mirror of
https://github.com/FEX-Emu/linux.git
synced 2024-12-27 03:47:43 +00:00
284a940675
During boot we bring up all memory and cpu nodes. Normally a PCI device will be in one of these online nodes, however in some weird setups it may not. We have only seen this in the lab but we may as well check for the case and fallback to -1 (all nodes). Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
1428 lines
36 KiB
C
1428 lines
36 KiB
C
/*
|
|
* Port for PPC64 David Engebretsen, IBM Corp.
|
|
* Contains common pci routines for ppc64 platform, pSeries and iSeries brands.
|
|
*
|
|
* Copyright (C) 2003 Anton Blanchard <anton@au.ibm.com>, IBM
|
|
* Rework, based on alpha PCI code.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* as published by the Free Software Foundation; either version
|
|
* 2 of the License, or (at your option) any later version.
|
|
*/
|
|
|
|
#undef DEBUG
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/string.h>
|
|
#include <linux/init.h>
|
|
#include <linux/bootmem.h>
|
|
#include <linux/mm.h>
|
|
#include <linux/list.h>
|
|
#include <linux/syscalls.h>
|
|
#include <linux/irq.h>
|
|
|
|
#include <asm/processor.h>
|
|
#include <asm/io.h>
|
|
#include <asm/prom.h>
|
|
#include <asm/pci-bridge.h>
|
|
#include <asm/byteorder.h>
|
|
#include <asm/machdep.h>
|
|
#include <asm/ppc-pci.h>
|
|
#include <asm/firmware.h>
|
|
|
|
#ifdef DEBUG
|
|
#include <asm/udbg.h>
|
|
#define DBG(fmt...) printk(fmt)
|
|
#else
|
|
#define DBG(fmt...)
|
|
#endif
|
|
|
|
unsigned long pci_probe_only = 1;
|
|
int pci_assign_all_buses = 0;
|
|
|
|
#ifdef CONFIG_PPC_MULTIPLATFORM
|
|
static void fixup_resource(struct resource *res, struct pci_dev *dev);
|
|
static void do_bus_setup(struct pci_bus *bus);
|
|
static void phbs_remap_io(void);
|
|
#endif
|
|
|
|
/* pci_io_base -- the base address from which io bars are offsets.
|
|
* This is the lowest I/O base address (so bar values are always positive),
|
|
* and it *must* be the start of ISA space if an ISA bus exists because
|
|
* ISA drivers use hard coded offsets. If no ISA bus exists a dummy
|
|
* page is mapped and isa_io_limit prevents access to it.
|
|
*/
|
|
unsigned long isa_io_base; /* NULL if no ISA bus */
|
|
EXPORT_SYMBOL(isa_io_base);
|
|
unsigned long pci_io_base;
|
|
EXPORT_SYMBOL(pci_io_base);
|
|
|
|
void iSeries_pcibios_init(void);
|
|
|
|
LIST_HEAD(hose_list);
|
|
|
|
struct dma_mapping_ops pci_dma_ops;
|
|
EXPORT_SYMBOL(pci_dma_ops);
|
|
|
|
int global_phb_number; /* Global phb counter */
|
|
|
|
/* Cached ISA bridge dev. */
|
|
struct pci_dev *ppc64_isabridge_dev = NULL;
|
|
EXPORT_SYMBOL_GPL(ppc64_isabridge_dev);
|
|
|
|
static void fixup_broken_pcnet32(struct pci_dev* dev)
|
|
{
|
|
if ((dev->class>>8 == PCI_CLASS_NETWORK_ETHERNET)) {
|
|
dev->vendor = PCI_VENDOR_ID_AMD;
|
|
pci_write_config_word(dev, PCI_VENDOR_ID, PCI_VENDOR_ID_AMD);
|
|
}
|
|
}
|
|
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TRIDENT, PCI_ANY_ID, fixup_broken_pcnet32);
