Currently, the module does not initialize fully when the DIMMs aren't
ECC but remains still loaded. Propagate the error when no instance of
the driver is properly initialized and prevent further loading.
Reorganize and polish error handling in amd64_edac_init() while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Fix use-after-free errors by pushing all memory-freeing calls to the end
of amd64_remove_one_instance().
Reported-by: Darren Jenkins <darrenrjenkins@gmail.com>
LKML-Reference: <1261370306.11354.52.camel@ICE-BOX>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Fix the case when amd64_debug_display_dimm_sizes() reports only half the
amount of DRAM on it because it doesn't account for when the single DCT
operates in 128-bit mode and merges chip selects from different DIMMs.
Reported-by: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
LKML-Reference: <200912112202.48173.johannes.hirte@fem.tu-ilmenau.de>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This add supports for devices like keyboard, backlight, tablet and
accelerometer.
This work is supported by International Syst S/A.
[randy.dunlap@oracle.com: cmpc_acpi: depends on ACPI]
[akpm@linux-foundation.org: readability tweaks]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
With some of the cache rework an address aliasing optimization was added,
but this managed to fail on certain mappings resulting in pages with
PG_dcache_dirty set never writing back their dcache lines. This patch
reverts to the earlier behaviour of simply always writing back when the
dirty bit is set.
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
o remove unused define
o add device name comment
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ctrl_xxx() is an antiquated SH interface, while __raw_xxx is the standard
API that accomplishes the same thing. As such, this converts the
remaining sh-sci straggles over, which enables the driver to be wired up
for ARM SH-Mobile CPUs as well.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This establishes a sensible max baud rate for the earlyprintk cases where
the port's uartclk has not yet been determined.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that we have WMI autoloading
the DMI matching is not needed anymore.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Acked-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Len Brown <len.brown@intel.com>
There is no point in having the driver loaded in memory if we fail
to locate particular WMI GUID.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
These function allocate an acpi object by calling wmi_get_event_data, which
then calls acpi_evaluate_object, and it is not freed afterwards.
And kernel doc is fixed for parameters of wmi_get_event_data.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
BIOS information is now checked whether it begins with the strings stored
in the BIOS table. Previous method did a strcmp, what lead to problems if
BIOS information has appended whitespaces.
Signed-off-by: Peter Feuerer <peter@piie.net>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Andreas Mohr <andi@lisas.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Add new BIOS versions for following netbooks: Aspire 1810xx, Packard Bell
DOTMU.
Signed-off-by: Peter Feuerer <peter@piie.net>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
BugLink: https://bugs.launchpad.net/ubuntu/+bug/435958
The module alias currently matches any Acer computer but when loaded the
BIOS checks will only succeed on Aspire One models. This causes a invalid
BIOS warning for all other models (seen on Aspire 4810T). This is not
fatal but worries users that see this message. Limiting the moule alias
to models starting with AOA or DOA for Packard Bell.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Peter Feuerer <peter@piie.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Karol Kozimor <sziwan@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
In March 2008 commit 0ac4a3c2fb ("ACPI: fix
ATA_ACPI build") made CONFIG_ACPI_DOCK be selected by CONFIG_ATA_ACPI because
of a build error when CONFIG_ATA_ACPI=y and CONFIG_ACPI_DOCK=m.
However, in September 2008 commit 898b054f3e
("dock: make dock driver not a module") removed the possibility of having
CONFIG_ACPI_DOCK=m and therefore there is no need for selecting it when
CONFIG_ATA_ACPI=y.
This makes the kernel ~5 Kb smaller for people who don't have a dock by
allowing them to not have ACPI_DOCK compiled-in because of ATA_ACPI=y.
Signed-off-by: Carlos R. Mafra <crmafra@aei.mpg.de>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
SN06 makes sure we get back a longer buffer which seems to be necessary
going forward as the SNC devices describes more and more devices (or
features more precisely). Moreover SN06 should be called with only the
descriptor offset to make sure we hit the rfkill controlling function
(F124 or F135) with a 0 argument to get a full list of features.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Tested-by: Miguel Rodríguez Pérez <miguelrp@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Vaio Type X and possibly other new models use F135 as the radio
frequency controlling function attached to the SNC device. In the
indexed table this corresponds to 0x0135 (surpise!).
