This is a device driver for the NAND flash controller found on the various
DaVinci family chips. It handles up to four SoC chipselects, and some
flavors of secondary chipselect (e.g. based on upper bits of the address
bus) as used with some multichip packages. (Including the 2 GiB chips
used on some TI devel boards.)
The 1-bit ECC hardware is supported (3 bytes ECC per 512 bytes data); but
not yet the newer 4-bit ECC (10 bytes ECC per 512 bytes data), as
available on chips like the DM355 or OMAP-L137 and needed with the more
error-prone MLC NAND chips.
This is a cleaned-up version of code that's been in use for several years
now; sanity checked with the new drivers/mtd/tests.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The syndrome based page read/write routines store ECC, and possibly other
"OOB" data, right after each chunk of ECC'd data. With ECC chunk size of
512 bytes and a large page (2KiB) NAND, the layout is:
data-0 OOB-0 data-1 OOB-1 data-2 OOB-2 data-3 OOB-3 OOB-leftover
Where OOBx is (prepad, ECC, postpad). However, the current "raw" routines
use a traditional layout -- data OOB, disregarding the prepad and postpad
values -- so when they're used with that type of ECC hardware, those calls
mix up the data and OOB. Which means, in particular, that bad block
tables won't be found on startup, with data corruption and related chaos
ensuing.
The current syndrome-based drivers in mainline all seem to use one chunk
per page; presumably they haven't noticed such bugs.
Fix this, by adding read/write page_raw_syndrome() routines as siblings of
the existing non-raw routines; "raw" just means to bypass the ECC
computations, not change data and OOB layout.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The bf5xx_nand_add_partition() func is only called by __devinit functions,
so put it into the __devinit section as well
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Only set DMAC1_PERIMUX once we have requested and been granted the dma
channel to prevent breaking other peripherals in the error case
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The benet driver is now in the proper place in drivers/net/benet, so we
can remove the staging version.
Acked-by: Sathya Perla <sathyap@serverengines.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "c-enter" USB to Toshiba 1.8" IDE enclosure needs special treatment
to work flawlessly. This patch is absolutely trivial, as the integrated
USB-IDE bridge is already identified to be an "unusual" device, only the
bcdDevice is different (lower) to the bcdDeviceMin already included in
the kernel.
It is a Prolific 2507 bridge.
T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=067b ProdID=2507 Rev= 0.01
S: Manufacturer=Prolific Technology Inc.
S: Product=ATAPI-6 Bridge Controller
S: SerialNumber=00000272
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Thomas Bartosik <tbartdev@gmx-topmail.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Option GTM380 in Modem mode uses Product ID 0x7201. This has been tested and works
on production systems for over 6 months.
Signed-off-by: Achilleas Kotsis <akots@exponent.gr>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* newer versions of the Novatel Wireless U727 CDMA 3G USB stick
have a different Product ID (0x5010); adding this ID makes them
work just fine with the option driver
Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current firmware revision 5.60 still behaves the same,
so update the quirk up a (non-existing) 99.99 revision.
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=493415
Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Tested-by: Jan Heitkoetter <devnull@heitkoetter.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
The generic cdc-acm driver is now the best one to handle Sony Ericsson
F3507g-based devices (which the Dell 5530 is a rebrand of), now that all
the pieces are in place (ie, cac477e8f1).
Removing the IDs from option allows cdc-acm to handle the device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1225) fixes a bug in ehci-hcd. The condition for
whether unlinked QHs can become IDLE should not be that the controller
is halted, but rather that the controller isn't running. In other
words when the root hub is suspended, the hardware doesn't own any
QHs.
This fixes a problem that can show up during hibernation: If a QH is
only partially unlinked when the root hub is frozen, then when the
root hub is thawed the QH won't be in the IDLE state. As a result it
can't be used properly for new URB submissions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Brandon Philips <brandon@ifup.org>
Tested-by: Brandon Philips <brandon@ifup.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ehci-hcd uses usb_get_urb() and usb_put_urb() in an unbalanced way causing
isochronous URB's kref.counts incrementing once per usb_submit_urb() call.
The culprit is *usb being set to NULL when usb_put_urb() is called after URB
is given back.
Due to other fixes there is no need for ehci-hcd to deal with usb_get_urb()
nor usb_put_urb() anymore, so patch removes their usages in ehci-hcd.
