Rather then open coding a cache of the vibra control registers use the
regmap cache code. Also cache the interrupt mask register, providing
a small performance improvement for the interrupt code.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This will be used to support refactoring of the ASoC CODEC driver to use
a regmap.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
These functions are not referenced anywhere, nor prototyped, so just
remove them.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The default phase can meet most cards' requirement, but it is not the
optimal one. In some extreme situation, the rx phase point produced by
the following tuning process will drift quite a distance.
Before tuning UHS card, this patch will set a more proper initial tx
phase point, which is calculated from statistic data, and can achieve
a much better tx signal quality.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
These are the patches due for the MFD Next tree.
If there are any dramas with them, please let me know.
Kind regards,
Lee
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=e/El
-----END PGP SIGNATURE-----
Merge tag 'mfd-lee-3.12-1' of git://git.linaro.org/people/ljones/mfd
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Update copyright date, remove author address and add Roger Tseng.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Set a bit to enable rts5227 and rts5249 to enter a deeper internal
power-saving mode in S3, and recover it after resuming.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Clear hw_pfm_en to disable hardware PFM mode, to fix a bug that in some
situation registers in 0xFDxx domain can't be accessed.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
These actions are individual for each reader model, so should be put in
extra_init_hw instead of rtsx_pci_init_hw.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some actions to clear power state should be handled in .shutdown
callback in rtsx_pci_driver. This patch adopts the following measures to
catch this goal:
1. Add a function rtsx_pci_power_off to abstract the common ops in
.shutdown and .suspend
2. Add pcr->ops->force_power_down to fulfill the individual action for
each reader model
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Normally OEMs will set vendor setting to the config space of Realtek
card reader in BIOS stage. This patch reads the setting at the first,
and configure the internal registers according to it, to improve card
reader's compatibility condition.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TWL6032 PMIC has different IRQ status bits meaning.
Hence, add interrupt mapping table for the twl6032.
Signed-off-by: Oleksandr Dmytryshyn <oleksandr.dmytryshyn@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Create "struct twl6030_irq" and place all local variables inside it.
Also allocate twl6030_irq structure dynamically during initialization.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the TWL6030 PMIC is used with OMAP4 SoCs only and OMAP4 legacy
boot is dropped there are no needs to allocate the range of IRQ
descriptors during system boot to support TWL6030 IRQs.
Hence, convert it to use linear irq_domain and move IRQ configuration in
.map()/.unmap() callbacks of irq_domain. So, IRQ mapping and descriptors
allocation will be performed dynamically basing on DT configuration.
The error message will be reported in case if unmapped IRQ is received by
TWL6030 (virq==0).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a missed check for errors when TWL IRQs are masked
initially on probe and report an error in case of failure.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
1) Removed request_irq() and replaced it with request_threaded_irq().
2) Removed generic_handle_irq() and replaced it with
handle_nested_irq().
Handling of these interrupts is nested, as we are handling an
interrupt (for e.g rtc, mmc1) when we are still servicing TWL irq.
3) Removed I2C read-retry logic for the case when twl_i2c_read() is
failed inside IRQ handler - there is no sense to do that, so just report
an error and return.
4) Each nested IRQ is configured with corresponding parent_irq,
which need to be retriggered in case if nested IRQ is marked
as IRQS_PENDING.
Signed-off-by: Naga Venkata Srikanth V <vnv.srikanth@samsung.com>
Signed-off-by: Oleg_Kosheliev <oleg.kosheliev@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Include <linux/module.h> in order to fix the following errors.
drivers/mfd/pm8921-core.c:209:16: error: expected declaration specifiers or '...' before string constant
drivers/mfd/pm8921-core.c:210:20: error: expected declaration specifiers or '...' before string constant
drivers/mfd/pm8921-core.c:211:16: error: expected declaration specifiers or '...' before string constant
drivers/mfd/pm8921-core.c:212:14: error: expected declaration specifiers or '...' before string constant
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some of Palmas resources like clock, SMPSs, LDOs etc can be controlled
by external pins ENABLE1, ENABLE2 or NSLEEP.
Add support to configure these resources to externally controlled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a regmap irqchip for DA9063 IRQs. It depends on
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap.git tags/regmap-irq-ack-mask
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is MFD module providing access to registers and interrupts of DA906x
series PMIC. It is used by other functional modules, registered as MFD cells.