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'i2c-fixes' of git://git.fluff.org/bjdooks/linux:
i2c-omap: OMAP3: Fix I2C lockup during timeout/error cases
i2c-omap: Don't write IE state in unidle if 0
i2c-bfin-twi: fix CLKDIV calculation
In ocfs2_value_metas_in_xattr_header, we should Use
le16_to_cpu for ocfs2_extent_list.l_next_free_rec.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
I just noticed today that there are 2 places of "mlog(0,...)"
in fs/ocfs2/cluster/heartbeat.c, but actually have no default
mask prefix in that file.
So change them to mlog(ML_HEARTBEAT,...).
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
For fast symlink, it can be treated the same as inlined files since
the data extent we want to return of both case all were stored in
metadata block. For symlink, it can be simply treated the same as we
did for regular files.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>
Acked-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Current OMAP3 I2C driver code does not follow the correct sequence for soft
reset. Due to this, lock up issues are reported during timeout/error cases.
This patch fixes above issue by disabling I2C controller as per OMAP3430 TRM
for soft reset. As per TRM, I2C controller needs to be disabled as a first
step during soft reset.
Here is correct soft reset sequence:
a. Ensure that the module is disabled
(clear the I2Ci.I2C_CON[15] I2C_EN bit to 0).
b. Set the I2Ci.I2C_SYSC[1] SRST bit to 1.
c. Enable the module by setting I2Ci.I2C_CON[15] I2C_EN bit to 1.
d. Check the I2Ci.I2C_SYSS[0] RDONE bit until it is set to 1 to
indicate the software reset is complete.
Tested on Zoom2, Zoom3, 3430SDP and 3630SDP
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: George, Harith<harith@ti.com>
Acked-by: Varadarajan, Charu Latha<charu@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit ef871432... (i2c-omap: OMAP3: PM: (re)init for every transfer
to support off-mode) introduced a change which make the dev->iestate
contents be written to the OMAP_I2C_IE_REG every time omap_i2c_unidle
is called. Previously, the state was only written if it wasn't equal
to zero.
In omap_i2c_probe, omap_i2c_unidle() is called prior to omap_i2c_init(),
in which case dev->iestate has not yet been initialized and will be set
to zero. Having this value written to the registers causes deadlock
while booting.
As such, this change restores the original functionality.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Calculation of the CLKDIV speed setting should be done using base 10 math
rather than base 2. We also avoid exceeding the spec due to integer
truncation and a 50% duty cycle.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] use resource_size()
[WATCHDOG] iTCO_wdt: add PCI ID for the Intel EP80579 (Tolapai) SoC
This reverts commit 9f15226e75. It's just
wrong, and broke resume for Rafael even on a non-AMD CPU.
As Rafael says:
"... it causes microcode_init_cpu() to be called during resume even for
CPUs for which there's no microcode to apply. That, in turn, results
in executing request_firmware() (on Intel CPUs at least) which doesn't
work at this stage of resume (we have device interrupts disabled, I/O
devices are still suspended and so on).
If I'm not mistaken, the "if (uci->valid)" logic means "if that CPU is
known to us" , so before commit 9f15226e75 microcode_resume_cpu() was
called for all CPUs already in the system during suspend, which was
the right thing to do. The commit changed it so that the CPUs without
microcode to apply are now treated as "unknown", which is not quite
right.
The problem this commit attempted to solve has to be handled
differently."
Bisected-and -requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Executing _OSC returns a buffer, which has an acpi object in it.
Don't directly returns the buffer, instead, we return the acpi object's
buffer. This fixes a regression since caller of acpi_run_osc expects
an acpi object's buffer returned.
