sata_promise's reset code has deviated quite a bit from
the Promise reference driver's, and it has been observed
to fail to recover from errors in some cases.
This patch thus updates the reset code to more closely
match the reference driver:
- soft reset (pdc_reset_port):
* wait for ATA engine to not be in packet command mode
(2nd gen only)
* write reset bit in PDC_CTLSTAT before the first read
in the loop
* for 2nd gen SATA follow up with FPDMA reset and clearing
error status registers
- hard reset (pdc_sata_hardreset):
* wait for ATA engine to not be in packet command mode
(2nd gen only)
* reset ATA engine via the PCI control register
* Tejun's change to use non-waiting hardreset + follow-up SRST
I'm not changing the hotplug mask bits since they are taken care
of by sata_promise's ->freeze() and ->thaw() operations. And I'm
not writing the PMP port # because that's always zero (for now).
Tested here on various controllers. In particular, one disk
which used to timeout and fail to recover from certain hdparm
and smartmonctl commands now works nicely.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
1st generation Promise SATA chips are prone to generating spurious
hotplug events which can disrupt normal operation. This has been
observed on 20376 and 20378 chips. This patch thus disables hotplug
support on 1st gen chips while leaving it enabled for 2nd gen chips.
The pdc_sata_hotplug_offset() function becomes redundant so it is
removed.
Tested on 1st gen 20376 and 20378 mainboard chips and on a 2nd gen
SATA300 PCI card.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Kurt Roeckx <kurt@roeckx.be>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 54c38444fa makes libata abort qcs
after the port is frozen. This is necessary to guarantee that TF
registers are accessed after the DMA engine is shutdown after an
error. However, this triggers WARN_ON_ONCE() check in
ata_qc_complete() spuriously. Move WARN_ON_ONCE() downwards such that
failing commands while frozen doesn't trigger it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit a5bfc4714b dropped explicit
pci_intx() manipulation from ahci because it seemed unnecessary and
ahci doesn't seem to be the right place to be tweaking it if it were.
This was largely okay but there are exceptions. There was one on an
embedded platform which was fixed via firmware and now bko#14124
reports it on a HP DL320.
http://bugzilla.kernel.org/show_bug.cgi?id=14124
I still think this isn't something libata drivers should be caring
about (the only ones which are calling pci_intx() explicitly are
libata ones and one other driver) but for now reverting the change
seems to be the right thing to do.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch refines ahci_kick_engine() after discussion with Tejun about
FBS(FIS-based switching) support preparation:
a. Kill @force_restart and always kick the engine. The only case where
@force_restart is zero is when it's called from ahci_p5wdh_hardreset()
Actually at that point, BSY is pretty much guaranteed to be set.
b. If PMP is attached, ignore busy and always do CLO. (AHCI-1.3 9.2)
Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix for non-ncq & ncq commands causing timeouts when both are issued
simultaneously to the same device.
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
[fixed to be actual compileable C code -jg]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This small patch is just adding the information for PMP spec 1.2
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_tf_read_block() has off-by-one error when converting CHS address
to LBA. The bug isn't very visible because ata_tf_read_block() is
used only when generating sense data for a failed RW command and CHS
addressing isn't used too often these days.
This problem was spotted by Atsushi Nemoto.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It turns out ASUS M2A-VM isn't the only one with the 32bit DMA
problem. Make ahci_asus_m2a_vm_32bit_only() more generic using the
new dmi_get_date() and rename it to ahci_sb600_32bit_only(). Cut off
date is now pointed to by dmi_system_id->driver_data in "yyyymmdd"
format and it's now also allowed to be omitted.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sandor Bodo-Merle <sbodomerle@gmail.com>
Cc: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are cases where full date information is required instead of
just the year. Add month and day parsing to dmi_get_year() and rename
it to dmi_get_date().
As the original function only required '/' followed by any number of
parseable characters at the end of the string, keep that behavior to
avoid upsetting existing users.
