We need to deassert rstctrl resets before enabling clocks to avoid clock
"failed to enable" errors. For asserting rstctrl reset, the clocks need
to be enabled.
As the reset controller status is not available for arrays, let's use
devm_reset_control_get_optional() so we can get the status after reset.
Note that depends on a proper PRM rstctrl driver, so far I've only
tested this with earlier reset-simple patches.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We must not assert reset for modules with no child device drivers
until in runtime_suspend. Otherwise register access will fail without
legacy mode helping us.
Let's add a flag for disable_on_idle and move the reset driver
handling to runtime suspend and resume. We can then also use the
disable_on_idle flag to reconfigure sysconfig register for PM
modes requesting it.
Let's also make the other flags use bitfield while at it instead of
bool.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules have ENAWAKEUP bit that we need to configure when not
relying on platform data callbacks.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules have idlemodes wired, but not completely functional. We have
quirks for SWSUP_SIDLE and SWSUP_SIDLE_ACT to manage interconnect target
modules without hardware support, but we've been only using them so far
in legacy mode. Let's add support for SWSUP quirks in non-legacy mode too.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For interconnect target modules with autoidle bit wired, we need to manage
it for enable and disable.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to specify QUIRK_LEGACY_IDLE for device drivers that still have
pm_runtime_irq_safe() set like 8250.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We've had minimal OCP softreset support in ti-sysc interconnect target
module driver only used for MCAN driver so far. But it turns out that
MCAN has the sysstatus register resetdone bit inverted compared to most
other modules.
Let's make OCP softreset work for other typical cases with reset status
in sysstatus or sysconfig register so we can use the new functions for
sysc_enable_module() and sysc_disable_module() without "ti,hwmods"
property in the following patches.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to also support 16-bit writes for i2c in addition to the reads
when we start configuring the sysconfig register for reset and idle modes.
Note that only i2c revision register has LO and HI registers, so let's
add a check also for 16-bit register read. This change is currently cosmetic
and does not affect anything until we enable the module specific quirk
handling for i2c reset and enable later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to let ti-sysc driver manage clockdomain autoidle for the
duration of of reset, enable and idle. And we need to do it before we
enable the clock and after we disable it. Currently we are still
relying on platform callbacks indirectly managing clockdomain autoidle.
But I noticed that for device tree only probed drivers it now happens
only after we enabling the clocks and before we disable the clocks,
while it should be the other way around. So far I have not noticed
any issues with this though.
Let's add new ti_sysc_clkdm_deny_idle() and ti_sysc_clkdm_allow_idle()
functions for ti-sysc driver to use to manage clockdomains directly via
platform data callbacks. Note that we can implement the clockdomain
functions in pdata-quirks.c as for probing devices without "ti,hwmods"
custom property we don't need to use the other platform data callbacks.
Let's do this in one patch as there's is still an unlikely chance we
may need to apply this as a fix for v5.2 for dropping legacy platform
data for some devices. We also do have the option of adding back the
platform data if needed in case of trouble.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers
-----BEGIN PGP SIGNATURE-----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=YSfu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC
suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
soc: aspeed: fix Kconfig
soc: add aspeed folder and misc drivers
spi: zynqmp: Fix build break
soc: imx: Add generic i.MX8 SoC driver
MAINTAINERS: Update email for Qualcomm SoC maintainer
memory: tegra: Fix a typos for "fdcdwr2" mc client
Revert "ARM: tegra: Restore memory arbitration on resume from LP1 on Tegra30+"
memory: tegra: Replace readl-writel with mc_readl-mc_writel
memory: tegra: Fix integer overflow on tick value calculation
memory: tegra: Fix missed registers values latching
ARM: tegra: cpuidle: Handle tick broadcasting within cpuidle core on Tegra20/30
optee: allow to work without static shared memory
soc/tegra: pmc: Move powergate initialisation to probe
soc/tegra: pmc: Remove reset sysfs entries on error
soc/tegra: pmc: Fix reset sources and levels
soc: amlogic: meson-gx-pwrc-vpu: Add support for G12A
soc: amlogic: meson-gx-pwrc-vpu: Fix power on/off register bitmask
fpga manager: Adding FPGA Manager support for Xilinx zynqmp
dt-bindings: fpga: Add bindings for ZynqMP fpga driver
firmware: xilinx: Add fpga API's
...
