Currently we are simply returning from target() if we encounter some error after
broadcasting CPUFREQ_PRECHANGE notifier. Which looks to be wrong as others might
depend on POSTCHANGE notifier for their functioning.
So, better broadcast CPUFREQ_POSTCHANGE notifier for these failure cases too,
but with old frequency.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is not possible for init() to be called for any cpu other than cpu0. During
bootup whatever cpu is used to boot system will be assigned as cpu0. And later
on policy->cpu can only change if we hotunplug all cpus first and then hotplug
them back in different order, which isn't possible (system requires atleast one
cpu to be up always :)).
Though I can see one situation where policy->cpu can be different then zero.
- Hot-unplug cpu 0.
- rmmod cpufreq-cpu0 module
- insmod it back
- hotplug cpu 0 again.
Here, policy->cpu would be different. But the driver doesn't have any dependency
on cpu0 as such. We don't mind which cpu of a system is policy->cpu and so this
check is just not required.
Remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use an inline function to evaluate freq_target to avoid duplicate code.
Also, define a macro for the default frequency step.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
clk_round_rate() returns singed value which was assigned to an unsigned
variable.
So it can't be checked for negative.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When we evaluate the CPU load for frequency decrease we have to compare
the load against down_threshold. There is no need to subtract 10 points
from down_threshold.
Instead, we have to use the default down_threshold or user's selection
unmodified.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
sampling_down_factor tunable is unused since commit
8e677ce83b (4 years ago).
This patch restores the original functionality and documents the
tunable.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently we always calculate the CPU iowait time and add it to idle time.
If we are in ondemand and we use io_is_busy, we re-calculate iowait time
and we subtract it from idle time.
With this patch iowait time is calculated only when necessary avoiding
the double call to get_cpu_iowait_time_us. We use a parameter in
function get_cpu_idle_time to distinguish when the iowait time will be
added to idle time or not, without the need of keeping the prev_io_wait.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.,org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The relation should be CPUFREQ_RELATION_L to find optimal frequency
when decreasing.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If we're on the lowest frequency, no need to calculate new freq.
Break out even earlier in this case.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Following patch has introduced per cpu timers or works for ondemand and
conservative governors.
commit 2abfa876f1
Author: Rickard Andersson <rickard.andersson@stericsson.com>
Date: Thu Dec 27 14:55:38 2012 +0000
cpufreq: handle SW coordinated CPUs
This causes additional unnecessary interrupts on all cpus when the load is
recently evaluated by any other cpu. i.e. When load is recently evaluated by cpu
x, we don't really need any other cpu to evaluate this load again for the next
sampling_rate time.
Some sort of code is present to avoid that but we are still getting timer
interrupts for all cpus. A good way of avoiding this would be to modify delays
for all cpus (policy->cpus) whenever any cpu has evaluated load.
This patch does this change and some related code cleanup.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because we have per cpu timer now, we check if we need to evaluate load again or
not (In case it is recently evaluated). Here the 2nd cpu which got timer
interrupt updates core_dbs_info->sample_type irrespective of load evaluation is
required or not. Which is wrong as the first cpu is dependent on this variable
set to an older value.
Moreover it would be best in this case to schedule 2nd cpu's timer to
sampling_rate instead of freq_lo or hi as that must be managed by the other cpu.
In case the other cpu idles in between then also we wouldn't loose much power.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently MIN_LATENCY_MULTIPLIER is set defined as 100 and so on a system with
transition latency of 1 ms, the minimum sampling time comes to be around 100 ms.
That is quite big if you want to get better performance for your system.
Redefine MIN_LATENCY_MULTIPLIER to 20 so that we can support 20ms sampling rate
for such platforms.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, there can't be multiple instances of single governor_type.
If we have a multi-package system, where we have multiple instances
of struct policy (per package), we can't have multiple instances of
same governor. i.e. We can't have multiple instances of ondemand
governor for multiple packages.
Governors directory in sysfs is created at /sys/devices/system/cpu/cpufreq/
governor-name/. Which again reflects that there can be only one
instance of a governor_type in the system.