The new function takes dates of format [mm[/dd]]/yy[yy]. Year, month
and date are checked to be in the ranges of [1-9999], [1-12] and
[1-31] respectively and any invalid or out-of-range component is
returned as zero.
The dummy implementation is updated accordingly but the return value
is updated to indicate field not found which is consistent with how
other dummy functions behave.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_scsi_pass_thru() was checking for input sanity and disallowed
commands while initializaing qc from scmd. TPM filtering was added
right after protocol check at which point tf wasn't initialized
properly. This means that TPM filtering has never really worked.
This patch fixes the bug by reorganizing ata_scsi_pass_thru() such
that qc is fully initialized before checking for invalid conditions
which is way less error prone.
Discovered while Thilo-Alexander Ginkel was trying debug patches for
bko#13416.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Thilo-Alexander Ginkel <thilo@ginkel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During introduction of slave_link, sata_sis slipped through the crack
and left with ad-hoc merged SCR access. As SCR status was shared for
both the master and slave devices, when only one of the device is
online, libata EH would think both are online but would only get valid
device signature for the actually present one, which in turn trigger
the probing safety net mechanism and make EH retry causing large delay
during boot. This patch converts sata_sis to slave_link mechanism.
This bug was reported by TAXI in bko#14075.
http://bugzilla.kernel.org/show_bug.cgi?id=14075
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: TAXI <taxi@a-city.de>
Cc: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The sil24 hardware has a built-in list of commands and associated protocols
that gets used by default to decide how to handle a given command. However,
if the command is not known to the controller then it presumably assumes it to
be a non-data command which then causes protocol mismatch errors if the device
ends up requesting data transfer. The new DATA SET MANAGEMENT - Trim command
causes this issue since it's a DMA data-out command.
Since we should always know best what protocol the command should be using,
let's just set the override flag to inform the controller what protocol to use
for all non-ATAPI commands with data transfer.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Tested-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
AHCI exports various capability bits that may be of interest to userspace
such as whether the BIOS claims a port is hotpluggable or eSATA. Providing
these via sysfs along with the version of the AHCI spec implemented by
the host allows userspace to make policy decisions for things like ALPM.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that the SCSI disk driver correctly handles non-rotational devices
we can move setting the queue flag to SCSI.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was a hack to give userland shutdown tools time to drop manual
spindown. All popular distros updated quite some time ago and the due
is well passed. Drop it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch improve libata's output for error/notification messages
to allow easier comprehension and debugging:
When ATAPI commands issued through the SCSI layer fail, use SCSI
functions to print the CDB in human-readable form instead of just
dumping out the CDB in hex.
Print out the name of the failed command (as defined by the ATA
specification) in error handling output along with the raw register
contents.
When reporting status of ACPI taskfile commands executed on resume,
also output the names of the commands being executed (or not) in
readable form.
Since the extra data for printing command names increases kernel
size slightly, a config option has been added to allow disabling
command name output (as well as some of the error register parsing)
for those highly sensitive to kernel text size.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Resets are done with port frozen but some controllers still issue
interrupts during reset and they may end up recording error conditions
in ehi leading to unnecessary EH retrials.
This patch makes ata_eh_reset() clear ehi on reset completion. As
reset is the most severe recovery action, there's nothing to lose by
clearing ehi on its completion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Zdenek Kaspar <zkaspar82@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hopefully results in fewer on-the-wire FIS's and no breakage. We'll see!
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Call the ->freeze() hook before aborting qc's, because some hardware
requires special handling prior to accessing the taskfile registers
(for diagnosis/analysis/reset). Most notably, hardware may wish to
disable the DMA engine or interrupts in the ->freeze() hook.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit log for commit 517d3cc15b
("[libata] ata_piix: Enable parallel scan") says:
This patch turns on parallel scanning for the ata_piix driver.
