Add support for the GPIO pins on the WM831x. No direct support is
currently supplied for configuring non-gpiolib functionality such
as pull configuration and alternate functions, soft configuration
of these will be provided in a future patch.
Currently use of these pins as interrupts is not supported due to
the ongoing issues with generic irq not support interrupt controllers
on interrupt driven buses. Users can directly request the interrupts
with the wm831x-specific APIs currently provided if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current settings which can be used with the WM831x current sinks
can't easily be mapped between register values and currents at run
time without a lookup table since the values scale logarithmically
to match the way the human eye interprets brightness. This lookup
table is inclided in the core since several drivers need to use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of devices use OTP (One Time Programmable, a type
of PROM) to store system configuration. At run time this data is
visible via registers.
Currently the only explicitly supported feature is that the unique
ID provided by every WM831x device is exported to user space via
sysfs. Other configuration data may be read by system-specific
code in the pre_init() and post_init() platform data operations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x backlight driver requires at least the specification of the
current sink to use and a maximum current to allow them to function and
will actively interfere with other users of the regulators it uses if
misconfigured so only register the subdevice for it if this platform
data has been supplied.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x contains an auxiliary ADC with a number of switchable
inputs which is used to monitor some of the voltages and
temperatures in the system and has some external inputs which can be
used for machine specific purposes. Provide an API allowing drivers
to read values from the ADC.
An internal reference voltage is provided to allow callibration of
the ADC. This is used to calibrate the device at startup.
The hardware also supports continuous readings and digital comparators.
These are not yet supported by the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x includes an interrupt controller managing interrupts for
the various functions on the chip. This patch adds support for the
core interrupt block on the device.
Ideally this would be supported by genirq, particularly for the
GPIOs, but currently genirq is unable to cope with controllers on
interrupt driven buses so we cut'n'paste the generic interface.
Once genirq is able to cope chips like this it should be a case
of filing the prefixes off the code and redoing wm831x-irq.c to
move over.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of devices are register compatible processor power
management subsystems, providing regulator and power path management
facilities along with other services like watchdog, RTC and touch
panel controllers.
This patch adds very basic support, providing basic single register
I2C access, handling of the security key and registration of the
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Provide basic support for MFDs having multiple cells of a given
type with different IDs by adding an id to the mfd_cell structure
and then adding that to the id passed in to mfd_add_devices().
As it stands this approach requires that MFDs using this feature
deal with ensuring that there aren't any ID collisions resulting
from multiple MFDs of the same type being instantiated. This needs
to happen with the existing code too, but with this approach there
is a knock on effect on the IDs for non-duplicated devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Register ezx-pcap earlier so it can be used with cpufreq
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch corrects the support for MMCSD card detection
and read only feature for SoC DM355.
EVMDM355_ECP_VA4.pdf, from Spectrum digital, suggests that
Bit 2 and 4 should be checked for card detection. However
on the EVM, bits 1 and 3 gives this status, for MMC/SD
instance 0 and 1 respectively. The pdf also suggests that
Bit 1 and 3 should be checked for write protection. However
on the EVM bits 2 and 4 gives this status.
This document can be downloaded from
http://c6000.spectrumdigital.com/evmdm355/reve/files/EVMDM355_ECP_VA4.pdf
Signed-off-by: Vipin Bhandari <vipin.bhandari@ti.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current implementation is prone to races, this patch attempts to remove all
but one (in pcf50633_adc_sync_read).
The idea is that we need to guard the queue access only on inserting and
removing items. If we insert and there're no more items in the queue it
means that the last irq already happened and we need to trigger ADC
manually. If not, then the next conversion will be triggered by the irq
handler upon completion of the previous.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Using the default kernel "events" workqueue causes problems with
synchronous adc readings if initiated from some task on the same
workqueue.
I had a deadlock trying to use pcf50633_adc_sync_read from a
power_supply class driver because the reading was initiated from the
workqueue and it waited for the irq processing to complete (to get the
result) and that was put on the same workqueue.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make that twl4030-pwrbutton.c driver probe with current
child creation api for twl4030.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides reporting of the status supply voltage rails
of the WM835x series of PMICs via the hwmon API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add (partial) support for the voltage regulators on the PCAP2 PMIC.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Provides an atomic set_bits functions, as needed by the pcap-regulator
driver.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mask interrupts before servicing them and loop while pcap asserts the interrupt
line.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some TS controller bits are on the same register as the ADC control, save
TS specific bits and export a set_ts_bits function so the TS driver can set
it with the adc_mutex lock held.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Export an irq_to_pcap function to get pcap irq number, for the keypad driver.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Driver Core: devtmpfs - kernel-maintained tmpfs-based /dev
debugfs: Modify default debugfs directory for debugging pktcdvd.
debugfs: Modified default dir of debugfs for debugging UHCI.
