The i2c-ali1535 driver doesn't work on SPARC, because it assumes that
ioport address are 16-bit wide (address stored in an unsigned short).
But on SPARC arch, ioports are mapped in memory and so must be stored
in an unsigned long.
Use pci_resource_start for getting IOMEM base address, then read the
SMBBA of the i2c bus and use these together for I/O access.
I would like to thank Jean DELVARE for reviewing my patch.
Signed-off-by: LABBE Corentin <corentin.labbe@geomatys.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When adding checks for ACPI resource conflicts to many bus drivers,
not enough attention was paid to the error paths, and for several
drivers this causes 0 to be returned on error in some cases. Fix this
by properly returning a non-zero value on every error.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
This is a fix-style patch for i2c-ali1535 (issues reported by
checkpatch.pl.)
Signed-off-by: LABBE Corentin <corentin.labbe@geomatys.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As warned by checkpatch.pl, <linux/io.h> should be used instead of
<asm/io.h>.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The id_table field of the struct pci_driver is constant in <linux/pci.h>
so it is worth to make initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
with while (timeout++ < MAX_TIMEOUT); timeout reaches MAX_TIMEOUT + 1
after the loop, so the tests below are off by one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Check for ACPI resource conflicts in i2c bus drivers. I've included
all recent SMBus master drivers for PC hardware.
I've voluntarily left out:
* Drivers that don't run on PCs: they can't conflict with ACPI.
* Bit-banged bus device drivers: it's very unlikely that ACPI would
deal with such buses.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Let general purpose I2C/SMBus bus drivers add SPD to their class. Once
this is done, we will be able to tell the eeprom driver to only probe
for SPD EEPROMs and similar on these buses.
Note that I took a conservative approach here, adding I2C_CLASS_SPD to
many drivers that have no idea whether they can host SPD EEPROMs or not.
This is to make sure that the eeprom driver doesn't stop probing buses
where SPD EEPROMs or equivalent live.
So, bus driver maintainers and users should feel free to remove the SPD
class from drivers those buses never have SPD EEPROMs or they don't
want the eeprom driver to bind to them. Likewise, feel free to add the
SPD class to any bus driver I might have missed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Many PC SMBus host controller drivers don't properly handle the case
where they are requested to achieve a transaction they do not support.
Update them so that the consistently print a warning message and
return a single error value in this case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tighten error paths used by various i2c adapters (mostly x86) so
they return real fault/errno codes instead of a "-1" (which is
most often interpreted as "-EPERM"). Build tested, with eyeball
review.
One minor initial goal is to have adapters consistently return
the code "-ENXIO" when addressing a device doesn't get an ACK
response, at least in the probe paths where they are already
good at stifling related logspam.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This shrinks the size of "struct i2c_client" by 40 bytes:
- Substantially shrinks the string used to identify the chip type
- The "flags" don't need to be so big
- Removes some internal padding
It also adds kerneldoc for that struct, explaining how "name" is really a
chip type identifier; it's otherwise potentially confusing.
Because the I2C_NAME_SIZE symbol was abused for both i2c_client.name
and for i2c_adapter.name, this needed to affect i2c_adapter too. The
adapters which used that symbol now use the more-obviously-correct
idiom of taking the size of that field.
JD: Shorten i2c_adapter.name from 50 to 48 bytes while we're here, to
avoid wasting space in padding.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IDs have been defined but not used by most of the I2C adapters.
By having a unique ID, clients can check for correct connection
during probe.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c: Constify i2c_algorithm declarations, part 2
Make struct i2c_algorithm declarations const in all i2c bus drivers
where it is possible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop a redundant mutex in driver i2c-ali1535. The struct i2c_adapter
includes a mutex for the same purpose, operated by i2c-core.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanup after the semaphores to mutexes conversions in the i2c
subsystem.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch below converts a few i2c semaphores to mutexes
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates .owner field for various struct pci_driver variables.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up name string usage in 12 i2c bus drivers:
* Use the i2c_adapter name for requesting the I/O region rather than
redefining a new string.
* Do not initialize the i2c_adapter name to "unset".
This should save a few data bytes here and there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-ali1535.c | 6 +++---
drivers/i2c/busses/i2c-ali1563.c | 6 ++++--
drivers/i2c/busses/i2c-ali15x3.c | 5 +++--
drivers/i2c/busses/i2c-amd756.c | 5 ++---
drivers/i2c/busses/i2c-amd8111.c | 4 +++-
drivers/i2c/busses/i2c-i801.c | 4 ++--
drivers/i2c/busses/i2c-nforce2.c | 4 ++--
drivers/i2c/busses/i2c-piix4.c | 4 ++--
drivers/i2c/busses/i2c-sis5595.c | 5 +++--
drivers/i2c/busses/i2c-sis630.c | 6 ++++--
drivers/i2c/busses/i2c-sis96x.c | 5 +++--
drivers/i2c/busses/i2c-via.c | 4 ++--
12 files changed, 33 insertions(+), 25 deletions(-)
There are no more users of i2c_algorithm.id, so we can finally drop
this structure member.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The name member of the i2c_algorithm is never used, although all
drivers conscientiously fill it. We can drop it completely, this
structure doesn't need to have a name.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Files that don't use CONFIG_* stuff shouldn't include config.h
Files that use CONFIG_* stuff should include config.h
It's that simple. ;-)
Signed-off-by: Alexey Dobriyan <adobriyan@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
