This is really pxa27x specific and should be kept in pxa27x.c. With this
newly introduced function, the original set_resetgpio_mode() is deprecated.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* Modification of Kconfig to add the Option
* 1 new file : buffalo-wxl-setup.c
This file is inspired from the db-78xx0-setup.c already present.
The following is done:
- Configure MPP Lines for the plateform (see my patch for MPP)
This is taken from the stock kernel provided by buffalotech (the vendor)
- GigaBit Ethernet
- Sata
- Uart are initiallized in a different way than on the dev board as we
have one core only.
- USB
The kernel has been running for some days now on my plateform.
Signed-off-by: Sebastien Requiem <sebastien@kolios.dk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch is composed of two new files :
- mpp.c which is mainly inspired by the same file as in mach-kirkwood
- mpp.h that is written from the documentation provided by Marvell
http://www.marvell.com/products/processors/embedded/discovery_innovation/HW_MV78100_OpenSource.pdf
Moreover, due to some implementation problem, I have
defined some MPPX_UNUSED that offer developers the possibility
to SET MPP to some unused value (such as for Buffalo WXL).
Note: This patch doesn't support MV78200 yet (only 78100 MPP lines have
been written)
Signed-off-by: Sebastien Requiem <sebastien@kolios.dk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Enable the kirkwood SATA SoC interface on the eSATA SheevaPlug.
Signed-off-by: John Holland <john.holland@cellent-fs.de>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
--
Allow basic eSATA SheevaPlug board configuration and build.
Signed-off-by: John Holland <john.holland@cellent-fs.de>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
--
This patch fix the below build error for arm1026ej-s processor (IntegratorCP/arm1026ej-s board).
CC init/main.o
In file included from include/linux/highmem.h:8,
from include/linux/pagemap.h:10,
from include/linux/mempolicy.h:62,
from init/main.c:52:
arch/arm/include/asm/cacheflush.h:134:2: error: #error Unknown cache maintainence model
make[1]: *** [init/main.o] Erreur 1
make: *** [init] Erreur 2
Signed-off-by: Abdoulaye Walsimou Gaye <walsimou@walsimou.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It appears the wrong GPIO registers were used
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
The 'outer_cache' variable is needed by the outer_inv_range(),
outer_clean_range() and outer_flush_range() functions, which are
declared as inline in asm/cacheflush.h. Otherwise drivers built
as a loadable module, which access these functions, will have
an undefined symbol.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The platform data allocated with kmalloc() will become unreachable once
the init is complete, so it should be freed. The problem was discovered
by kmemleak.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the power LED on DNS-323 revision A1, and adds timer
support for (hopefully) both A1 and B1 revisions.
Power LED on revision A1 is active low and also requires GPIO 4 to be
low to work.
Tested on my DNS-323 revision A1.
I have set the default trigger to timer as that replicates the
behaviour of the original firmware, userspace can change the trigger
at the end of the boot process providing a useful indication that
booting has completed.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch add a GPIO LED named "ns_v2:blue:sata" which can be used to
enable or disable SATA activity LED blinking.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Internet and Network Space v2 boards are very close. The only
difference is that there is no USB type B plug wired on the Internet
Space v2.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch allow user-space to configure the switch power-off behaviour
via the gpiolib sysfs interface.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Inspired by the mach-ep93xx flattening work, there is really not
much difference between the OpenRD base and client board support
so they should be merged together.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The (void *) cast is not needed when setting dev.platform_data to the
address of the data. Remove the casts.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The (void *) cast is not needed when setting dev.platform_data to the
address of the data. Remove the casts.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The (void *) cast is not needed when setting dev.platform_data to the
address of the data. Remove the casts.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Fix wrong register in proc-arm6_7.S data abort handler
ARM: 5909/1: ARM: Correct the FPSCR bits setting when raising exceptions
ARM: 5904/1: ARM: Always generate the IT instruction when compiling for Thumb-2
ARM: 5907/1: ARM: Fix the reset on the RealView PBX Development board
mx35: add a missing comma in a pad definition
mx25: make the FEC AHB clk secondary of the IPG
mx25: fix time accounting
mx25: properly initialize clocks
mx25: remove unused mx25_clocks_init() argument
i.MX25: implement secondary clocks for uarts and fec
i.MX25: Allow secondary clocks in DEFINE_CLOCK
ARM: MX3: Fixed typo in declared enum type name.