This driver is used on most netbooks (no AHCI for cheap storage it seems).
The scan is the dominating time factor in the kernel boot for these
devices; with this flag it gets cut in half for the device I used
for testing (eeepc).
Alan took a look at the driver source and concluded that it ought to be safe
to do for this driver. Alan has also checked with the hardware team.
and it is all true but once we put all things together additional
constraints for PATA controllers show up (some hardware registers
have per-host not per-port atomicity) and we risk misprogramming
the controller.
I used the following test to check whether the issue is real:
@@ -736,8 +736,20 @@ static void piix_set_piomode(struct ata_
(timings[pio][1] << 8);
}
pci_write_config_word(dev, master_port, master_data);
- if (is_slave)
+ if (is_slave) {
+ if (ap->port_no == 0) {
+ u8 tmp = slave_data;
+
+ while (slave_data == tmp) {
+ pci_read_config_byte(dev, slave_port, &tmp);
+ msleep(50);
+ }
+
+ dev_printk(KERN_ERR, &dev->dev, "PATA parallel scan "
+ "race detected\n");
+ }
pci_write_config_byte(dev, slave_port, slave_data);
+ }
/* Ensure the UDMA bit is off - it will be turned back on if
UDMA is selected */
and it indeed triggered the error message.
Lets fix all such races by adding an extra locking to ->set_piomode
and ->set_dmamode methods for PATA controllers.
[ Alan: would be better to take the host lock in libata-core for these
cases so that we fix all the adapters in one swoop. "Looks fine as a
temproary quickfix tho" ]
Cc: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some gigabytes have on-board SIMG5723s connected to JMB ahcis. These
are used to implement hardware raid. Unfortunately some firmware
revisions on these 5723s don't bring the link down when all the
downstream ports are unoccupied while not responding to reset protocol
which makes libata think that there's device attached to the port but
is not responding and retry. This results in painfully wrong boot
detection time for these ports when they're empty.
This patch quirks those boards such that ahci gives up after the
initial timeout. Combined with parallel probing, this gives quick
enough probing and also is safe because SIMG5723 will respond to the
first try if any of the downstream ports is occupied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marc Bowes <marcbowes@gmail.com>
Reported-by: Nicolas Mailhot <Nicolas.Mailhot@LaPoste.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Too strong words led to spurious bug reports: Novell bugzilla #527748,
RedHat bugzilla #468800. This patch is used to soften up the dmesg on
SB600 PMP softreset failure recovery, so as to remove the scariness and
concern from community.
Reported-by: pgnet Dev <pgnet.dev@gmail.com>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
At least the nVidia MCP55 controller quite happily supports MSI.
This adds an option to use it. It is disabled by default.
As per feedback by Robert Hancock, it will honour the user
request as the kernel will not enable MSI where the controller
or the specific system configuration do not support it.
Signed-off-by: Tony Vroon <tony@linx.net>
Cc: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
OCZ Vertex SSD can't do HPA and not in a usual way. It reports HPA,
allows unlocking but then fails all IOs which fall in the unlocked
area. Quirk it so that HPA unlocking is not used for the device.
Reported by Daniel Perup in bnc#522414.
https://bugzilla.novell.com/show_bug.cgi?id=522414
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Daniel Perup <probe@spray.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PIO and MWDMA timings are never programmed for the second channel
because timing registers are treated as 16-bit long ones.
The bug is an attixp -> pata_atiixp regression and goes back to:
commit 669a5db411
Author: Jeff Garzik <jeff@garzik.org>
Date: Tue Aug 29 18:12:40 2006 -0400
[libata] Add a bunch of PATA drivers.
