicated to platform which is not extensible.
It is applicable to all pxa platforms.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa3[0|1]0 mmc controller can support 26MHz clock mode, they support
SD spec 1.1 and MMC spec 4.0 which specify high speed mode. So host
caps will include MMC_CAP_MMC_HIGHSPEED and MMC_CAP_SD_HIGHSPEED for
pxa3[0|1]0.
This patch is to add 26MHz support for them. pxa host clock will be
set to 26MHz mode when the card supported max clock rate is higher
than or equal to 26MHz.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The JMicron JMB38x chip doesn't support transfers that aren't 32-bit
aligned (both size and start address). It also doesn't like switching
between PIO and DMA mode, so it needs to be reset after each request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers have been designed on the assumption that all transfers
will be 32-bit aligned, both in start address and in size. This is not a
guarantee the SDHCI specification provides and not one we can provide.
Revert back to PIO for individual requests in order to work around the
hardware bug.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Given the patch which simplifies the spi_sync calling convention, this one
updates the callers of that routine which tried using it according to the
previous specification. (Most didn't.)
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This also fixes a sparse warning about different signedness.
Only compile tested, because i do not have the hardware.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
mmc_init_queue only initializes the scatterlists with sg_init_table()
when using a bounce buffer. This leads to a BUG() when CONFIG_DEBUG_SG
is set.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move the code which marks the minor number as free to mmc_blk_put() so
that it happens on the final close() (or removal), instead of doing it
at removal even when the device is still logically open.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It is possible to handle arbitrary block sizes with tifm card reader by
conditionally switching to PIO in case such block has to be delivered. At
the beginning of each request, DMA is either disabled (non-power-of-2 block
size) or set to load time user preference.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some cards have been reported to signal that they're ready prematurely.
Checking both the busy bit and card state solves the issue.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Commit 45711f1a ("[SG] Update drivers to use sg helpers") had the
following bogus change in drivers/mmc/card/queue.c:
> - src_buf = page_address(src->page) + src->offset;
> + src_buf = sg_virt(dst);
(Notice that "src" is converted to "dst"). Turn this "dst" back into
the intended "src".
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix:
WARNING: at arch/arm/mach-pxa/clock.c:69 clk_disable()
[<c002d7c8>] (dump_stack+0x0/0x14) from [<c00334f4>] (clk_disable+0x34/0xa0)
[<c00334c0>] (clk_disable+0x0/0xa0) from [<c028a43c>] (pxamci_set_ios+0x74/0xf0)
[<c028a3c8>] (pxamci_set_ios+0x0/0xf0) from [<c0281548>] (mmc_power_off+0x90/0x9c)
[<c02814b8>] (mmc_power_off+0x0/0x9c) from [<c0281a30>] (mmc_start_host+0x18/0x28)
[<c0281a18>] (mmc_start_host+0x0/0x28) from [<c02825a0>] (mmc_add_host+0xe8/0x104)
[<c02824b8>] (mmc_add_host+0x0/0x104) from [<c028a7d0>] (pxamci_probe+0x24c/0x2f4)
[<c028a584>] (pxamci_probe+0x0/0x2f4) from [<c01e5948>] (platform_drv_probe+0x20/0x24)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
#include <scatterlist/scatterlist.h>
is an odd thing to do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch 49dce689ad changed the sysfs data
structures for SPI in a way which broke the MMC-over-SPI host driver.
This patch fixes that regression by changing the scheme used to keep
from knowingly trying to use a shared bus segment, and updates the
adjacent comments slightly to better explain the issue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
MMC over SPI sends the CID and CSD registers as data, not responses,
which means that the host driver won't do the necessary byte flipping
for us.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Do a full scan of the directory to try and be a bit more proactive,
instead of waiting for things to break.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commits
58b053e4ce ("Update arch/ to use sg helpers")
45711f1af6 ("[SG] Update drivers to use sg helpers")
fa05f1286b ("Update net/ to use sg helpers")
converted many files to use the scatter gather helpers without ensuring
that the necessary headerfile <linux/scatterlist> is included. This
happened to work for ia64, powerpc, sparc64 and x86 because they
happened to drag in that file via their <asm/dma-mapping.h>.
On most of the others this probably broke.