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
USB: Fix a bug on appledisplay.c regarding signedness
USB: option: support hi speed for modem Haier CE100
USB: audio gadget: free alsa devices when unloading
USB: audio gadget: fix wTotalLength calculation
usb: otg: isp1301_omap: fix compile error
USB: musb: workaround Blackfin FIFO anomalies
USB: musb: Fix array index out of bounds issue
USB: musb: Fix null pointer dereference issue
USB: musb: correct DMA address for tx
USB: musb: gadget_ep0: avoid SetupEnd interrupt
USB: musb: fix for crash in DM646x USB when (CPPI)DMA is enabled
USB: musb: do not work if no gadget driver is loaded
USB: musb: gadget: set otg tranceiver to idle when registering gadget
USB: musb: Populate the VBUS GPIO with the correct GPIO number
USB: musb: MAINTAINERS: Fix my tree's address
USB: musb: fix compiling warning with min() macro
USB: musb: move musb_remove to __exit
USB: musb_gadget: fix kernel oops in txstate()
USB: ftdi_sio: sort PID/VID entries in new ftdi_sio_ids.h header
USB: ftdi_sio: isolate all device IDs to new ftdi_sio_ids.h header
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
devtmpfs: unlock mutex in case of string allocation error
Driver core: export platform_device_register_data as a GPL symbol
driver core: Prevent reference to freed memory on error path
Driver-core: Fix bogus 0 error return in device_add()
Driver core: driver_attribute parameters can often be const*
Driver core: bin_attribute parameters can often be const*
Driver core: device_attribute parameters can often be const*
Doc/stable rules: add new cherry-pick logic
vfs: get_sb_single() - do not pass options twice
devtmpfs: Convert dirlock to a mutex
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging/vt66*: kconfig, depends on WLAN
Staging: batman-adv: introduce missing kfree
Staging: batman-adv: Add Kconfig dependancies on PROC_FS and PACKET.
Staging: panel: Adjust range for PANEL_KEYPAD in Kconfig
Staging: panel: Fix compilation error with custom lcd charset
Staging: ramzswap: remove ARM specific d-cache hack
Staging: rtl8192x: fix printk formats
Staging: wlan-ng: fix Correct size given to memset
staging: rtl8192su: add USB VID/PID for HWNUm-300
staging: fix rtl8192su compilation errors with mac80211
staging: fix rtl8192e compilation errors with mac80211
Staging: fix rtl8187se compilation errors with mac80211
Staging: rtl8192su: fix test for negative error in rtl8192_rx_isr()
Staging: comedi: jr3_pci: Don't ioremap too much space. Check result.
Staging: comedi: removed "depricated" from COMEDI_CB_BLOCK
Staging: comedi: usbdux.c: fix locking up of the driver when the comedi ringbuffer runs empty
Staging: dst: remove from the tree
Staging: sm7xx: add a new framebuffer driver
Staging: batman: fix debug Kconfig option
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: Set i_nlink properly during reflink.
ocfs2: Add reflinked file's inode to inode hash eariler.
ocfs2: refcounttree.c cleanup.
ocfs2: Find proper end cpos for a leaf refcount block.
The zone list code clearly cannot tolerate concurrent writers (I couldn't
find any locks for that), so simply add a global mutex. No need for RCU
in this case.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
When printing legacy sysctls print the warning message
for each of them only once. This way there is a guarantee
the syslog won't be flooded for any sane program.
The original attempt at this made the tables non const and stored
the flag inline.
Linus suggested using a separate hash table for this, this is based on a
code snippet from him.
The hash implies this is not exact and can sometimes not print a
new sysctl due to a hash collision, but in practice this should not
be a problem
I used a FNV32 hash over the binary string with a 32byte bitmap. This
gives relatively little collisions when all the predefined binary sysctls
are hashed:
size 256
bucket
length number
0: [25]
1: [67]
2: [88]
3: [47]
4: [22]
5: [6]
6: [1]
The worst case is a single collision of 6 hash values.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
It is unpredictable to have the same memory mapped using different
shared bit settings for ARMv6 and ARMv7 CPUs. Fix this for the CPU
write buffer bug test.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Kevin Hilman <khilman@ti.deeprootsystems.com>
Cc: Ulrik Bech Hald <ubh@ti.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Vincent Sanders <support@simtec.co.uk>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
brightness status is reported by the Apple Cinema Displays as an
'unsigned char' (u8) value, but the code used 'char' instead.
Note that he driver was developed on the PowerPC architecture,
where the two types are synonymous, which is not always the case.
Fixed that. Otherwise the driver will interpret brightness
levels > 127 as negative, and fail to load.
Signed-off-by: pancho horrillo <pancho@pancho.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