|
|
|
|
void pcibios_resource_to_bus(struct pci_dev *dev, struct pci_bus_region *region,
|
|
struct resource *res)
|
|
{
|
|
unsigned long offset = 0;
|
|
struct pci_controller *hose = pci_bus_to_host(dev->bus);
|
|
|
|
if (!hose)
|
|
return;
|
|
|
|
if (res->flags & IORESOURCE_IO)
|
|
offset = (unsigned long)hose->io_base_virt - pci_io_base;
|
|
|
|
if (res->flags & IORESOURCE_MEM)
|
|
offset = hose->pci_mem_offset;
|
|
|
|
region->start = res->start - offset;
|
|
region->end = res->end - offset;
|
|
}
|
|
|
|
void pcibios_bus_to_resource(struct pci_dev *dev, struct resource *res,
|
|
struct pci_bus_region *region)
|
|
{
|
|
unsigned long offset = 0;
|
|
struct pci_controller *hose = pci_bus_to_host(dev->bus);
|
|
|
|
if (!hose)
|
|
return;
|
|
|
|
if (res->flags & IORESOURCE_IO)
|
|
offset = (unsigned long)hose->io_base_virt - pci_io_base;
|
|
|
|
if (res->flags & IORESOURCE_MEM)
|
|
offset = hose->pci_mem_offset;
|
|
|
|
res->start = region->start + offset;
|
|
res->end = region->end + offset;
|
|
}
|
|
|
|
#ifdef CONFIG_HOTPLUG
|
|
EXPORT_SYMBOL(pcibios_resource_to_bus);
|
|
EXPORT_SYMBOL(pcibios_bus_to_resource);
|
|
#endif
|
|
|
|
/*
|
|
* We need to avoid collisions with `mirrored' VGA ports
|
|
* and other strange ISA hardware, so we always want the
|
|
* addresses to be allocated in the 0x000-0x0ff region
|
|
* modulo 0x400.
|
|
*
|
|
* Why? Because some silly external IO cards only decode
|
|
* the low 10 bits of the IO address. The 0x00-0xff region
|
|
* is reserved for motherboard devices that decode all 16
|
|
* bits, so it's ok to allocate at, say, 0x2800-0x28ff,
|
|
* but we want to try to avoid allocating at 0x2900-0x2bff
|
|
* which might have be mirrored at 0x0100-0x03ff..
|
|
*/
|
|
void pcibios_align_resource(void *data, struct resource *res,
|
|
resource_size_t size, resource_size_t align)
|
|
{
|
|
struct pci_dev *dev = data;
|
|
struct pci_controller *hose = pci_bus_to_host(dev->bus);
|
|
resource_size_t start = res->start;
|
|
unsigned long alignto;
|
|
|
|
if (res->flags & IORESOURCE_IO) {
|
|
unsigned long offset = (unsigned long)hose->io_base_virt -
|
|
pci_io_base;
|
|
/* Make sure we start at our min on all hoses */
|
|
if (start - offset < PCIBIOS_MIN_IO)
|
|
start = PCIBIOS_MIN_IO + offset;
|
|
|
|
/*
|
|
* Put everything into 0x00-0xff region modulo 0x400
|
|
*/
|
|
if (start & 0x300)
|
|
start = (start + 0x3ff) & ~0x3ff;
|
|
|
|
} else if (res->flags & IORESOURCE_MEM) {
|
|
/* Make sure we start at our min on all hoses */
|
|
if (start - hose->pci_mem_offset < PCIBIOS_MIN_MEM)
|
|
start = PCIBIOS_MIN_MEM + hose->pci_mem_offset;
|
|
|
|
/* Align to multiple of size of minimum base. */
|
|
alignto = max(0x1000UL, align);
|
|
start = ALIGN(start, alignto);
|
|
}
|
|
|
|
res->start = start;
|
|
}
|
|
|
|
static DEFINE_SPINLOCK(hose_spinlock);
|
|
|
|
/*
|
|
* pci_controller(phb) initialized common variables.