Some interconnect target modules have no module control registers at
all, such as d_can on am335x and am437x.
The d_can register offset at 0 is CTL register with 0x401 as the default
value. I guess I mistook the 0x401 value for a revision register as the
value happens to look similar to what the revision registers typically
have for other modules.
To handle modules with no control registers, we need to improve the
ti-sysc driver a bit to bail out with errors on no control registers,
and then we can remove the bogus revision registers for d_can.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For non legacy cases, add generic sysc_enable_module()
and sysc_disable_module() functions.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In preparation of dropping interconnect target module platform data in
favor of devicetree based data, we must pass swsup idle quirks to the
platform data functions.
For now, let's only tag the UART modules with the SWSUP_SIDLE_ACT quirk.
The other modules will get tagged with swsup quirks as we drop the
platform data and test the changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We cannot access mcpdm registers at all unless there is an optional pdmclk
configured. As this is currently only needed for mcpdm, let's check for
mcpdm in sysc_get_clocks(). If it turns out to be needed for other modules
too, we can add more flags to the quirks table for this.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least mcpdm needs an optional external clock enabled to function and
this clock typically comes from the PMIC. We can detect mcpdm based on
the interconnect target module address and set a quirk flag early.
To do this, let's initialize the clocks a bit later and add a new
function for sysc_init_early_quirks(). Note that we cannot yet enable
the early quirks for mcpdm until the optional external clocks are
handled in the in the following patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can do the rsstctrl a bit later, but need to deassert rstctrl reset
before the clocks are enabled if asserted. Let's only init restctrl
in sysc_init_resets() and do the reset later on just before we enable
the device clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are currently not managing interconnect target module clocks in the
for legacy platform data based case. This causes a problem for using the
platform data based functions when dropping the platform data for the
interconnect target module configuration.
To avoid a situation where we need to populate the main and optional
clocks also for the platform data based functions, let's just manage the
clocks directly in ti-sysc driver. This means that until the interconnect
target module confugration platform data is dropped our use count for
clk_enable() will be 2 instead of 1.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The platform data based init functions typically reset the interconnect
target module configure the registers. As we may need the interconnect
target module specific quirks configured based on the revision register,
we want to move the platform data based init to happen later.
Let's allocate mdata as needed so it's available for sysc_legacy_init()
that we call with module clocks enabled from sysc_init_module().
Signed-off-by: Tony Lindgren <tony@atomide.com>
The first thing we want to do is just read the module revision register to
be able to configure the module specific quirks and configure the module
registers.
As the interconnect target module may not yet be properly configured and
may need a reset first, we don't want to use pm_runtime_get() at this
point.
To read the revision register, let's just enable the all the clocks for
the interconnect target module during init even if the optional clocks
are not needed. That way we can read the revision register to configure
the quirks needed for PM runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least McPDM module depends on an external optional clock to be
usable. To make handling of the McPDM clock easier in the following
patches, let's add separate functions for handling the main clocks
and the optional clocks.
Let's also add error handling to shut down already enabled clocks
while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have ti,no-idle in use in addition to ti,no-idle-on-init but we're
missing handling for it in the ti-sysc interconnect target module driver.
Let's also group the idle defines together and update the binding
documentation for it.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we return early before ddata->clocks have been allocated we will get a
NULL pointer dereference in sysc_unprepare(). Let's fix this by returning
early when no clocks are allocated.
Fixes: 0eecc636e5 ("bus: ti-sysc: Add minimal TI sysc interconnect target driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
pm_runtime_force_suspend() and pm_runtime_force_resume() are used as system
sleep noirq suspend and resume callbacks. If the driver is active till late
suspend, where runtime PM cannot run, force suspend is essential for the
device. This makes sure that the device is put into low power state during
system wide PM transitions to sleep states.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
aconnect bus driver is using pm_clk_*() interface for managing clocks.