This is a bottleneck for multicluster system, where we want different
packages to use same governor type, but with different tunables.
This patch uses the infrastructure provided by earlier patch and
implements init/exit routines for ondemand and conservative
governors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, there can't be multiple instances of single governor_type.
If we have a multi-package system, where we have multiple instances
of struct policy (per package), we can't have multiple instances of
same governor. i.e. We can't have multiple instances of ondemand
governor for multiple packages.
Governors directory in sysfs is created at /sys/devices/system/cpu/cpufreq/
governor-name/. Which again reflects that there can be only one
instance of a governor_type in the system.
This is a bottleneck for multicluster system, where we want different
packages to use same governor type, but with different tunables.
This patch is inclined towards providing this infrastructure. Because
we are required to allocate governor's resources dynamically now, we
must do it at policy creation and end. And so got
CPUFREQ_GOV_POLICY_INIT/EXIT.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This eliminates the contention I am seeing in __cpufreq_cpu_get.
It also nicely stages the lock to be replaced by the rcu.
Signed-off-by: Nathan Zimmer <nzimmer@sgi.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the addition of following patch:
fcf8058 cpufreq: Simplify cpufreq_add_dev()
cpufreq driver's .init() routine must initialize policy->cpus with
mask of all possible CPUs (Online + Offline) that share the clock.
Then the core would copy this mask onto policy->related_cpus and will
reset policy->cpus to carry only online cpus.
acpi-cpufreq driver wasn't updated with this assumption and so
sometimes when we try to hot[un]plug CPUs at run time, sysfs
directories get corrupted.
This patch fixes acpi-cpufreq driver against this corruption.
Reported-and-tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In cpufreq_stats_free_sysfs() we aren't balancing calls to
cpufreq_cpu_get() with cpufreq_cpu_put(). This will never let us have
ref count to policy->kobj as zero.
We will get a hang if somehow cpufreq_driver_unregister() is called.
And that can happen when we compile our driver as module and
insmod/rmmod it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
They are defined in coreboot (MSR_PLATFORM) and the other
one is already defined in msr-index.h.
Let's use those.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the correct pstate value to calculate the effective frequency.
References: https://bugzilla.redhat.com/show_bug.cgi?id=923942
Reported-by: Satish Balay <balay@fastmail.fm>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some VMs seem to try to implement some MSRs but not all the registers
the driver needs. Check to make sure all the MSR that we need are
available. If any of the required MSRs are not available refuse to
load.
References: https://bugzilla.redhat.com/show_bug.cgi?id=922923
Reported-by: Josh Stone <jistone@redhat.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It seems some VMs support the P state MSRs but return zeros. Fail
gracefully if we are running in this environment.
References: https://bugzilla.redhat.com/show_bug.cgi?id=916833
Reported-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If cpufreq_register_driver() fails just free memory that has been
allocated and return. intel_pstate_exit() function is removed since we
are built-in only now there is no reason for a module exit procedure.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As uninitialized array members will be initialized to zero, we can
avoid using a for loop by setting a value to it.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-By: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a typo in a comment in cpufreq_governor.h.
[rjw: Changelog]
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fixes for blackfin and microblaze build problems introduced by the
removal of global pm_idle. From Lars-Peter Clausen.
- OPP core build fix from Shawn Guo.
- Error condition check fix for the new imx6q-cpufreq driver from
Wei Yongjun.
- Fix for an AER driver crash related to the lack of APEI
initialization for acpi=off. From Rafael J. Wysocki.
- Fix for a USB breakage on Thinkpad T430 related to ACPI power
resources and PCI wakeup from Rafael J. Wysocki.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=FCbx
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-fixes-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Fixes for blackfin and microblaze build problems introduced by the
removal of global pm_idle. From Lars-Peter Clausen.
- OPP core build fix from Shawn Guo.
- Error condition check fix for the new imx6q-cpufreq driver from Wei
Yongjun.
- Fix for an AER driver crash related to the lack of APEI
initialization for acpi=off. From Rafael J Wysocki.
- Fix for a USB breakage on Thinkpad T430 related to ACPI power
resources and PCI wakeup from Rafael J. Wysocki.
