Seems that ATEN serial-to-usb devices using pl2303 exist with
different device ids. This patch adds a missing device ID so it
is recognised by the driver.
Signed-off-by: Marcel J.E. Mol <marcel@mesa.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Dell DW5570 is a re-branded Sierra Wireless MC8805 which will by
default boot with vid 0x413c and pid 0x81a3. When triggered QDL download
mode, the device switches to pid 0x81a6 and provides the standard TTY
used for firmware upgrade.
Cc: <stable@vger.kernel.org>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Johan Hovold <johan@kernel.org>
A short control transfer would currently fail to be detected, something
which could lead to stale buffer data being used as valid input.
Check for short transfers, and make sure to log any transfer errors.
Note that this also avoids leaking heap data to user space (TIOCMGET)
and the remote device (break control).
Fixes: 6ce7610478 ("USB: Driver for CH341 USB-serial adaptor")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The current implementation failed to detect short transfers when
attempting to read the line state, and also, to make things worse,
logged the content of the uninitialised heap transfer buffer.
Fixes: abf492e7b3 ("USB: kl5kusb105: fix DMA buffers on stack")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Revert to using direct register writes to set the divisor and
line-control registers.
A recent change switched to using the init vendor command to update
these registers, something which also enabled support for CH341A
devices. It turns out that simply setting bit 7 in the divisor register
is sufficient to support CH341A and specifically prevent data from being
buffered until a full endpoint-size packet (32 bytes) has been received.
Using the init command also had the side-effect of temporarily
deasserting the DTR/RTS signals on every termios change (including
initialisation on open) something which for example could cause problems
in setups where DTR is used to trigger a reset.
Fixes: 4e46c410e0 ("USB: serial: ch341: reinitialize chip on
reconfiguration")
Signed-off-by: Johan Hovold <johan@kernel.org>
A recent change added support for modifying the default line-control
settings, but did not make sure that the modified settings were used as
part of reconfiguration after a device has been reset during resume.
This caused a port that was open before suspend to be unusable until
being closed and reopened.
Fixes: ba781bdf86 ("USB: serial: ch341: add support for parity, frame
length, stop bits")
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix reset-resume handling which failed to resubmit the read and
interrupt URBs, thereby leaving a port that was open before suspend in a
broken state until closed and reopened.
Fixes: 1ded7ea47b ("USB: ch341 serial: fix port number changed after
resume")
Fixes: 2bfd1c96a9 ("USB: serial: ch341: remove reset_resume callback")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to stop the interrupt URB before returning on errors during
open.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The modem-control signals are managed by the tty-layer during open and
should not be asserted prematurely when set_termios is called from
driver open.
Also make sure that the signals are asserted only when changing speed
from B0.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The private baud_rate variable is used to configure the port at open and
reset-resume and must never be set to (and left at) zero or reset-resume
and all further open attempts will fail.
Fixes: aa91def41a ("USB: ch341: set tty baud speed according to tty
struct")
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
DTR and RTS will be asserted by the tty-layer when the port is opened
and deasserted on close (if HUPCL is set). Make sure the initial state
is not-asserted before the port is first opened as well.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at spcp8x5_open+0x30/0xd0 [spcp8x5]
Fixes: 619a6f1d14 ("USB: add usb-serial spcp8x5 driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The write URB was being killed using the synchronous interface while
holding a spin lock in close().
Simply drop the lock and busy-flag update, something which would have
been taken care of by the completion handler if the URB was in flight.
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in open() should a type-0 or type-1 device
lack the expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at pl2303_open+0x38/0xec [pl2303]
Note that a missing interrupt-in endpoint would have caused open() to
fail.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at oti6858_open+0x30/0x1d0 [oti6858]
Note that a missing interrupt-in endpoint would have caused open() to
fail.
Fixes: 49cdee0ed0 ("USB: oti6858 usb-serial driver (in Nokia CA-42
cable)")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The interrupt URB is killed at final port close since commit
0de9a7024e ("USB: overhaul of mos7840 driver").
Fixes: 0de9a7024e ("USB: overhaul of mos7840 driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at mos7840_open+0x88/0x8dc [mos7840]
Note that we continue to treat the interrupt-in endpoint as optional for
now.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit b69578df7e ("USB: usbserial: mos7720: add support for
parallel port on moschip 7715"), the interrupt urb is no longer
submitted at first port open and the endpoint-address initialisation at
port-probe is no longer used.