With this, clocks seem to be always ON. This happens on Tegra devices
which use BPMP co-processor to manage clock resources, where clocks
are enabled during prepare phase. This is necessary because calls to
BPMP are always blocking. When pm_clk_*() interface is used on such
Tegra devices, clock prepare count is not balanced till driver remove()
gets executed and hence clocks are seen ON always. Thus this patch
replaces pm_clk_*() with devm_clk_*() framework.
Suggested-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP,
NVIDIA, Amlogic and Qualcomm.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+DOl
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP, NVIDIA,
Amlogic and Qualcomm"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (113 commits)
tee: optee: update optee_msg.h and optee_smc.h to dual license
tee: add cancellation support to client interface
dpaa2-eth: configure the cache stashing amount on a queue
soc: fsl: dpio: configure cache stashing destination
soc: fsl: dpio: enable frame data cache stashing per software portal
soc: fsl: guts: make fsl_guts_get_svr() static
hwrng: make symbol 'optee_rng_id_table' static
tee: optee: Fix unsigned comparison with less than zero
hwrng: Fix unsigned comparison with less than zero
tee: fix possible error pointer ctx dereferencing
hwrng: optee: Initialize some structs using memset instead of braces
tee: optee: Initialize some structs using memset instead of braces
soc: fsl: dpio: fix memory leak of a struct qbman on error exit path
clk: tegra: dfll: Make symbol 'tegra210_cpu_cvb_tables' static
soc: qcom: llcc-slice: Fix typos
qcom: soc: llcc-slice: Consolidate some code
qcom: soc: llcc-slice: Clear the global drv_data pointer on error
drivers: soc: xilinx: Add ZynqMP power domain driver
firmware: xilinx: Add APIs to control node status/power
dt-bindings: power: Add ZynqMP power domain bindings
...
Pull crypto update from Herbert Xu:
"API:
- Add helper for simple skcipher modes.
- Add helper to register multiple templates.
- Set CRYPTO_TFM_NEED_KEY when setkey fails.
- Require neither or both of export/import in shash.
- AEAD decryption test vectors are now generated from encryption
ones.
- New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
fuzzing.
Algorithms:
- Conversions to skcipher and helper for many templates.
- Add more test vectors for nhpoly1305 and adiantum.
Drivers:
- Add crypto4xx prng support.
- Add xcbc/cmac/ecb support in caam.
- Add AES support for Exynos5433 in s5p.
- Remove sha384/sha512 from artpec7 as hardware cannot do partial
hash"
[ There is a merge of the Freescale SoC tree in order to pull in changes
required by patches to the caam/qi2 driver. ]
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
crypto: s5p - add AES support for Exynos5433
dt-bindings: crypto: document Exynos5433 SlimSSS
crypto: crypto4xx - add missing of_node_put after of_device_is_available
crypto: cavium/zip - fix collision with generic cra_driver_name
crypto: af_alg - use struct_size() in sock_kfree_s()
crypto: caam - remove redundant likely/unlikely annotation
crypto: s5p - update iv after AES-CBC op end
crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
crypto: caam - generate hash keys in-place
crypto: caam - fix DMA mapping xcbc key twice
crypto: caam - fix hash context DMA unmap size
hwrng: bcm2835 - fix probe as platform device
crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
crypto: chelsio - Fixed Traffic Stall
crypto: marvell - Remove set but not used variable 'ivsize'
crypto: ccp - Update driver messages to remove some confusion
crypto: adiantum - add 1536 and 4096-byte test vectors
crypto: nhpoly1305 - add a test vector with len % 16 != 0
crypto: arm/aes-ce - update IV after partial final CTR block
...
- Add compatibility support for different FWs in the hisi LPC bus driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f0/p
-----END PGP SIGNATURE-----
Merge tag 'hisi-drivers-for-5.1' of git://github.com/hisilicon/linux-hisi into arm/drivers
ARM64: hisi: SoC driver updates for 5.1
- Add compatibility support for different FWs in the hisi LPC bus driver
* tag 'hisi-drivers-for-5.1' of git://github.com/hisilicon/linux-hisi:
bus: hisi_lpc: Don't fail probe for unrecognised child devices
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Do not get GPCv2 driver depend on SOC_IMX8MQ since the driver is
going to be used on more SoCs than just i.MX8MQ.
