Some Kconfig names were changed. This patch reapplies the rename script,
fixing for those drivers merged after the patch that renamed those
items.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] linux/libata.h: reorganize ata_device struct members a bit
ahci: SB600 ahci can't do MSI, blacklist that capability
libata: More TSSTcorp pain, keep in sync with legacy IDE
pata_via: Fix 6410 misdetect
[libata] pata_atiixp: fix PIO timing data misprogramming
Legacy HP ia64 platforms currently cannot provide
/proc/cpuinfo/physical_id due to legacy SAL/PAL implementations.
However, that physical topology information can be obtained
via ACPI.
Provide an interface that gives ACPI one last chance to provide
physical_id for these legacy platforms. This logic only comes
into play iff:
- ACPI actually provides slot information for the CPU
- we lack a valid socket_id
Otherwise, we don't do anything.
Since x86 uses the ACPI processor driver as well, we provide a nop
stub function for arch_fix_phys_package_id() in asm-x86/topology.h
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (28 commits)
V4L-DVB(7789a): cx18: fix symbol conflict with ivtv driver
V4L/DVB (7789): tuner: remove static dependencies on analog tuner sub-modules
V4L/DVB (7785): [2.6 patch] make mt9{m001,v022}_controls[] static
V4L/DVB (7786): cx18: new driver for the Conexant CX23418 MPEG encoder chip
V4L/DVB (7783): drivers/media/dvb/frontends/s5h1420.c: printk fix
V4L/DVB (7782): pvrusb2: Driver is no longer experimental
V4L/DVB (7781): pvrusb2-dvb: include dvb support by default and update Kconfig help text
V4L/DVB (7780): pvrusb2: always enable support for OnAir Creator / HDTV USB2
V4L/DVB (7779): pvrusb2-dvb: quiet down noise in kernel log for feed debug
Rename common tuner Kconfig names to use the same
Fix V4L/DVB core help messages
V4L/DVB (7769): Move other terrestrial tuners to common/tuners
V4L/DVB (7768): reorganize some DVB-S Kconfig items
V4L/DVB(7767): Move tuners to common/tuners
V4L/DVB (7766): saa7134: add another PCI ID for Beholder M6
V4L/DVB (7765): Add support for Beholder BeholdTV H6
V4L/DVB (7763): ivtv: add tuner support for the AverMedia M116
V4L/DVB (7762): ivtv: fix tuner detection for PAL-N/Nc
V4L/DVB (7761): ivtv: increase the DMA timeout from 100 to 300 ms
V4L/DVB (7759): ivtv: increase version number to 1.2.1
...
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Convert most new-style drivers to use module aliasing
i2c: Add support for device alias names
i2c-amd756-s4882: Fix an error path
i2c: Drop unused RTC driver IDs
i2c/tps65010: Add missing intialization of client data
i2c-sis5595: Minor cleanups in sis5595_access
i2c-piix4: Minor cleanups
i2c: Spelling fix (successful)
i2c-stub: No newline in parameter description
LD drivers/media/video/built-in.o
drivers/media/video/cx18/built-in.o: In function `get_service_set':
/home/v4l/tokernel/git/drivers/media/video/cx18/cx18-ioctl.c:118: multiple definition of `get_service_set'
drivers/media/video/ivtv/built-in.o:/home/v4l/tokernel/git/drivers/media/video/ivtv/ivtv-ioctl.c:119: first defined here
drivers/media/video/cx18/built-in.o: In function `expand_service_set':
/home/v4l/tokernel/git/drivers/media/video/cx18/cx18-ioctl.c:92: multiple definition of `expand_service_set'
drivers/media/video/ivtv/built-in.o:/home/v4l/tokernel/git/drivers/media/video/ivtv/ivtv-ioctl.c:92: first defined here
drivers/media/video/cx18/built-in.o: In function `service2vbi':
/home/v4l/tokernel/git/drivers/media/video/cx18/cx18-ioctl.c:44: multiple definition of `service2vbi'
drivers/media/video/ivtv/built-in.o:/home/v4l/tokernel/git/drivers/media/video/ivtv/ivtv-ioctl.c:42: first defined here
make[2]: ** [drivers/media/video/built-in.o] Erro 1
make[1]: ** [drivers/media/video] Erro 2
make: ** [drivers/media/] Erro 2
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the needlessly global mt9{m001,v022}_controls[] static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Many thanks to Steve Toth from Hauppauge and Nattu Dakshinamurthy from
Conexant for their support. I am in particular thankful to Hauppauge
since without their help this driver would not exist. It should also
be noted that Steve did the work to get the DVB part up and running.
Thank you!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: G. Andrew Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/dvb/frontends/s5h1420.c: In function `s5h1420_setsymbolrate':
drivers/media/dvb/frontends/s5h1420.c:484: warning: long long unsigned int format, u64 arg (arg 2)
We do not know what type the architecture uses for u64.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This driver has been in-kernel and reasonably stable for well over a
year. It is in a stable form and is known to work well. Remove its
experimental status.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This was a build option in the past, to avoid conflicts with the cxusb module
for digital televsion support. Now that dtv mode support has been merged into
pvrusb2, the OnAir devices are fully supported by this single module. This no
longer should be a build option.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Get rid of the noise in dmesg during dvb feed changes,
unless the appropriate debug trace flag is enabled.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Those tuners are currently used only under media/dvb. However,
they can support also analog TV. Better to move them to the same place
as the other hybrid tuners. This would make easier to use those tuners also
by analog drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are some DVB-S tuners together with DVB-S tags, while
others together with tuners. Better to have all of them together.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were several issues in the past, caused by the hybrid tuner design, since
now, the same tuner can be used by drivers/media/dvb and drivers/media/video.