MXC: Add AUDMUXv2 register decode to debugfs
mx31ads: Provide an IRQ range to the WM835x on the 1133-EV1 module
mx31ads: Provide a name for EXPIO interrupt chip
mx31ads: Allow enable/disable of switchable supplies
Currently the omap serial clocks are autoidled after 5 seconds.
However, this causes lost characters on the serial ports. As this
is considered non-standard behaviour for Linux, disable the timeout.
Note that this will also cause blocking of any deeper omap sleep
states.
To enable the autoidling of the serial ports, do something like
this for each serial port:
# echo 5 > /sys/devices/platform/serial8250.0/sleep_timeout
# echo 5 > /sys/devices/platform/serial8250.1/sleep_timeout
...
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I have found an access to already released memory in
clk_debugfs_register_one() function.
Signed-off-by: Marek Skuczynski <mareksk7@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
David Binderman ran the sourceforge tool cppcheck over the source code of the
new Linux kernel 2.6.33-rc6:
[./arm/mach-omap2/mux.c:492]: (error) Buffer access out-of-bounds
13 characters + 1 digit + 1 zero byte is more than 14 characters.
Also add a comment on mode0 name length in case new omaps
start using longer names.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
3630 has more mux signals than 34xx. The additional pins
exist in omap36xx_cbp_subset, but are not initialized
as the superset is missing these offsets. This causes
the following errors during the boot:
mux: Unknown entry offset 0x236
mux: Unknown entry offset 0x22e
mux: Unknown entry offset 0x1ec
mux: Unknown entry offset 0x1ee
mux: Unknown entry offset 0x1f4
mux: Unknown entry offset 0x1f6
mux: Unknown entry offset 0x1f8
mux: Unknown entry offset 0x1fa
mux: Unknown entry offset 0x1fc
mux: Unknown entry offset 0x22a
mux: Unknown entry offset 0x226
mux: Unknown entry offset 0x230
mux: Unknown entry offset 0x22c
mux: Unknown entry offset 0x228
Fix this by adding the missing offsets to omap3 superset.
Note that additionally the uninitialized pins need to be
skipped on 34xx.
Based on an earlier patch by Allen Pais <allen.pais@ti.com>.
Reported-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ensure valid clock pointer during GPMC init. Fixes compiler
warning about potential use of uninitialized variable.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ensure valid base address during IRQ init. Fixes compiler warning
about potential use of uninitialized variable.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP platforms(like OMAP3530) include DSP or other co-processors
for media acceleration. when carving out memory for the
accelerators we can end up creating a hole in the memory map
of sort:
<kernel memory><hole(memory for accelerator)><kernel memory>
To handle such a memory configuration ARCH_HAS_HOLES_MEMORYMODEL
has to be enabled. For further information refer discussion at:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15262.html.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit c98929c07a removed the clearing of the FPSCR[31:28] bits from the
vfp_raise_exceptions() function and the new bits are or'ed with the old
FPSCR bits leading to unexpected results (the original commit was
referring to the cumulative bits - FPSCR[4:0]).
Reported-by: Tom Hameenanttila <tmhameen@marvell.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current behaviour is to generate the IT instruction only for Thumb-2
code. However, the kernel helpers in entry-armv.S are compiled to ARM in
a unified syntax file (if THUMB2_KERNEL). Recent compilers warn about
missing IT instruction in unified assembly syntax files. The patch
changes the "-mimplicit-it" gas option to "always".
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The only usage of _toggle_gpio_edge_triggering is in
an #ifdef CONFIG_ARCH_OMAP1 block, so only provide it if
CONFIG_ARCH_OMAP1 is defined, too.
This fixes a compiler warning:
arch/arm/plat-omap/gpio.c:758: warning: '_toggle_gpio_edge_triggering' defined but not used
when compiling for ARCH_OMAP2, ARCH_OMAP3 or ARCH_OMAP4.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