- Add power domain information into SCU bindings document.
- Add support of start/stop a CPU into imx firmware driver.
- Support multiple address ranges per child node for imx-weim bus
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcYi+0AAoJEFBXWFqHsHzOtdYH/jX/y0r7OvX5GVSrrnW8PlkC
3i2EQ0sGOxWOMqBegZIpFe9W7IddAetMf6praPGz/efHPnoVC4jO8Yqe4TZwQXLB
vOxoN4G7NH9Al9RX11ce96kd/tUgVK/JHuQJ9fu+ogrprLpAS3w1sbIkidOMSF3M
/5VrmFCxUNOPwTHRnyjw8QsyypKnKEBu0jA8sgyUmg99ii6rqQ5OKh1vgKf62J0f
1BbJLalI0CxGcYVQxYBy2ML37+XxCcN9Vl8FxiI4tVRtZox8/YkU9V5vEgVWN2fS
ZWfgT9w7cJxI5x8Em8Cxe4zcyVdbn5w26lXc6WbXazIncm206Ps+DIeHkQI9jPA=
=8C2m
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers update for 5.1:
- Do not get GPCv2 driver depend on SOC_IMX8MQ since the driver is
going to be used on more SoCs than just i.MX8MQ.
- Add power domain information into SCU bindings document.
- Add support of start/stop a CPU into imx firmware driver.
- Support multiple address ranges per child node for imx-weim bus
driver.
* tag 'imx-drivers-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
firmware: imx: Add support to start/stop a CPU
soc: imx: Break dependency on SOC_IMX8MQ for GPCv2
firmware: imx: scu-pd: add fallback compatible string support
dt-bindings: fsl: scu: add imx8qm scu power domain support
dt-bindings: fsl: scu: add fallback compatible string for power domain
bus: imx-weim: guard against timing configuration conflicts
bus: imx-weim: support multiple address ranges per child node
dt-bindings: bus: imx-weim: document multiple address ranges per child node
soc: imx: gpcv2: handle reset clocks
soc: imx: gpcv2: handle additional power-down bits in handshake register
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently for ACPI-based FW we fail the probe for an unrecognised child
HID.
However, there is FW in the field with LPC child devices having fake HIDs,
namely "IPI0002", which was an IPMI device invented to support the
initial out-of-tree LPC host driver, different from the final mainline
version.
To provide compatibility support for these dodgy FWs, just discard the
unrecognised HIDs instead of failing the probe altogether.
Tested-by: Zengruan Ye <yezengruan@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Commit 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc") started producing a warning for pwm-omap-dmtimer:
WARNING: CPU: 0 PID: 77 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x2f8/0x388
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4PER2 (Idle):
Data Access in Supervisor mode during Functional access
...
__pm_runtime_idle
omap_dm_timer_disable
pwm_omap_dmtimer_start
pwm_omap_dmtimer_enable
pwm_apply_state
pwm_vibrator_start
pwm_vibrator_play_work
This is because the timer that pwm-omap-dmtimer is using is now being
probed with ti-sysc interconnect target module instead of omap_device
and the ti-sysc quirk for SYSC_QUIRK_LEGACY_IDLE is not fully
compatible with what omap_device has been doing.
We could fix this by reverting the timer changes and have the timer
probe again with omap_device. Or we could add more quirk handling to
ti-sysc driver. But as these options don't work nicely as longer term
solutions, let's just make timers probe with ti-sysc without any
quirks.
To do this, all we need to do is remove quirks for timers for ti-sysc,
and drop the bogus pm_runtime_irq_safe() flag for timer-ti-dm.
We should not use pm_runtime_irq_safe() anyways for drivers as it will
take a permanent use count on the parent device blocking the parent
devices from idling and has been forcing ti-sysc driver to use a
quirk flag.
Note that we will move the timer data to DEBUG section later on in
clean-up patches.
Fixes: 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe them with ti-sysc")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-By: Andreas Kemnade <andreas@kemnade.info>
Tested-By: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allocatable devices can be acquired by drivers on the fsl-mc bus using
the fsl_mc_portal_allocate or fsl_mc_object_allocate functions. Add a
device link between the consumer device and the supplier device so that
proper resource management is achieved.