* tag 'pm+acpi-fixes-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Take unusual configurations of power resources into account
imx6q-cpufreq: fix return value check in imx6q_cpufreq_probe()
PM / OPP: fix condition for empty of_init_opp_table()
ACPI / APEI: Fix crash in apei_hest_parse() for acpi=off
microblaze idle: Fix compile error
blackfin idle: Fix compile error
In case of error, the function devm_regulator_get() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Updates to the ux500 cpufreq code
* Moving the u300 DMA controller driver to drivers/dma
* Moving versatile express drivers out of arch/arm for sharing with arch/arm64
* Device tree bindings for the OMAP General Purpose Memory Controller
There is a simple conflict in drivers/cpufreq/dbx500-cpufreq.c, because
the mach/id.h header and the cpu_is_u8500_family() function in it are
now gone.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=R0p0
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
- Updates to the ux500 cpufreq code
- Moving the u300 DMA controller driver to drivers/dma
- Moving versatile express drivers out of arch/arm for sharing with arch/arm64
- Device tree bindings for the OMAP General Purpose Memory Controller
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: OMAP2+: gpmc: Add device tree documentation for elm handle
ARM: OMAP2+: gpmc: add DT bindings for OneNAND
ARM: OMAP2+: gpmc-onenand: drop __init annotation
mtd: omap-onenand: pass device_node in platform data
ARM: OMAP2+: Prevent potential crash if GPMC probe fails
ARM: OMAP2+: gpmc: Remove unneeded of_node_put()
arm: Move sp810.h to include/linux/amba/
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
ARM: OMAP: gpmc: enable hwecc for AM33xx SoCs
ARM: OMAP: gpmc-nand: drop __init annotation
mtd: omap-nand: pass device_node in platform data
ARM: OMAP: gpmc: don't create devices from initcall on DT
dma: coh901318: cut down on platform data abstraction
dma: coh901318: merge header files
dma: coh901318: push definitions into driver
dma: coh901318: push header down into the DMA subsystem
dma: coh901318: skip hard-coded addresses
dma: coh901318: remove hardcoded target addresses
dma: coh901318: push platform data into driver
dma: coh901318: create a proper platform data file
...
A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even specify
the driver they use, it can all get configured from the device tree
as we do for normal device drivers. The clocksource changes basically
touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose
their headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=DvgJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
When intel_pstate is configured into the kernel it will become the
preferred scaling driver for processors that it supports. Allow the
user to override this by adding:
intel_pstate=disable
on the kernel command line.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Load order is important in order for intel_pstate to take over as the
default scaling driver from acpi-cpufreq.
If both are built-in, acpi-cpufreq uses late_initcall() and
intel_pstate uses device_initcall() so it will be able to register as
the scaling before acpi-cpufreq for the processors supported by
intel_pstate.
If acpi-cpufreq is built as a module then intel_pstate still gets
first option to become the scaling driver.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* 'next/cpufreq-exynos' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
cpufreq: exynos: Fix hang in pm handler due to frequency mismatch
cpufreq: exynos: Initialize return variable
cpufreq: exynos: Fix unsigned variable being checked for negative value
cpufreq: exynos: Get booting freq value in exynos_cpufreq_init
cpufreq: exynos: Show list of available frequencies
cpufreq: exynos: Add missing static
cpufreq: exynos: Split exynos_target function into two functions
cpufreq: exynos: Use APLL_FREQ macro for cpu divider value
cpufreq: exynos: Check old & new frequency early
cpufreq: exynos: Remove unused variable & IS_ERR
* pm-cpufreq: (55 commits)
cpufreq / intel_pstate: Fix 32 bit build
cpufreq: conservative: Fix typos in comments
cpufreq: ondemand: Fix typos in comments
cpufreq: exynos: simplify .init() for setting policy->cpus
cpufreq: kirkwood: Add a cpufreq driver for Marvell Kirkwood SoCs
cpufreq/x86: Add P-state driver for sandy bridge.
cpufreq_stats: do not remove sysfs files if frequency table is not present
cpufreq: Do not track governor name for scaling drivers with internal governors.
