The i.MX31ADS supports pluggable PMU modules, including the WM835x based
Wolfson Microelectronics 1133-EV1. These boards provide power, audio,
RTC and watchdiog services to the system. This patch adds initial support
for those boards in I2C mode.
Currently support is limited by the available support for the features
of the i.MX31 in the mainline kernel. Some further work will be needed
once other PMU modules are supported and once there is SPI support.
Many of the regulator constraints will be sharable with other PMU
boards.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This example takes advantage of the possibility to use tables of iomux
configs.
This is inspired from mx1-mx2 iomux code. It allows a better code
readability.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This new implemenatation avoids that two physical pins are claimed by
the same driver (also with the the gpr hardware modes).
The gpio kernel lib is also called when a capable gpio pin is assigned
its gpio function.
The mxc_iomux_mode function is still here for backward compatibility but
should not be used anymore.
V2:
In the precendent revision, the iomux code was claiming a pin when its
hardware mode was changed. This was uncorrect: when the hardware mode is
changed, the pin must still be claimed through the iomux.
In order to have a pin working in mode hw2, we must fist issue the
mxc_iomux_set_gpr call and then the corresponding mxc_iomux_mode calls
with the FUNC mode (usually done with mxc_iomux_setup_multiple_pins).
The reverse calls must be done to fee the pins.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
... from both mx27ads.c and pcm038.c
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Several of the macros in mx31ads.h depend on mx31.h which is no longer
included in quite so many standard headers as it once was. Include it
directly so we can build.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX I2C driver has not yet been merged into mainline but it is
near to that and the device defintions don't depend directly on it
so we can add the devices now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch mimicks what Martin wrote on the mailing list:
* move arch/arm/mach-imx/include/mach/imxfb.h into
arch/arm/mach-mxc/include/mach/imxfb.h
* changes Kconfig so that CONFIG_FB_IMX is selectable
* adds a platform device (copied from some pengutronix
patches)
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on code from "Martin Fuzzey" <mfuzzey@gmail.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* define new CONFIG_ARCH_MX21 (this one is currently mutually exclusive to
CONFIG_ARCH_MX27, but this might change)
* splits one header file. Memory definitions, interrupt sources,
DMA channels are split into common part, i.MX27 specific and i.MX21
specific.
* guard access to UART5/UART6, which don't exist on i.MX21
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Here are some of the warnings that get fixed by this:
> 200 times: warning: cast adds address space to expression (<asn:2>)
twelve times: warning: symbol 'xxx' was not declared. Should it be static
two times: warning: symbol 'clock' shadows an earlier one
five times: warning: incorrect type in initializer (different address spaces)
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch only adds general clkdev support without actually switching
any MXC architecture to clkdev.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The context makes it clear already that these are clocks, so there's
no need for such a suffix. This patch only changes the clocks actually
used in the tree. The remaining clocks are renamed in the subsequent
architecture specific patches.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- rename mxc_clocks_init to architecture specific versions. This
allows us to have more than one architecture compiled in.
- call mxc_timer_init from clock initialisation instead from board
code
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We had 3 versions of this function in clock support for MX1/2/3
Use a single one instead. I picked the one from the MX3 as it seems
to calculate more accurate as the other ones. Also, on MX27 and MX31 mfn
can be negative, this hasn't been handled correctly on MX27 since now.
This patch has been tested on MX27 and MX31 and produces the same clock
frequencies for me.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* adds Kconfig variables
* specifies different physical address for i.MX21 because of the
different memory layouts
* disables support for UART5/UART6 in the i.MX serial driver
(the i.MX21 doesn't have those modules)
Based on code from "Martin Fuzzey" <mfuzzey@gmail.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* removed iomux-mx1-mx2.h completely
* distributes the former contents to four different files (iomux-mx1.h,
iomux-mx21.h, iomux-mx27.h and the file iomux-mx2x.h, which is common to
both i.MX21 and i.MX27).
* adds all documented IOMUX definitions for i.MX21 and i.MX27
* fixes a few that were wrong (PD14_AOUT_FEC_CLR, PE16_AF_RTCK).
* don't silenly include <linux/io.h>
* and fixes all collateral damage from above
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add gpio vbus detection to udc driver, by taking advantage
of the new gpio_vbus driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
CSB701 is one of baseboards that can be used with CSB726 SOM.
This currently adds support for button and LED on the board.
More to come later.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The typo was originally fixed by Mike Rapoport and missed. And is
later reported by Matthias Meier.
Signed-off-by: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The current use of these macros works well when the conversion is
entirely linear. In this case, we can be assured that the following
holds true:
__va(p + s) - s = __va(p)
However, this is not always the case, especially when there is a
non-linear conversion (eg, when there is a 3.5GB hole in memory.)