Driver uses regmap with paging to access extended register list. Register map
is divided into two pages, where the second page is used during initialisation.
This module provides support to following functional cells:
- Regulators
- RTC
- HWMON
- OnKey (power key misc input device)
- Vibration (force-feedback input device)
- Watchdog
- LEDs
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The reg_cache variable should be updated with current
steps in the reg_se register. Then the mask should
apply and clear the register. Previously, the reg_cache
can be an old redundant value that isn't updated.
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The child device intends to perform DMA operations then it needs a dma
mask and params set. This patches copies them from the parent device.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Holger Dengler <dengler@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no need to use a per CPU workqueue to poll, especially with the
5s delay used, so allow the scheduler to use any CPU.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds DMI system IDs for the new Kontron modules COMe-bHL6 and
COMe-cTH6 to the Kontron PLD driver.
Acked-by: Kevin Strasser <strassek@engr.orst.edu>
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Hook up "pm_power_off" to palmas power off routine if there is DT
property "ti,system-power-controller" defined, so platform which is
powered by this regulator can be powered off properly.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds clock to list of mfd cells for s2mps11 and DT documentation
for clock part.
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
FX_CTRL2 is a volatile register and should be marked as such, this patch
does so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The mic detect level registers are used from common code to configure
the button detection code. Add these registers to the defaults list and
mark them as readable for wm5110.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The FLL gains are present on all devices and controlled from common code
shared between them. This patch adds these registers into defaults list
for wm5110 and marks them as readable.
Reported-by: D.J. Barrow <dbarrow@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reg_cache variable is used to lock step enable register
from being accessed and written by both TSC and ADC
at the same time.
However, it isn't updated anywhere in the code at all.
If both TSC and ADC are used, eventually 1FFFF is always
written enabling all 16 steps uselessly causing a mess.
Patch fixes it by correcting the locks and updates the
variable by reading the step enable register
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we disable DCVDD before we mark the cache as cache only, we might
attempt to write to the chip whilst it is powered down and lose a write.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the build
warnings when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.
drivers/mfd/ab8500-gpadc.c:891:12: warning: 'ab8500_gpadc_suspend' defined but not used [-Wunused-function]
drivers/mfd/ab8500-gpadc.c:903:12: warning: 'ab8500_gpadc_resume' defined but not used [-Wunused-function]
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add CONFIG_PM_RUNTIME to runtime_suspend/runtime_resume functions
to fix the build warnings when CONFIG_PM_RUNTIME is not selected.
This is because runtime PM callbacks defined by SET_RUNTIME_PM_OPS
are only used when the CONFIG_PM_RUNTIME is enabled.
drivers/mfd/ab8500-gpadc.c:870:12: warning: 'ab8500_gpadc_runtime_suspend' defined but not used [-Wunused-function]
drivers/mfd/ab8500-gpadc.c:878:12: warning: 'ab8500_gpadc_runtime_resume' defined but not used [-Wunused-function]
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the build
warnings when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.
drivers/mfd/ucb1x00-core.c:672:12: warning: 'ucb1x00_suspend' defined but not used [-Wunused-function]
drivers/mfd/ucb1x00-core.c:704:12: warning: 'ucb1x00_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
'mmc_callback_data' and 'vtg' are pointers.
Fix the following sparse warning:
drivers/mfd/menelaus.c:445:43: warning: Using plain integer as NULL pointer
drivers/mfd/menelaus.c:469:20: warning: Using plain integer as NULL pointer
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
twl4030_power_configure_scripts(), twl4030_power_configure_resources(),
twl4030_power_probe() are used only in this file.
Fix the following sparse warnings:
drivers/mfd/twl4030-power.c:496:5: warning: symbol 'twl4030_power_configure_scripts' was not declared. Should it be static?
drivers/mfd/twl4030-power.c:512:5: warning: symbol 'twl4030_power_configure_resources' was not declared. Should it be static?
drivers/mfd/twl4030-power.c:556:5: warning: symbol 'twl4030_power_probe' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
'lpc_chipset_info' is used only in this file.
Fix the following sparse warning:
drivers/mfd/lpc_ich.c:216:21: warning: symbol 'lpc_chipset_info' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Casting (void *) data of max8997_pmic_dt_match is necessary,
because variable 'data' of struct 'of_device_id' is defined as
'const void *data'. Thus, pointer should be used instead of value.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is only called from this file so there is no need for it to be in the
global namespace and cause sparse to warn.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