|
|
*/
|
|
static void __devinit pci_setup_pci_controller(struct pci_controller *hose)
|
|
{
|
|
memset(hose, 0, sizeof(struct pci_controller));
|
|
|
|
spin_lock(&hose_spinlock);
|
|
hose->global_number = global_phb_number++;
|
|
list_add_tail(&hose->list_node, &hose_list);
|
|
spin_unlock(&hose_spinlock);
|
|
}
|
|
|
|
struct pci_controller * pcibios_alloc_controller(struct device_node *dev)
|
|
{
|
|
struct pci_controller *phb;
|
|
|
|
if (mem_init_done)
|
|
phb = kmalloc(sizeof(struct pci_controller), GFP_KERNEL);
|
|
else
|
|
phb = alloc_bootmem(sizeof (struct pci_controller));
|
|
if (phb == NULL)
|
|
return NULL;
|
|
pci_setup_pci_controller(phb);
|
|
phb->arch_data = dev;
|
|
phb->is_dynamic = mem_init_done;
|
|
if (dev) {
|
|
int nid = of_node_to_nid(dev);
|
|
|
|
if (nid < 0 || !node_online(nid))
|
|
nid = -1;
|
|
|
|
PHB_SET_NODE(phb, nid);
|
|
}
|
|
return phb;
|
|
}
|
|
|
|
void pcibios_free_controller(struct pci_controller *phb)
|
|
{
|
|
if (phb->is_dynamic)
|
|
kfree(phb);
|
|
}
|
|
|
|
void __devinit pcibios_claim_one_bus(struct pci_bus *b)
|
|
{
|
|
struct pci_dev *dev;
|
|
struct pci_bus *child_bus;
|
|
|
|
list_for_each_entry(dev, &b->devices, bus_list) {
|
|
int i;
|
|
|
|
for (i = 0; i < PCI_NUM_RESOURCES; i++) {
|
|
struct resource *r = &dev->resource[i];
|
|
|
|
if (r->parent || !r->start || !r->flags)
|
|
continue;
|
|
pci_claim_resource(dev, i);
|
|
}
|
|
}
|
|
|
|
list_for_each_entry(child_bus, &b->children, node)
|
|
pcibios_claim_one_bus(child_bus);
|
|
}
|
|
#ifdef CONFIG_HOTPLUG
|
|
EXPORT_SYMBOL_GPL(pcibios_claim_one_bus);
|
|
#endif
|
|
|
|
static void __init pcibios_claim_of_setup(void)
|
|
{
|
|
struct pci_bus *b;
|
|
|
|
if (firmware_has_feature(FW_FEATURE_ISERIES))
|
|
return;
|
|
|
|
list_for_each_entry(b, &pci_root_buses, node)
|
|
pcibios_claim_one_bus(b);
|
|
}
|
|
|
|
#ifdef CONFIG_PPC_MULTIPLATFORM
|
|
static u32 get_int_prop(struct device_node *np, const char *name, u32 def)
|
|
{
|
|
const u32 *prop;
|
|
int len;
|
|
|
|
prop = get_property(np, name, &len);
|
|
if (prop && len >= 4)
|
|
return *prop;
|
|
return def;
|
|
}
|
|
|
|
static unsigned int pci_parse_of_flags(u32 addr0)
|
|
{
|
|
unsigned int flags = 0;
|
|
|
|
if (addr0 & 0x02000000) {
|
|
flags = IORESOURCE_MEM | PCI_BASE_ADDRESS_SPACE_MEMORY;
|
|
flags |= (addr0 >> 22) & PCI_BASE_ADDRESS_MEM_TYPE_64;
|
|
flags |= (addr0 >> 28) & PCI_BASE_ADDRESS_MEM_TYPE_1M;
|
|
if (addr0 & 0x40000000)
|
|
flags |= IORESOURCE_PREFETCH
|
|
| PCI_BASE_ADDRESS_MEM_PREFETCH;
|
|
} else if (addr0 & 0x01000000)
|
|
flags = IORESOURCE_IO | PCI_BASE_ADDRESS_SPACE_IO;
|
|
return flags;
|
|
}
|
|
|
|
#define GET_64BIT(prop, i) ((((u64) (prop)[(i)]) << 32) | (prop)[(i)+1])
|
|
|
|
static void pci_parse_of_addrs(struct device_node *node, struct pci_dev *dev)
|
|
{
|
|
u64 base, size;
|
|
unsigned int flags;
|
|
struct resource *res;
|
|
const u32 *addrs;
|
|
u32 i;
|
|
int proplen;
|
|
|
|
addrs = get_property(node, "assigned-addresses", &proplen);
|
|
if (!addrs)
|
|
return;