Kconfig items were rearranged, to split V4L/DVB core from their drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When there is a lot of DMA traffic this timeout might sometimes be too low.
Increase it to be on the safe side.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Note that this card is only detected and not yet working.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tuner setup were happening during i2c attach callback. This means that it would
happen on two conditions:
1) if tuner module weren't load, it will happen at request_module("tuner");
2) if tuner is not compiled as a module, or it is already loaded
(for example, on setups with more than one tuner), it will happen
when saa7134 registers I2C bus.
Due to that, if tuner were loaded, tuner setup will happen _before_ reading
the proper values at tuner eeprom. Since set_addr refuses to change for a tuner
that were previously defined (except if the tuner_addr is set), this were
making eeprom tuner detection useless.
This patch removes tuner type setup from saa7134-i2c, moving it to the proper
place, after taking eeprom into account.
Reviewed-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tuner setup were happening during i2c attach callback. This means that it would
happen on two conditions:
1) if tuner module weren't load, it will happen at request_module("tuner");
2) if tuner is not compiled as a module, or it is already loaded
(for example, on setups with more than one tuner), it will happen
when cx88 registers I2C bus.
Due to that, if tuner were loaded, tuner setup will happen _before_ reading
the proper values at tuner eeprom. Since set_addr refuses to change for a tuner
that were previously defined (except if the tuner_addr is set), this were making
eeprom tuner detection useless.
This patch removes tuner type setup from cx88-i2c, moving it to the proper
place, after taking eeprom into account.
Reviewed-by: Gert Vervoort <gert.vervoort@hccnet.nl>
Reviewed-by: Ian Pickworth <ian@pickworth.me.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The discrete VIA ATA chips don't have 0x40 enable bits. We check that
properly in one location but not another. This causes some users 6410
RAID cards to be incorrectly skipped.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use correct variable, achieve desired result...
Spotted by LKML/linux-ide poster whose name I lost (apologies!)
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Based on earlier work by Jon Smirl and Jochen Friedrich.
This patch allows new-style i2c chip drivers to have alias names using
the official kernel aliasing system and MODULE_DEVICE_TABLE(). At this
point, the old i2c driver binding scheme (driver_name/type) is still
supported.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
tps65010_remove() calls i2c_get_clientdata(client) but the client data
is never set during initialization, so it gets a NULL pointer at best.
I guess it was never spotted because the tps65010 driver is typically
not built modular so this function is discarded.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
* Remove a needless include.
* Remove a legacy comment in piix4_access.
* Minor optimization in piix4_access.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Formatting cleanup
RDMA/nes: Add support for SFP+ PHY
RDMA/nes: Use LRO
IPoIB: Copy child MTU from parent
IB/mthca: Avoid changing userspace ABI to handle DMA write barrier attribute
IB/mthca: Avoid recycling old FMR R_Keys too soon
mlx4_core: Avoid recycling old FMR R_Keys too soon
IB/ehca: Allocate event queue size depending on max number of CQs and QPs
IPoIB: Use separate CQ for UD send completions
IB/iser: Count FMR alignment violations per session
IB/iser: Move high-volume debug output to higher debug level
IB/ehca: handle negative return value from ibmebus_request_irq() properly
RDMA/cxgb3: Support peer-2-peer connection setup
RDMA/cxgb3: Set the max_mr_size device attribute correctly
RDMA/cxgb3: Correctly serialize peer abort path
mlx4_core: Add a way to set the "collapsed" CQ flag
We don't need init_hwif_ali15x3() on the PowerPC systems either.
Before:
ALI15X3: IDE controller (0x10b9:0x5229 rev 0xc8) at PCI slot 0001:03:1f.0
ALI15X3: 100% native mode on irq 19
ide0: BM-DMA at 0x1120-0x1127
ide1: BM-DMA at 0x1128-0x112f
hda: SONY DVD RW AW-Q170A, ATAPI CD/DVD-ROM drive
hda: UDMA/66 mode selected
ide0: Disabled unable to get IRQ 14.
ide0: failed to initialize IDE interface
ide1: Disabled unable to get IRQ 15.
ide1: failed to initialize IDE interface
After:
ALI15X3: IDE controller (0x10b9:0x5229 rev 0xc8) at PCI slot 0001:03:1f.0
ALI15X3: 100% native mode on irq 19
ide0: BM-DMA at 0x1120-0x1127
ide1: BM-DMA at 0x1128-0x112f
hda: SONY DVD RW AW-Q170A, ATAPI CD/DVD-ROM drive
hda: UDMA/66 mode selected
ide0 at 0x1100-0x1107,0x110a on irq 19
ide1 at 0x1110-0x1117,0x111a on irq 19
hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
ide0 works well, though I can't test ide1, it isn't traced out on
the board.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some change to the IDE layer are causing the siimage driver to crash
at boot with a NULL dereference. This is due to the sil_dma_ops not
containing all the necessary pointers. I suppose it used to just
"override" the defaults while now, it needs to contain everything.
[bart: while at it: sil_dma_ops should be const now (pointed out by Sergei)]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