In this case, if 's' is the size of the region (eg, PAGE_SIZE) and
'p' is the final page, the above is most definitely not true.
So, we must ensure that __va() and __pa() are only used with valid
kernel direct mapped RAM addresses. This patch tweaks the code
to achieve this.
Tested-by: Charles Moschel <fred99@carolina.rr.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a fix for the following crash observed in 2.6.29-rc3:
http://lkml.org/lkml/2009/1/29/150
On ARM it doesn't make sense to trace a naked function because then
mcount is called without stack and frame pointer being set up and there
is no chance to restore the lr register to the value before mcount was
called.
Reported-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Tested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Cc: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Steven Rostedt <rostedt@home.goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a Non-cacheable Normal ARM executable memory type,
MT_MEMORY_NONCACHED.
On OMAP3, this is used for rapid dynamic voltage/frequency scaling in
the VDD2 voltage domain. OMAP3's SDRAM controller (SDRC) is in the
VDD2 voltage domain, and its clock frequency must change along with
voltage. The SDRC clock change code cannot run from SDRAM itself,
since SDRAM accesses are paused during the clock change. So the
current implementation of the DVFS code executes from OMAP on-chip
SRAM, aka "OCM RAM."
If the OCM RAM pages are marked as Cacheable, the ARM cache controller
will attempt to flush dirty cache lines to the SDRC, so it can fill
those lines with OCM RAM instruction code. The problem is that the
SDRC is paused during DVFS, and so any SDRAM access causes the ARM MPU
subsystem to hang.
TI's original solution to this problem was to mark the OCM RAM
sections as Strongly Ordered memory, thus preventing caching. This is
overkill: since the memory is marked as non-bufferable, OCM RAM writes
become needlessly slow. The idea of "Strongly Ordered SRAM" is also
conceptually disturbing. Previous LAKML list discussion is here:
http://www.spinics.net/lists/arm-kernel/msg54312.html
This memory type MT_MEMORY_NONCACHED is used for OCM RAM by a future
patch.
Cc: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These changes were included in the S3C audio header move but are not
directly related to it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the register defines for the sleep and power control
functions in the S3C64XX SYSCON register block.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add definitions for the EINT group registers and move the EINT IRQ
register definitions out of arch/arm/plat-s3c64xx/irq-eint.c so that
they are available for re-use with PM and the other code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the modem registers and a virtual mapping for the
modem block. This is is required as there are registers
that control the LCD block that need to be saved over
suspend as well as interrupt controls.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
As noted by Russell King, the sleep code path is not
elegant and makes use of leaving items on the stack
between calls.
Change the code that does the following:
if (s3c_cpu_save(regs_save) == 0) {
flush_cache_all();
S3C_PMDBG("preparing to sleep\n");
pm_cpu_sleep();
}
to simply call s3c_cpu_save, and let that do the
necessary calls to quiesce and sleep the system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Impact: __per_cpu_load available on all SMP capable archs
Percpu now requires three symbols to be defined - __per_cpu_load,
__per_cpu_start and __per_cpu_end. There were three archs which
didn't have it. Update them as follows.
* powerpc: can use generic PERCPU() macro. Compile tested for
powerpc32, compile/boot tested for powerpc64.
* ia64: can use generic PERCPU_VADDR() macro. __phys_per_cpu_start is
identical to __per_cpu_load. Compile tested and symbol table looks
identical after the change except for the additional __per_cpu_load.
* arm: added explicit __per_cpu_load definition. Currently uses
unified .init output section so can't use the generic macro. Dunno
whether the unified .init ouput section is required by arch
peculiarity so I left it alone. Please break it up and use PERCPU()
if possible.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Russell King <rmk@arm.linux.org.uk>
The definitions of S3C2412_IISMOD_SDF_MSB and S3C2412_IISMOD_SDF_LSB
are incorrect, being the same S3C2412_IISMOD_SDF_IIS which is the
only correct one in this series.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
p54: fix race condition in memory management
cfg80211: test before subtraction on unsigned
iwlwifi: fix error flow in iwl*_pci_probe
rt2x00 : more devices to rt73usb.c
rt2x00 : more devices to rt2500usb.c
bonding: Fix device passed into ->ndo_neigh_setup().
vlan: Fix vlan-in-vlan crashes.
net: Fix missing dev->neigh_setup in register_netdevice().
tmspci: fix request_irq race
pkt_sched: act_police: Fix a rate estimator test.
tg3: Fix 5906 link problems
SCTP: change sctp_ctl_sock_init() to try IPv4 if IPv6 fails
IPv6: add "disable" module parameter support to ipv6.ko
sungem: another error printed one too early
aoe: error printed 1 too early
net pcmcia: worklimit reaches -1
net: more timeouts that reach -1
net: fix tokenring license
dm9601: new vendor/product IDs
netlink: invert error code in netlink_set_err()
...