debugfs: Change debugfs directory of IWMC3200
debugfs: Change debuhgfs directory of trace-events-sample.h
debugfs: Fix mount directory of debugfs by default in events.txt
hpilo: add poll f_op
hpilo: add interrupt handler
hpilo: staging for interrupt handling
driver core: platform_device_add_data(): use kmemdup()
Driver core: Add support for compatibility classes
uio: add generic driver for PCI 2.3 devices
driver-core: move dma-coherent.c from kernel to driver/base
mem_class: fix bug
mem_class: use minor as index instead of searching the array
driver model: constify attribute groups
UIO: remove 'default n' from Kconfig
Driver core: Add accessor for device platform data
Driver core: move dev_get/set_drvdata to drivers/base/dd.c
Driver core: add new device to bus's list before probing
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pcmcia-2.6:
pcmcia: document return value of pcmcia_loop_config
pcmcia: dtl1_cs: fix pcmcia_loop_config logic
pcmcia: drop non-existant includes
pcmcia: disable prefetch/burst for OZ6933
pcmcia: fix incorrect argument order to list_add_tail()
pcmcia: drivers/pcmcia/pcmcia_resource.c: Remove unnecessary semicolons
pcmcia: Use phys_addr_t for physical addresses
pcmcia: drivers/pcmcia: Make static
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
Unfortunatly, the upstream company has abandonded development of this
driver. So it's best to just remove the driver from the tree.
Cc: Christopher Harrer <charrer@alacritech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Intel has officially abandoned this project and does not want to
maintian it or have it included in the main kernel tree, as no one
should use the code, it's not needed anymore.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is already an in-kernel driver for this hardware (since 2.6.30),
at76c50x-usb, and it supports all of the same devices. So this driver
can now be deleted.
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Cc: linux-wireless <linux-wireless@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No one cares, it's a custom userspace interface, and the code hasn't
built in a long time. So remove it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The comedi drivers should be used instead, no need to have
these in here as well.
Cc: David Kiliani <mail@davidkiliani.de>
Cc: Meilhaus Support <support@meilhaus.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The comedi drivers should be used instead, no need to have
this driver in the tree duplicating that one.
Cc: Wolfgang Beiter <w.beiter@aon.at>
Cc: Guenter Gebhardt <g.gebhardt@meilhaus.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
find_first_zero_bit returns a positive value, use it accordingly.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@xprog.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Error handling code following a kmalloc or kzalloc should free the
allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Error handling code following a kmalloc or kzalloc should free the
allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Similarly as it has been done in other in-kernel Ralink drivers
and in openSUSE's rt3090sta package.
Cc: Axel Koellhofer <rain_maker@root-forum.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch ports a change recently applied to rt2860/rt2870 in order to
change handling of WPA1/WPA2 mixed mode to rt3090.
Signed-off-by: Axel Koellhofer <rain_maker@root-forum.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch sets "wlan" as the default suffix for naming the device, a
change which has also been previously applied to rt2860/rt2870 in
staging.
Signed-off-by: Axel Koellhofer <rain_maker@root-forum.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both drivers (rt2860 and rt3090) register themselves as "rt2860" on
loading the module.
In the very rare case of somebody having two cards in his machine, one
using rt3090 and the other one using the rt2860 driver, loading both
modules would be impossible, the second one will not be loaded as the
kernel will tell you that the driver is already registered.
This was also present with rt2870/rt3070 (with both driver registering
as "rt2870"), but the code has been merged to one driver recently.
The follwoing patch fixes this potential problem until merging of
rt2860/rt3090 code to a single driver.
Signed-off-by: Axel Koellhofer <rain_maker@root-forum.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When compiling rt2860/rt2870/rt3070 or rt3090 on x86_64, the following warning
is displayed:
drivers/staging/rt3090/rt_linux.c: In function 'duplicate_pkt':
drivers/staging/rt3090/rt_linux.c:531: warning: passing argument 1 of 'memmove' makes pointer from integer without a cast
include2/asm/string_64.h:58: note: expected 'void *' but argument is of type 'sk_buff_data_t'
drivers/staging/rt3090/rt_linux.c:533: warning: passing argument 1 of 'memmove' makes pointer from integer without a cast
include2/asm/string_64.h:58: note: expected 'void *' but argument is of type 'sk_buff_data_t'
The following patch fixes this warning.
Credits go to Helmut Schaa <hschaa@suse.de> for his kind advice/help on this
patch.
Signed-off-by: Axel Koellhofer <rain_maker@root-forum.org>
Cc: Helmut Schaa <hschaa@suse.de>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds new device IDs to ralink rt2860 driver in linux staging. The
device IDs were retrieved from the latest vendor release (version 2.1.2.0).
Signed-off-by: Axel Koellhofer <rain_maker@root-forum.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new device ID (1462:819a) to ralink rt3090 driver in linux
staging. The device ID was retrieved from the latest vendor release (version
2.2.0.0).
Signed-off-by: Axel Koellhofer <rain_maker@root-forum.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kevin A. Granade <kevin.granade@gmail.com>
Cc: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The result of container_of should not be NULL. In particular, in this case
the argument to the enclosing function has passed though INIT_WORK, which
dereferences it, implying that its container cannot be NULL.
A simplified version of the semantic patch that makes this change is as
follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
identifier fn,work,x,fld;
type T;
expression E1,E2;
statement S;
@@
static fn(struct work_struct *work) {
... when != work = E1
x = container_of(work,T,fld)
... when != x = E2
- if (x == NULL) S
...
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the code is in the kernel tree, remove the unneeded version
checks.
Cc: "H.J. Thomassen" <hjt@ATComputing.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