Instead of increasing the header file spider web I choose to include
<linux/scatterlist.h> directly into the affectes files.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A small MMC driver cleanup.
Use the defined AT91_MCI_ERRORS in at91_mci_completed_command() instead
of specifying all the error bits individually.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The exception path associated with an invalid ext_csd_struct returns
without freeing ext_csd.
Coverity CID 1909.
Signed-off-by: Florin Malita
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
AFAICS, fallout from repacing include of blkdev.h with include of bio.h.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the SPI framework and drivers stop using class_device. Update docs
accordingly ... highlighting just which sysfs paths should be
"safe"/stable.
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Otherwise we could have junk in the sg fields, fooling
the sg chaining into thinking ->page is valid.
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (95 commits)
[ARM] 4578/1: CM-x270: PCMCIA support
[ARM] 4577/1: ITE 8152 PCI bridge support
[ARM] 4576/1: CM-X270 machine support
[ARM] pxa: Avoid pxa_gpio_mode() in gpio_direction_{in,out}put()
[ARM] pxa: move pxa_set_mode() from pxa2xx_mainstone.c to mainstone.c
[ARM] pxa: move pxa_set_mode() from pxa2xx_lubbock.c to lubbock.c
[ARM] pxa: Make cpu_is_pxaXXX dependent on configuration symbols
[ARM] pxa: PXA3xx base support
[NET] smc91x: fix PXA DMA support code
[SERIAL] Fix console initialisation ordering
[ARM] pxa: tidy up arch/arm/mach-pxa/Makefile
[ARM] Update arch/arm/Kconfig for drivers/Kconfig changes
[ARM] 4600/1: fix kernel build failure with build-id-supporting binutils
[ARM] 4599/1: Preserve ATAG list for use with kexec (2.6.23)
[ARM] Rename consistent_sync() as dma_cache_maint()
[ARM] 4572/1: ep93xx: add cirrus logic edb9307 support
[ARM] 4596/1: S3C2412: Correct IRQs for SDI+CF and add decoding support
[ARM] 4595/1: ns9xxx: define registers as void __iomem * instead of volatile u32
[ARM] 4594/1: ns9xxx: use the new gpio functions
[ARM] 4593/1: ns9xxx: implement generic clockevents
...
Make sure the mmc_spi driver can build without CONFIG_BLOCK.
Issue noted by "Avuton Olrich" <avuton@gmail.com> and randconfig.
While that won't be a common configuration, sometimes embedded
boards use SDIO to interface WLAN or Bluetooth chips (vs some
parallel interface), and don't provide an MMC/SD socket for use
with flash memory cards.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (75 commits)
PM: merge device power-management source files
sysfs: add copyrights
kobject: update the copyrights
kset: add some kerneldoc to help describe what these strange things are
Driver core: rename ktype_edd and ktype_efivar
Driver core: rename ktype_driver
Driver core: rename ktype_device
Driver core: rename ktype_class
driver core: remove subsystem_init()
sysfs: move sysfs file poll implementation to sysfs_open_dirent
sysfs: implement sysfs_open_dirent
sysfs: move sysfs_dirent->s_children into sysfs_dirent->s_dir
sysfs: make sysfs_root a regular directory dirent
sysfs: open code sysfs_attach_dentry()
sysfs: make s_elem an anonymous union
sysfs: make bin attr open get active reference of parent too
sysfs: kill unnecessary NULL pointer check in sysfs_release()
sysfs: kill unnecessary sysfs_get() in open paths
sysfs: reposition sysfs_dirent->s_mode.
sysfs: kill sysfs_update_file()
...
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We register a simple trigger so make sure we use the corresponding
unregister function.
(Also means we get a dummy function when triggers aren't compiled in)
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Using weight32() to determine if a value is a power of 2 is a rather
heavi weight solution. The classic idiom is (x & (x - 1)) == 0, but
the kernel already provide a is_power_of_2 function for it.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The PXA has two transmit FIFOes, each32 byte deep. when one FIFO is
full and the other one has been transmitted, they are automatically
swapped and DMA is triggered for another 32 byte burst. However, when
there is less than 32 bytes left to send, the FIFO swap has to be done
manually. This is required for some SDIO transfers which are not
required to be multiples of 32 bytes.