Signed-off-by: Johan Hovold <johan@kernel.org>
A static usb-serial-driver structure that is used to initialise the
interrupt URB was modified during probe depending on the currently
probed device type, something which could break a parallel probe of a
device of a different type.
Fix this up by overriding the default completion callback for MCS7715
devices in attach() instead. We may want to use two usb-serial driver
instances for the two types later.
Fixes: fb088e335d ("USB: serial: add support for serial port on the
moschip 7715")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Do not submit the interrupt URB until after the parport has been
successfully registered to avoid another use-after-free in the
completion handler when accessing the freed parport private data in case
of a racing completion.
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel
port on moschip 7715")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The interrupt URB was submitted on probe but never stopped on probe
errors. This can lead to use-after-free issues in the completion
handler when accessing the freed usb-serial struct:
Unable to handle kernel paging request at virtual address 6b6b6be7
...
[<bf052e70>] (mos7715_interrupt_callback [mos7720]) from [<c052a894>] (__usb_hcd_giveback_urb+0x80/0x140)
[<c052a894>] (__usb_hcd_giveback_urb) from [<c052a9a4>] (usb_hcd_giveback_urb+0x50/0x138)
[<c052a9a4>] (usb_hcd_giveback_urb) from [<c0550684>] (musb_giveback+0xc8/0x1cc)
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel
port on moschip 7715")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference at port open if a device lacks the expected
bulk in and out endpoints.
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
[<bf071c20>] (mos7720_open [mos7720]) from [<bf0490e0>] (serial_port_activate+0x68/0x98 [usbserial])
[<bf0490e0>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8)
[<c0470ca4>] (tty_port_open) from [<bf049d98>] (serial_open+0x48/0x6c [usbserial])
[<bf049d98>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc)
Fixes: 0f64478cbc ("USB: add USB serial mos7720 driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in write() should the device lack the
expected interrupt-out endpoint:
Unable to handle kernel NULL pointer dereference at virtual address 00000054
...
PC is at kobil_write+0x144/0x2a0 [kobil_sct]
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Check for the expected endpoints in attach() and fail loudly if not
present.
Note that failing to do this appears to be benign since da280e3488
("USB: keyspan_pda: clean up write-urb busy handling") which prevents a
NULL-pointer dereference in write() by never marking a non-existent
write-urb as free.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # < v3.3
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference at open should the device lack a bulk-in or
bulk-out endpoint:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at iuu_open+0x78/0x59c [iuu_phoenix]
Fixes: 07c3b1a100 ("USB: remove broken usb-serial num_endpoints
check")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Bind to the interface, but do not register any ports, after having
downloaded the firmware. The device will still disconnect and
re-enumerate, but this way we avoid an error messages from being logged
as part of the process:
io_ti: probe of 1-1.3:1.0 failed with error -5
Signed-off-by: Johan Hovold <johan@kernel.org>
Cancel the heartbeat work on driver unbind in order to avoid I/O after
disconnect in case the port is held open.
Note that the cancel in release() is still needed to stop the heartbeat
after late probe errors.
Fixes: 26c78daade ("USB: io_ti: Add heartbeat to keep idle EP/416
ports from disconnecting")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In case a device is left in "boot-mode" we must not register any port
devices in order to avoid a NULL-pointer dereference on open due to
missing endpoints. This could be used by a malicious device to trigger
an OOPS:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
[<bf0caa84>] (edge_open [io_ti]) from [<bf0b0118>] (serial_port_activate+0x68/0x98 [usbserial])
[<bf0b0118>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8)
[<c0470ca4>] (tty_port_open) from [<bf0b0da0>] (serial_open+0x48/0x6c [usbserial])
[<bf0b0da0>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc)
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference when clearing halt at open should a
malicious device lack the expected endpoints when in download mode.
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
[<bf011ed8>] (edge_open [io_ti]) from [<bf000118>] (serial_port_activate+0x68/0x98 [usbserial])
[<bf000118>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8)
[<c0470ca4>] (tty_port_open) from [<bf000da0>] (serial_open+0x48/0x6c [usbserial])
[<bf000da0>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc)
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference when initialising URBs at open should a
non-EPIC device lack a bulk-in or interrupt-in endpoint.