cpufreq: Only call cpufreq_out_of_sync() for driver that implement cpufreq_driver.target()
cpufreq: Retrieve current frequency from scaling drivers with internal governors
cpufreq: Fix locking issues
cpufreq: Create a macro for unlock_policy_rwsem{read,write}
cpufreq: Remove unused HOTPLUG_CPU code
cpufreq: governors: Fix WARN_ON() for multi-policy platforms
cpufreq: ondemand: Replace down_differential tuner with adj_up_threshold
cpufreq / stats: Get rid of CPUFREQ_STATDEVICE_ATTR
cpufreq: Don't check cpu_online(policy->cpu)
cpufreq: add imx6q-cpufreq driver
cpufreq: Don't remove sysfs link for policy->cpu
cpufreq: Remove unnecessary use of policy->shared_type
...
There was a dangling #include <mach/id.h> in the cpufreq
file missing from commit
7a4f26097d
"ARM: ux500: de-globalize <mach/id.h>"
Causing build regressions when building with cpufreq
support.
Cc: arm@kernel.org
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes 32 bit build.
on i386:
drivers/built-in.o: In function `intel_pstate_timer_func':
intel_pstate.c:(.text+0x4ce97e): undefined reference to `__udivdi3'
drivers/built-in.o: In function `intel_pstate_cpu_init':
intel_pstate.c:(.cpuinit.text+0x974): undefined reference to `__udivdi3'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a couple of typos in comments.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix some typos in comments.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the recent changes in cpufreq core, we just need to set mask of all
possible cpus into policy->cpus. Rest would be done by core.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Marvell Kirkwood SoCs have simple cpufreq support in hardware. The
CPU can either use the a high speed cpu clock, or the slower DDR
clock. Add a driver to swap between these two clock sources.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a P-state driver for the Intel Sandy bridge processor. In cpufreq
terminology this driver implements a scaling driver with an internal
governor.
When built into the the kernel this driver will be the preferred
scaling driver for Sandy bridge processors.
In addition to the interfaces provided by the cpufreq subsystem for
controlling scaling drivers. The user may control the behavior of the
driver via three sysfs files located in
"/sys/devices/system/cpu/intel_pstate".
max_perf_pct: limits the maximum P state that will be requested by
the driver stated as a percentage of the avail performance.
min_perf_pct: limits the minimum P state that will be requested by
the driver stated as a percentage of the avail performance.
no_turbo: limits the driver to selecting P states below the turbo
frequency range.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The sysfs files for cpufreq_stats are created in cpufreq_stats_create_table()
called from cpufreq_stat_notifier_policy() when a policy is added to
the cpu. cpufreq_stats_create_table() will not be called if the
scaling driver does not export a frequency table to cpufreq. Use the
same fence on tear down.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Scaling drivers that implement internal governors do not have governor
structures assocaited with them. Only track the name of the governor
associated with the CPU if the driver does not implement
cpufreq_driver.setpolicy()
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Scaling drivers that implement cpufreq_driver.setpolicy() have
internal governors that do not signal changes via
cpufreq_notify_transition() so the frequncy in the policy will almost
certainly be different than the current frequncy. Only call
cpufreq_out_of_sync() when the underlying driver implements
cpufreq_driver.target()
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Scaling drivers that implement the cpufreq_driver.setpolicy() versus
the cpufreq_driver.target() interface do not set policy->cur.
Normally policy->cur is set during the call to cpufreq_driver.target()
when the frequnecy request is made by the governor.
If the scaling driver implements cpufreq_driver.setpolicy() and
cpufreq_driver.get() interfaces use cpufreq_driver.get() to retrieve
the current frequency.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq core uses two locks:
- cpufreq_driver_lock: General lock for driver and cpufreq_cpu_data array.
- cpu_policy_rwsemfix locking: per CPU reader-writer semaphore designed to cure
all cpufreq/hotplug/workqueue/etc related lock issues.
These locks were not used properly and are placed against their principle
(present before their definition) at various places. This patch is an attempt to
fix their use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On the lines of macro: lock_policy_rwsem, we can create another macro for
unlock_policy_rwsem. Lets do it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
