Update the Migo-R defconfig to include support for KEYSC, I2C, RTC and
NAND and NOR MTD devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH does not have a configuration option for NO_IDLE_HZ their Kconfig
files, yet their defconfig files lists them. Remove those references.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Solution Engine SH7721 board(MS7721RP01).
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The only board-specific bits that existed here were for setting up the
IRQs, which are now handled by the SH7710 CPU support code instead. As
there's nothing else to do for setup, kill off the board support code
and have the defconfig use the generic machvec instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This disables the PMB/32BIT=y by default in r7780mp, as turning this on
presently results in build errors (for an admittedly experimental
feature).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the defconfigs for r2d-plus and r2d-1 since we now have new drivers
for sm501 usb, spi-over-sci and epson r9701 rtc in mainline.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds basic support for the Migo-R board.
Only simple stuff provided by the cpu specific sh7722 code is in place now,
like serial console port, timers and usb gadget. There is also partial support
for the smc91c111 ethernet controller - unfortunately some driver header file
also needs patching (not included here) to make the driver get IRQ sense
information from the platform data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for Renesas Technology Europe SDK7780 board.
Signed-off-by: Nicholas Beck <nbeck@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch provides a correct value for CONFIG_SH_PCLK_FREQ for the
SH7712 solution engine when used with the board's default factory
settings. This results in the board running at its maximum CPU clock
rate (200 MHz).
Signed-off-by: Andrew Murray <amurray@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the ax88796 device driver to the r7785rp defconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the ax88796 device driver to the r7780mp defconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds basic support for SH-X3 SMP (4 CPUs).
More IPI and cache debugging is necessary, mostly interfacing the
d-cache coherency and the I-cache broadcast invalidates. Only for
testing at present!
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This update moves the flash mapping for the Magic Panel into the board
setup. It also removes references to the old MTD mapping option in the
defconfig.
Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7720 (SH3-DSP) based Magic Panel R2
board.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the old r2d config file named rts7751r2d_defconfig
and adds separate config files for the two r2d board versions. The two
new defconfigs are identical with the exception of board selection:
- rts7751r2dplus_defconfig selects CONFIG_RTS7751R2D_PLUS=y
- rts7751r2d1_defconfig selects CONFIG_RTS7751R2D_1=y
Please remember to update both files with r2d changes in the future.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes up the defconfig for various sh7751r based boards
by updating them to the single cpu subtype CONFIG_CPU_SUBTYPE_SH7751R.
The following sh4 boards are updated: hs7751rvoip, landisk, lboxre2,
systemh, titan.
The current defconfigs with two subtypes defined trigger a configuration
bug which result in kernel configurations with missing board support
code. We end up with kernels without board code and with generic machvec
only.
So we need this patch to make sure the board code gets compiled in.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- Disable CONFIG_SH_DMA to avoid boot up freeze on R2D-1
- Disable CONFIG_SH_STANDARD_BIOS to support R2D-PLUS boot loaders
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Updated the snapgear defconfig to get a booting kernel.
Signed-off-by: David McCullough <david_mccullough@au.securecomputing.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes old dead code:
- kill off sh7300 cpu support
- get rid of broken solution engine 7300 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes old dead code:
- kill off sh73180 cpu support
- get rid of broken solution engine 73180 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific 7750 setup code to use the
new intc controller. Many new vectors are added and multiple
processor variants including 7091, 7750, 7750s, 7750r, 7751 and
7751r should all have the correct vectors hooked up.
IRLM interrupts can be enabled using ipr_irq_enable_irlm() which
now is marked as __init.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the r2d board support in a few ways:
- CPU_SUBTYPE_SH7751R is selected in the defconfig to play well
with the r2d board Kconfig entry. Without this the defconfig
results in no board enabled.
- Enable EARLY_PRINTK.
- Enable SH_STANDARD_BIOS
- this works well for early printk on the r2d board.
- Add "earlyprink=bios" to the cmdline for early serial port
output by default.
- CONFIG_SUBTYPE_SH7751R support is added to the sh-specific
pci makefile.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific 7780 setup code to use the
new intc controller. Many new vectors are added and also support for
external interrupt sense configuration. So with this patch it is now
possible to configure external interrupt pins as edge or level
triggered using set_irq_type().
No external interrupts are registered by default.
Use plat_irq_setup_pins() to select between IRQ or IRL mode.
This patch also fixes the Alarm IRQ for the RTC.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch cleans up solution engine 7722 specific interrupt code.
The main purpose is to replace the mux function with use of
set_irq_chained_handler() and replace hard coded register poking
code with set_irq_type(). The board specific interrupts are also
moved to start from SE7722_FPGA_IRQ_BASE.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains two serial port related fixes for sh7722:
- Make sure the irqs for the first serial port is correct
- Add the second and third serial port to the platform data
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds more full-featured support for the SH7722 Solution Engine.
Previously this was using the generic board, and lacked most of the
peripheral support.
Signed-off-by: Ryusuke Sakato <sakato.ryusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up SH7705 CPU support and the SE7705 board
for some of the recent changes.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7780-based Solution Engine reference board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the L-BOX RE2 router.
http://www.nttcom.co.jp/l-box/
L-BOX RE2 is a SH7751R-based router. It has CF, Cardbus, serial,
and LAN x2. This is one of the very few SH boards that a general
person can obtain now.
The L-BOX shipped with a 2.4.28 kernel, this is a rewritten patch
adding it to current git.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7785-based Highlander board.
Some of the Highlander support code is reordered so that most of it
can be reused directly.
This also plugs in missing SH7785 checks in the places that need it,
as this is the first board to support the CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables the SM501 drivers for the R2D board. Additional
work needs to be done to migrate off of the VoyagerGX cchip
code to make use of the rest of the mfd infrastructure.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This tidies up some of the rts7751r2d mess and gets it booting
again. Update the defconfig, too.
Signed-off-by: Masayuki Hosokawa <hosokawa@ace-jp.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a new defconfig for SE7619 and updates SE7206.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the Solution Engine 7206 and 7619.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Small defconfig update for titan for 2.6.19-rc3, adding SH-RTC.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A few trivial updates for the microdev board support code:
- Update for __IO_PREFIX changes.
- Consolidate headers into a single microdev.h.
- Update the microdev_defconfig.
- Add init values for the S1D13806 used by s1d13xxxfb.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most of the reasons for keeping these separate before was due to hp690
discontig, and since we have a workaround for that now (abusing some shadow
space so everything is magically contiguous), there's no reason to keep the
targets separate.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