Also, adding a link between these devices ensures that a proper unbind
order is respected (ie before the supplier device is unbound from its
respective driver all consumer devices will be notified and unbound
first).
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When specifying weim child devices, there is a risk that more than
one timing setting is specified for the same chip select.
The driver cannot support such a configuration.
In case of conflict, this patch will print a warning to the log,
and will ignore the child node in question.
In this example, node acme@1 will be ignored, as it tries to modify
timing settings for CS0:
&weim {
acme@0 {
compatible = "acme,whatever";
reg = <0 0 0x100>;
fsl,weim-cs-timing = <something>;
};
acme@1 {
compatible = "acme,whatnot";
reg = <0 0x500 0x100>;
fsl,weim-cs-timing = <something else>;
};
};
However in this example, the driver will be happy:
&weim {
acme@0 {
compatible = "acme,whatever";
reg = <0 0 0x100>;
fsl,weim-cs-timing = <something>;
};
acme@1 {
compatible = "acme,whatnot";
reg = <0 0x500 0x100>;
fsl,weim-cs-timing = <something>;
};
};
Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ensure that timing values for the child node are applied to
all chip selects in the child's address ranges.
Note that this does not support multiple timing settings per
child; this can be added in the future if required.
Example:
&weim {
acme@0 {
compatible = "acme,whatever";
reg = <0 0 0x100>, <0 0x400000 0x800>,
<1 0x400000 0x800>;
fsl,weim-cs-timing = <0x024400b1 0x00001010 0x20081100
0x00000000 0xa0000240 0x00000000>;
};
};
Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64 C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
+ misc cleanups across several platforms
-----BEGIN PGP SIGNATURE-----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=yEX2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64
C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in
GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
and misc cleanups across several platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: at91: add support in soc driver for new SAM9X60
ARM: at91: add support in soc driver for LPDDR2 SiP
memory: omap-gpmc: Use of_node_name_eq for node name comparisons
bus: ti-sysc: Check for no-reset and no-idle flags at the child level
ARM: OMAP2+: Check also the first dts child for hwmod flags
soc: amlogic: meson-clk-measure: Add missing REGMAP_MMIO dependency
soc: imx: gpc: Increase GPC_CLK_MAX to 7
soc: renesas: rcar-sysc: Fix power domain control after system resume
soc: renesas: rcar-sysc: Merge PM Domain registration and linking
soc: renesas: rcar-sysc: Remove rcar_sysc_power_{down,up}() helpers
soc: renesas: r8a77990-sysc: Fix initialization order of 3DG-{A,B}
dt-bindings: sram: sunxi: Add compatible for the A64 SRAM C1
dt-bindings: sram: sunxi: Add bindings for the H5 with SRAM C1
dt-bindings: sram: Add Allwinner suniv F1C100s
soc: sunxi: sram: Add support for the H5 SoC system control
soc: sunxi: sram: Enable EMAC clock access for H3 variant
soc: imx: gpcv2: add support for i.MX8MQ SoC
soc: imx: gpcv2: move register access table to domain data
soc: imx: gpcv2: prefix i.MX7 specific defines
dmaengine: pxa: make the filter function internal
...
This series of changes improves the TI module flag handling to allow
booting with older dts files until the module flags have been moved
to the interconnect target module level. And there's a of_node_name_eq()
clean-up patch from Rob Herring for the GPMC driver.
-----BEGIN PGP SIGNATURE-----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=xcO5
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.21/driver-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
Few more omap driver fixes and improvments for v4.21 merge window
This series of changes improves the TI module flag handling to allow
booting with older dts files until the module flags have been moved
to the interconnect target module level. And there's a of_node_name_eq()
clean-up patch from Rob Herring for the GPMC driver.
* tag 'omap-for-v4.21/driver-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
memory: omap-gpmc: Use of_node_name_eq for node name comparisons
bus: ti-sysc: Check for no-reset and no-idle flags at the child level
ARM: OMAP2+: Check also the first dts child for hwmod flags
Signed-off-by: Olof Johansson <olof@lixom.net>
With ti-sysc, we need to now have the device tree properties for
ti,no-reset-on-init and ti,no-idle-on-init at the module level instead
of the child device level.