Unable to handle kernel NULL pointer dereference at virtual address 00000028
...
PC is at edge_open+0x24c/0x3e8 [io_edgeport]
Note that the EPIC-device probe path has the required sanity checks so
this makes those checks partially redundant.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to free the URB transfer buffer in case submission fails (e.g.
due to a disconnect).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference when clearing halt at open should the device
lack a bulk-out endpoint.
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at cyberjack_open+0x40/0x9c [cyberjack]
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
With gcc 4.1.2:
drivers/usb/serial/f81534.c: In function ‘f81534_port_probe’:
drivers/usb/serial/f81534.c:1250: warning: comparison is always false due to limited range of data type
f81534_logic_to_phy_port() may return a negative error value, which is
ignored by assigning it to u8 f81534_port_private.phy_num.
Use an intermediate variable of type int to fix this.
While at it, forward the actual error code instead of converting it to
-ENODEV, and drop the useless check for F81534_NUM_PORT, as the callee
always returns a valid port number in case of success.
Fixes: 0c9bd6004d ("USB: serial: add Fintek F81532/534 driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for PIDs 0x1040, 0x1041 of Telit LE922A.
Since the interface positions are the same than the ones used
for other Telit compositions, previous defined blacklists are used.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These updates include a new driver for Fintek F8153x devices, support
for the GPIO functionality on CP2105 devices, and improved support for
CH34X devices.
Included are also some clean ups and fixes for various minor issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=FChe
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.10-rc1
These updates include a new driver for Fintek F8153x devices, support
for the GPIO functionality on CP2105 devices, and improved support for
CH34X devices.
Included are also some clean ups and fixes for various minor issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Function klsi_105_open() calls usb_control_msg() (to "enable read") and
checks its return value. When the return value is unexpected, it only
assigns the error code to the return variable retval, but does not
terminate the exception path. This patch fixes the bug by inserting
"goto err_generic_close;" when the call to usb_control_msg() fails.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pan Bian <bianpan2016@163.com>
[johan: rebase on prerequisite fix and amend commit message]
Signed-off-by: Johan Hovold <johan@kernel.org>
Kill urbs and disable read before returning from open on failure to
retrieve the line state.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
On sparc32, tcflag_t is unsigned long, unlike all other architectures:
drivers/usb/serial/cp210x.c: In function 'cp210x_get_termios':
drivers/usb/serial/cp210x.c:717:3: warning: passing argument 2 of 'cp210x_get_termios_port' from incompatible pointer type
cp210x_get_termios_port(tty->driver_data,
^
drivers/usb/serial/cp210x.c:35:13: note: expected 'unsigned int *' but argument is of type 'tcflag_t *'
static void cp210x_get_termios_port(struct usb_serial_port *port,
^
Consistently use tcflag_t to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The BRIM Brothers Zone DPMX is a bicycle powermeter. This ID is for the USB
serial interface in its charging dock for the control pods, via which some
settings for the pods can be modified.
Signed-off-by: Paul Jakma <paul@jakma.org>
Cc: Barry Redmond <barry@brimbrothers.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop invalid user-pointer checks from ioctl handlers.
A NULL-pointer can be valid in user space and copy_to_user() takes care
of sanity checking.
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for the TI CC3200 LaunchPad board, which uses a
custom USB vendor ID and product ID. Channel A is used for JTAG, and
channel B is used for a UART.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Will probably be helpful if there are any more compatibility issues.
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
With the new reinitialization method, configuring parity, different
frame lengths and different stop bit settings should work as expected
on both CH340G and CH341A. Tested on a loopback-connected CH340G
with a logic analyzer in a number of different configurations.
Based on a patch by Grigori Goronzy
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
Changing the LCR register after initialization does not seem to be reliable
on all chips (particularly not on CH341A). Restructure initialization and
configuration to always reinit the chip on configuration changes instead and
pass the LCR register value directly to the initialization command.
(Note that baud rates above 500kbaud are incorrect, but they're incorrect in
the same way both before and after this patch at least on the CH340G. Fixing
this isn't a priority as higher baud rates don't seem that reliable anyway.)
Cleaned-up version of a patch by Grigori Goronzy
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