Patch also makes ehci_to_hcd(ehci)->self.bandwidth_allocated adjust, if a
stream finishes.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Please consider this small patch for the usb option-card driver.
This patch adds the ZTE 622 usb modem device.
Signed-off-by: Albert Pauw <albert.pauw@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure we don't leak locked vstdev->lock in vstusb_write. Unlock
properly on one fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is an omitted unlock in mdc800_usb_probe's fail path. Add it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Henning Zabel <henning@uni-paderborn.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We do not hold mutex in one place in cxacru_cm, but unlock it on fail path.
Fix this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Simon Arlott <cxacru@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbfs driver manages a list of completed asynchronous URBs. But
it is too eager to free the entries on this list: destroy_async() gets
called whenever an interface is unbound or a device is removed, and it
deallocates the outstanding struct async entries for all URBs on that
interface or device. This is wrong; the user program should be able
to reap an URB any time after it has completed, regardless of whether
or not the interface is still bound or the device is still present.
This patch (as1222) moves the code for deallocating the completed list
entries from destroy_async() to usbdev_release(). The outstanding
entries won't be freed until the user program has closed the device
file, thereby eliminating any possibility that the remaining URBs
might still be reaped.
This fixes a bug in which a program can hang in the USBDEVFS_REAPURB
ioctl when the device is unplugged.
Reported-and-tested-by: Martin Poupe <martin.poupe@upek.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver already supports the 1 protocol support, so just add it to
the MODULE_DEVICE_TABLE entry so it properly picks up these devices.
Thanks to Jouni Rynö for pointing this out.
Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
open() will never succeed, as we always return -ENODEV. Fix this
obvious bug.
Thanks to Jouni Ryno for reporting it.
Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
acpi-wmi: unsigned cannot be less than 0
thinkpad-acpi: fix module autoloading for older models
acer-wmi: Unmark as 'experimental'
acpi-wmi: Unmark as 'experimental'
acer-wmi: double free in acer_rfkill_exit()
platform/x86: depends instead of select for laptop platform drivers
asus-laptop: use select instead of depends on
eeepc-laptop: restore acpi_generate_proc_event()
asus-laptop: restore acpi_generate_proc_event()
acpi: check for pxm_to_node_map overflow
ACPI: remove doubled status checking
ACPI suspend: Blacklist Toshiba Satellite L300 that requires to set SCI_EN directly on resume
Revert "ACPI: make some IO ports off-limits to AML"
suspend: switch the Asus Pundit P1-AH2 to old ACPI sleep ordering
The following oops has been reported when dm-crypt runs over a loop device.
...
[ 70.381058] Process loop0 (pid: 4268, ti=cf3b2000 task=cf1cc1f0 task.ti=cf3b2000)
...
[ 70.381058] Call Trace:
[ 70.381058] [<d0d76601>] ? crypt_dec_pending+0x5e/0x62 [dm_crypt]
[ 70.381058] [<d0d767b8>] ? crypt_endio+0xa2/0xaa [dm_crypt]
[ 70.381058] [<d0d76716>] ? crypt_endio+0x0/0xaa [dm_crypt]
[ 70.381058] [<c01a2f24>] ? bio_endio+0x2b/0x2e
[ 70.381058] [<d0806530>] ? dec_pending+0x224/0x23b [dm_mod]
[ 70.381058] [<d08066e4>] ? clone_endio+0x79/0xa4 [dm_mod]
[ 70.381058] [<d080666b>] ? clone_endio+0x0/0xa4 [dm_mod]
[ 70.381058] [<c01a2f24>] ? bio_endio+0x2b/0x2e
[ 70.381058] [<c02bad86>] ? loop_thread+0x380/0x3b7
[ 70.381058] [<c02ba8a1>] ? do_lo_send_aops+0x0/0x165
[ 70.381058] [<c013754f>] ? autoremove_wake_function+0x0/0x33
[ 70.381058] [<c02baa06>] ? loop_thread+0x0/0x3b7
When a table is being replaced, it waits for I/O to complete
before destroying the mempool, but the endio function doesn't
call mempool_free() until after completing the bio.
Fix it by swapping the order of those two operations.
The same problem occurs in dm.c with md referenced after dec_pending.
Again, we swap the order.