A DMA completion interrupt is set for each descriptor which length isn't
a multiple of 32 in order to force the FIFO swap. While at it, the DMA
interrupt handler has been made a bit more resilient against errors.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently we print a message about some bad states wrt function IRQ
handlers but return 0 from process_sdio_pending_irqs() nevertheless.
This can lead to an infinite loop as nothing might have cleared the
condition for the pending card interrupt from the host controller by
the time host->ops->enable_sdio_irq(host, 1) is called.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
If func is actually null we won't get much from sdio_func_id(func).
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The forcedma and nodma module parameters can be replaced with the quirks
parameter, so remove the redundancy.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers like ENE712 can't work properly with DMA mode,
add this quirk to force these kinds of HW work with PIO mode
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Many host controllers don't fully follow the PCI spec to claim
whether they support DMA in PCI class register. Leave the driver
to judge it from the Capability register, quirks and module parameter
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Thanks to Matt Domsch and Rezwanul Kabir at Dell, we know how to disable the
MMC controller on the multi-function Ricoh R5C832. The MMC controller needs
to be disabled or it will steal MMC cards from the SD controller where they
would otherwise be supported by the Linux SDHCI driver.
Signed-off-by: Philipl Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The interrupt polling frequency is a compromise between power usage and
interrupt latency. Unfortunately, it affects throughput rather severely
for devices which require an interrupt for every chunk of data.
By making the polling frequency adaptive, we get better throughput with
those devices without sacficing too much power. Polling will quickly
increase when there is an actual interrupt, and slowly fall back to the
idle frequency when the interrupts stop coming.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Again, only available from PXA27x.
Signed-off-by: Bridge Wu <mingqiao.wu@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
From PXA27x, it is possible to do 4-bit data transfers.
Signed-off-by: Bridge Wu <mingqiao.wu@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
From PXA27x, it is possible to do 2048-byte block transfers.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Pending interrupts should be determined from both I_REG and I_MASK
registers.
Signed-off-by: Bridge Wu <mingqiao.wu@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The patch enables to define MMC host get_ro() method through platform data.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add a led trigger for each host controller that indicates if there
is a request active on the controller.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This is the latest version of the MMC-over-SPI support. It works
on 2.6.23-rc2 plus git-mmc (from rc1-mm2), along with the preceding
patches which teach the rest of the MMC stack about SPI.
The main issue of note is that sometimes cards need to be power cycled
to recover after certain faults. Also, it may sometimes be necessary
to disable CRCs. ("modprobe mmc_core use_spi_crc=n")
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: mikael.starvik@axis.com,
Cc: Hans-Peter Nilsson <hp@axis.com>
Cc: Jan Nikitenko <jan.nikitenko@gmail.com>
Cc: Mike Lavender <mike@steroidmicros.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Teach the MMC/SD/SDIO core about using SPI mode.
- Use mmc_host_is_spi() so enumeration works through SPI signaling
and protocols, not just the native versions.
- Provide the SPI response type flags with each request issued,
including requests from the new lock/unlock code.
- Understand that cmd->resp[0] and mmc_get_status() results for SPI
return different values than for "native" MMC/SD protocol; this
affects resetting, checking card lock status, and some others.
- Understand that some commands act a bit differently ... notably:
* OP_COND command doesn't return the OCR
* APP_CMD status doesn't have an R1_APP_CMD analogue
Those changes required some new and updated primitives:
- Provide utilities to access two SPI-only requests, and one
request that wasn't previously needed:
* mmc_spi_read_ocr() ... SPI only
* mmc_spi_set_crc() ... SPI only (override by module parm)
* mmc_send_cid() ... for use without broadcast mode
- Updated internal routines:
* Previous mmc_send_csd() modified into mmc_send_cxd_native();
it uses native "R2" responses, which include 16 bytes of data.
* Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
helper for command-and-data access
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
- Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper
- Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
those helper routines based on whether they're native or SPI
The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Teaching the MMC/SD block card driver about SPI.
- Provide the SPI response type flags with each request issued.
- Understand that multiblock SPI writes don't use STOP_TRANSMISSION.
- Correct check for APP_CMD failure.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Increase delay for power up in order to support some slower boards.
Also add some comments about why the delays are there.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