Cc: Krystian Juskowiak <jusko@tlen.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Julias Lawall discovered that pata_at91 wasn't freeing a memory region
allocated with kzalloc() on init failure paths. Upon review,
pata_at91 also seems to be doing unnecessary explicit resource
releases for managed resources too. Convert memory allocation to
managed one and drop unnecessary explicit resource releases.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Julia Lawall <julia@diku.dk>
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On certain configurations, HPA isn't or can't be unlocked during
probing but it somehow ends up unlocked afterwards. In the following
thread, the problem can be reliably reproduced after resuming from
STR. The BIOS turns on HPA during boot but forgets to do it during
resume.
http://thread.gmane.org/gmane.linux.kernel/858310
This patch updates libata revalidation such that it considers native
n_sectors. If the device size has increased to match native
n_sectors, it's assumed that HPA has been unlocked involuntarily and
the device is recognized as the same one. This should be fairly safe
while nicely working around the problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christof Warlich <christof@warlich.name>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Please consider the following updates and fixes for pata_at91 driver.
* Removed extra headers
Here we need only static memory controller properties, which are
contained in generic header at91sam9_smc.h.
No need to include any specific headers for at91sam9260 SoC.
* No harsh BUG_ON for get_clk in set_smc_timing function
get_clk is now performed in driver probing function,
probing fails if master clock is not available
* Fixed uint/ulong mess in calc_mck_cycles function
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
OriginalAuthor: Michael Frey <michael.frey@canonical.com>
Signed-off-by: Steve Conklin <sconklin@canonical.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add device IDS for Ibex Peak SATA AHCI Controllers
Signed-off-by: Jaroslav Kysela <jkysela@redhat.com>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
host->ports[] always contain pointers to valid port structures since
a "dummy port" structure is used in case if there is no physical port.
This patch takes care of two entries from Dan's list:
drivers/ata/sata_sil.c +535 sil_interrupt(13) warning: variable derefenced before check 'ap'
drivers/ata/sata_mv.c +2517 mv_unexpected_intr(6) warning: variable derefenced before check 'ap'
and of another needless NULL pointer check in pata_octeon_cf.c.
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: corbet@lwn.net
Cc: eteo@redhat.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/libata-eh.c +2403 ata_eh_reset(80) warning: variable derefenced before check 'slave'
Please note that this is _not_ a real bug at the moment since ata_eh_context
structure is embedded into ata_list structure and the code alwas checks for
'slave' before accessing 'sehc'.
Anyway lets add missing check and always have a valid 'sehc' pointer (which
makes code easier to understand and prevents introducing some possible bugs
in the future).
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: corbet@lwn.net
Cc: eteo@redhat.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add device ID for Intel 82801JI SATA AHCI controller.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If the NULL test is necessary, then the dereference should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PIONEER DVD-RW DVRTD08 times out SETXFER if no media is present. The
device is SATA and simply skipping SETXFER works around the problem.
Implement ATA_HORKAGE_NOSETXFER and apply it to the device.
Reported by Moritz Rigler in the following thread.
http://thread.gmane.org/gmane.linux.ide/36790
and by Lars in bko#9540.
Updated to whine and ignore NOSETXFER if PATA component is detected as
suggested by Alan Cox.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Moritz Rigler <linux-ide@momail.e4ward.com>
Reported-by: Lars <lars21ce@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_eh_reset() was missing error return handling after follow-up SRST
allowing EH to continue the normal probing path after reset failure.
This was discovered while testing new WD 2TB drives which take longer
than 10 secs to spin up and cause the first follow-up SRST to time
out.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Before issuing reset, libata configures xfermode to PIO0 which makes
some drivers turn on IORDY which may cause the controller to lock up
if the port is not occupied. IORDY isn't necessary at this point
anyway. Make ata_pio_need_iordy() return zero if it's being called
for reset.
This fixes bko#11703. Reported and tracked down by Daniel Gnoutcheff
and Constantine Gavrilov.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Daniel Gnoutcheff <gnoutchd@union.edu>
Cc: Constantine Gavrilov <constantine.gavrilov@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch provides PATA driver for CompactFlash interface in True IDE
mode on AT91SAM9260 SoC.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