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
In the async encryption-complete function (kcryptd_async_done), the
crypto_async_request passed in may be different from the one passed to
crypto_ablkcipher_encrypt/decrypt. Only crypto_async_request->data is
guaranteed to be same as the one passed in. The current
kcryptd_async_done uses the passed-in crypto_async_request directly
which may cause the AES-NI-based AES algorithm implementation to panic.
This patch fixes this bug by only using crypto_async_request->data,
which points to dm_crypt_request, the crypto_async_request passed in.
The original data (convert_context) is gotten from dm_crypt_request.
[mbroz@redhat.com: reworked]
Cc: stable@kernel.org
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-io calls bio_get_nr_vecs to get the maximum number of pages to use
for a given device. It allocates one additional bio_vec to use
internally but failed to respect BIO_MAX_PAGES, so fix this.
This was the likely cause of:
https://bugzilla.redhat.com/show_bug.cgi?id=173153
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix an error introduced in dm-table-rework-reference-counting.patch.
When there is failure after table initialization, we need to use
dm_table_destroy, not dm_table_put, to free the table.
dm_table_put may be used only after dm_table_get.
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When renaming a mapped device validate the length of the new name.
The rename ioctl accepted any correctly-terminated string enclosed
within the data passed from userspace. The other ioctls enforce a
size limit of DM_NAME_LEN. If the name is changed and becomes longer
than that, the device can no longer be addressed by name.
Fix it by properly checking for device name length (including
terminating zero).
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Impact: help prevent extinction of species
The Tasmanian Devil is a shy iconic Australian creature named for its
spine-chilling screech. It is threatened with extinction due to a
scientifically interesting but horrific transmissible facial cancer.
This one is standing in for Tux for one release using the far less-known
Devil Facial Tux Disguise.
Save The Tasmanian Devil http://tassiedevil.com.au
Signed-off-by: Linux.conf.au Hobart Team <contact@marchsouth.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
include/linux/pci-acpi.h:74:
typedef u32 acpi_status;
result is unsigned, so an error returned by acpi_bus_register_driver()
will not be noticed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Looking at the source, there seems to be a missing * to match my DMI
string. I mean for newer IBM and Lenovo's laptops you match either one
of the following:
MODULE_ALIAS("dmi:bvnIBM:*:svnIBM:*:pvrThinkPad*:rvnIBM:*");
MODULE_ALIAS("dmi:bvnLENOVO:*:svnLENOVO:*:pvrThinkPad*:rvnLENOVO:*");
While for older Thinkpads, you do this (for instance):
IBM_BIOS_MODULE_ALIAS("1[0,3,6,8,A-G,I,K,M-P,S,T]");
with IBM_BIOS_MODULE_ALIAS being MODULE_ALIAS("dmi:bvnIBM:bvr" __type "ET??WW")
Note there's no * terminating the string. As result, udev doesn't load
anything because modprobe cannot find anything matching this (my
machine actually):
udevtest: run: '/sbin/modprobe dmi:bvnIBM:bvr1IET71WW(2.10):bd06/16/2006:svnIBM:pn236621U:pvrNotAv
Signed-off-by: Mathieu Chouquet-Stringer <mchouque@free.fr>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
This driver has been around and used long enough that we can drop the
'experimental'.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI-WMI isn't experimental anymore, and there are other drivers that now
depend on it that aren't either.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
This is acer_rfkill_exit() from drivers/platform/x86/acer-wmi.c.
The code frees wireless_rfkill->data again instead of
bluetooth_rfkill->data.
This was found using a code checker (http://repo.or.cz/w/smatch.git/).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
"I hate `select' and will gleefully leap on any s/select/depends/ patch,
whether it works or not :)"
Andrew Morton
select INPUT is not needed here, because if someone doesn't want INPUT,
he won't want these drivers either.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Like thinkpad_acpi or eeepc-laptop, asus-laptop will
now use "select" instead of "depends on"
for LEDS_CLASS, NEW_LEDS and BACKLIGHT_CLASS_DEVICE
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Restore acpi_generate_proc_event() for backward
compatibility with old acpi scripts.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Restore acpi_generate_proc_event() for backward
compatibility with old acpi scripts.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
It is hardly (if ever) possible but in case of broken _PXM entry we could
reach out of pxm_to_node_map array bounds in acpi_map_pxm_to_node() call.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