|
|
DBG(" parse addresses (%d bytes) @ %p\n", proplen, addrs);
|
|
for (; proplen >= 20; proplen -= 20, addrs += 5) {
|
|
flags = pci_parse_of_flags(addrs[0]);
|
|
if (!flags)
|
|
continue;
|
|
base = GET_64BIT(addrs, 1);
|
|
size = GET_64BIT(addrs, 3);
|
|
if (!size)
|
|
continue;
|
|
i = addrs[0] & 0xff;
|
|
DBG(" base: %llx, size: %llx, i: %x\n",
|
|
(unsigned long long)base, (unsigned long long)size, i);
|
|
|
|
if (PCI_BASE_ADDRESS_0 <= i && i <= PCI_BASE_ADDRESS_5) {
|
|
res = &dev->resource[(i - PCI_BASE_ADDRESS_0) >> 2];
|
|
} else if (i == dev->rom_base_reg) {
|
|
res = &dev->resource[PCI_ROM_RESOURCE];
|
|
flags |= IORESOURCE_READONLY | IORESOURCE_CACHEABLE;
|
|
} else {
|
|
printk(KERN_ERR "PCI: bad cfg reg num 0x%x\n", i);
|
|
continue;
|
|
}
|
|
res->start = base;
|
|
res->end = base + size - 1;
|
|
res->flags = flags;
|
|
res->name = pci_name(dev);
|
|
fixup_resource(res, dev);
|
|
}
|
|
}
|
|
|
|
struct pci_dev *of_create_pci_dev(struct device_node *node,
|
|
struct pci_bus *bus, int devfn)
|
|
{
|
|
struct pci_dev *dev;
|
|
const char *type;
|
|
|
|
dev = kmalloc(sizeof(struct pci_dev), GFP_KERNEL);
|
|
if (!dev)
|
|
return NULL;
|
|
type = get_property(node, "device_type", NULL);
|
|
if (type == NULL)
|
|
type = "";
|
|
|
|
DBG(" create device, devfn: %x, type: %s\n", devfn, type);
|
|
|
|
memset(dev, 0, sizeof(struct pci_dev));
|
|
dev->bus = bus;
|
|
dev->sysdata = node;
|
|
dev->dev.parent = bus->bridge;
|
|
dev->dev.bus = &pci_bus_type;
|
|
dev->devfn = devfn;
|
|
dev->multifunction = 0; /* maybe a lie? */
|
|
|
|
dev->vendor = get_int_prop(node, "vendor-id", 0xffff);
|
|
dev->device = get_int_prop(node, "device-id", 0xffff);
|
|
dev->subsystem_vendor = get_int_prop(node, "subsystem-vendor-id", 0);
|
|
dev->subsystem_device = get_int_prop(node, "subsystem-id", 0);
|
|
|
|
dev->cfg_size = pci_cfg_space_size(dev);
|
|
|
|
sprintf(pci_name(dev), "%04x:%02x:%02x.%d", pci_domain_nr(bus),
|
|
dev->bus->number, PCI_SLOT(devfn), PCI_FUNC(devfn));
|
|
dev->class = get_int_prop(node, "class-code", 0);
|
|
|
|
DBG(" class: 0x%x\n", dev->class);
|
|
|
|
dev->current_state = 4; /* unknown power state */
|
|
|
|
if (!strcmp(type, "pci") || !strcmp(type, "pciex")) {
|
|
/* a PCI-PCI bridge */
|
|
dev->hdr_type = PCI_HEADER_TYPE_BRIDGE;
|
|
dev->rom_base_reg = PCI_ROM_ADDRESS1;
|
|
} else if (!strcmp(type, "cardbus")) {
|
|
dev->hdr_type = PCI_HEADER_TYPE_CARDBUS;
|
|
} else {
|
|
dev->hdr_type = PCI_HEADER_TYPE_NORMAL;
|
|
dev->rom_base_reg = PCI_ROM_ADDRESS;
|
|
/* Maybe do a default OF mapping here */
|
|
dev->irq = NO_IRQ;
|
|
}
|
|
|
|
pci_parse_of_addrs(node, dev);
|
|
|
|
DBG(" adding to system ...\n");
|
|
|
|
pci_device_add(dev, bus);
|
|
|
|
/* XXX pci_scan_msi_device(dev); */
|
|
|
|
return dev;
|
|
}
|
|
EXPORT_SYMBOL(of_create_pci_dev);
|
|
|
|
void __devinit of_scan_bus(struct device_node *node,
|
|
struct pci_bus *bus)
|
|
{
|
|
struct device_node *child = NULL;
|
|
const u32 *reg;
|
|
int reglen, devfn;
|
|
struct pci_dev *dev;
|
|
|