Let's check for these properties at the child device level to enable
quirks, and warn about moving the properties to the module level.
Otherwise am335x-evm based boards tagging gpio1 with ti,no-reset-on-init
will have their DDR power disabled if wired up in such a tricky way.
Note that this should not be an issue for earlier kernels as we don't
rely on this until the dts files have been updated to probe with ti-sysc
interconnect target driver.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
for 4.21, please pull the following changes:
- James fixes the firmware interface after a commit changed the use of
VLA and broke large transfers
- Stefan adds a timeout check for Raspberry Pi firmware transactions and
updates a bunch of SoC/firmware files to use SPDX tags
- Wolfram switches the GISB bus arbiter to use dev_get_drvdata()
- Yangtao provides a fix for a reference leak due to a call to
of_find_node_by_path()
- Florian fixes the CPU re-entry point out of S3 suspend with kernels
built in Thumb2 mode
-----BEGIN PGP SIGNATURE-----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=yGiB
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.21/drivers' of https://github.com/Broadcom/stblinux into next/drivers
This pull request contains Broadcom ARM/ARM64/MIPS SoCs drivers changes
for 4.21, please pull the following changes:
- James fixes the firmware interface after a commit changed the use of
VLA and broke large transfers
- Stefan adds a timeout check for Raspberry Pi firmware transactions and
updates a bunch of SoC/firmware files to use SPDX tags
- Wolfram switches the GISB bus arbiter to use dev_get_drvdata()
- Yangtao provides a fix for a reference leak due to a call to
of_find_node_by_path()
- Florian fixes the CPU re-entry point out of S3 suspend with kernels
built in Thumb2 mode
* tag 'arm-soc/for-4.21/drivers' of https://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: Don't leak device tree node reference
firmware: raspberrypi: Switch to SPDX identifier
firmware: raspberrypi: Fix firmware calls with large buffers
soc: bcm: Switch raspberrypi-power to SPDX identifier
firmware: raspberrypi: Define timeout for transactions
bus: brcmstb_gisb: simplify getting .driver_data
soc: bcm: brcmstb: Fix re-entry point with a THUMB2_KERNEL
Signed-off-by: Olof Johansson <olof@lixom.net>
We have OPT_CLKS_NEEDED in legacy platform data, but it's missing
from the ti-sysc driver for device tree based configuration.
In order to pass OPT_CLKS_NEEDED quirk flag we need to update omap4 module
data and add a new compatible for dra7 as the module layout is different
from sysc_regbits_omap4_mcasp.
Fixes: 70a65240ef ("bus: ti-sysc: Add register bits for interconnect
target modules")
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can have holes in clock_roles with interface clock missing for
example. Currently getting an optional clock will fail if there are
only a functional clock and an optional clock.
Fixes: 09dfe58107 ("bus: ti-sysc: Add handling for clkctrl opt clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl" interface
that was a little controversial at first, but the version we merged
solved that by not exposing arbitrary firmware calls to user space.
- The Amlogic Meson platform gains a "canvas" driver that is used
for video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for
their respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in particular
a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem"
device driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=c/PQ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl"
interface that was a little controversial at first, but the version
we merged solved that by not exposing arbitrary firmware calls to
user space.
- The Amlogic Meson platform gains a "canvas" driver that is used for
video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for their
respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in
particular a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem" device
driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (129 commits)
firmware: tegra: bpmp: Implement suspend/resume support
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
MAINTAINERS: imx: include drivers/firmware/imx path
firmware: imx: add misc svc support
firmware: imx: add SCU firmware driver support
reset: Fix potential use-after-free in __of_reset_control_get()
dt-bindings: arm: fsl: add scu binding doc
soc: fsl: qbman: add interrupt coalesce changing APIs
soc: fsl: bman_portals: defer probe after bman's probe
soc: fsl: qbman: Use last response to determine valid bit
soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan
soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers
soc: fsl: qbman: Check if CPU is offline when initializing portals
reset: qcom: PDC Global (Power Domain Controller) reset controller
dt-bindings: reset: Add PDC Global binding for SDM845 SoCs
reset: Grammar s/more then once/more than once/
bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
...