|
DBG("of_scan_bus(%s) bus no %d... \n", node->full_name, bus->number);
|
|
|
|
while ((child = of_get_next_child(node, child)) != NULL) {
|
|
DBG(" * %s\n", child->full_name);
|
|
reg = get_property(child, "reg", ®len);
|
|
if (reg == NULL || reglen < 20)
|
|
continue;
|
|
devfn = (reg[0] >> 8) & 0xff;
|
|
|
|
/* create a new pci_dev for this device */
|
|
dev = of_create_pci_dev(child, bus, devfn);
|
|
if (!dev)
|
|
continue;
|
|
DBG("dev header type: %x\n", dev->hdr_type);
|
|
|
|
if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE ||
|
|
dev->hdr_type == PCI_HEADER_TYPE_CARDBUS)
|
|
of_scan_pci_bridge(child, dev);
|
|
}
|
|
|
|
do_bus_setup(bus);
|
|
}
|
|
EXPORT_SYMBOL(of_scan_bus);
|
|
|
|
void __devinit of_scan_pci_bridge(struct device_node *node,
|
|
struct pci_dev *dev)
|
|
{
|
|
struct pci_bus *bus;
|
|
const u32 *busrange, *ranges;
|
|
int len, i, mode;
|
|
struct resource *res;
|
|
unsigned int flags;
|
|
u64 size;
|
|
|
|
DBG("of_scan_pci_bridge(%s)\n", node->full_name);
|
|
|
|
/* parse bus-range property */
|
|
busrange = get_property(node, "bus-range", &len);
|
|
if (busrange == NULL || len != 8) {
|
|
printk(KERN_DEBUG "Can't get bus-range for PCI-PCI bridge %s\n",
|
|
node->full_name);
|
|
return;
|
|
}
|
|
ranges = get_property(node, "ranges", &len);
|
|
if (ranges == NULL) {
|
|
printk(KERN_DEBUG "Can't get ranges for PCI-PCI bridge %s\n",
|
|
node->full_name);
|
|
return;
|
|
}
|
|
|
|
bus = pci_add_new_bus(dev->bus, dev, busrange[0]);
|
|
if (!bus) {
|
|
printk(KERN_ERR "Failed to create pci bus for %s\n",
|
|
node->full_name);
|
|
return;
|
|
}
|
|
|
|
bus->primary = dev->bus->number;
|
|
bus->subordinate = busrange[1];
|
|
bus->bridge_ctl = 0;
|
|
bus->sysdata = node;
|
|
|
|
/* parse ranges property */
|
|
/* PCI #address-cells == 3 and #size-cells == 2 always */
|
|
res = &dev->resource[PCI_BRIDGE_RESOURCES];
|
|
for (i = 0; i < PCI_NUM_RESOURCES - PCI_BRIDGE_RESOURCES; ++i) {
|
|
res->flags = 0;
|
|
bus->resource[i] = res;
|
|
++res;
|
|
}
|
|
i = 1;
|
|
for (; len >= 32; len -= 32, ranges += 8) {
|
|
flags = pci_parse_of_flags(ranges[0]);
|
|
size = GET_64BIT(ranges, 6);
|
|
if (flags == 0 || size == 0)
|
|
continue;
|
|
if (flags & IORESOURCE_IO) {
|
|
res = bus->resource[0];
|
|
if (res->flags) {
|
|
printk(KERN_ERR "PCI: ignoring extra I/O range"
|
|
" for bridge %s\n", node->full_name);
|
|
continue;
|
|
}
|
|
} else {
|
|
if (i >= PCI_NUM_RESOURCES - PCI_BRIDGE_RESOURCES) {
|
|
printk(KERN_ERR "PCI: too many memory ranges"
|
|
" for bridge %s\n", node->full_name);
|
|
continue;
|
|
}
|
|
res = bus->resource[i];
|
|
++i;
|
|
}
|
|
res->start = GET_64BIT(ranges, 1);
|
|
res->end = res->start + size - 1;
|
|
res->flags = flags;
|
|
fixup_resource(res, dev);
|
|
}
|
|
sprintf(bus->name, "PCI Bus %04x:%02x", pci_domain_nr(bus),
|
|
bus->number);
|
|
DBG(" bus name: %s\n", bus->name);
|
|
|
|
mode = PCI_PROBE_NORMAL;
|
|
if (ppc_md.pci_probe_mode)
|
|
mode = ppc_md.pci_probe_mode(bus);
|
|
DBG(" probe mode: %d\n", mode);
|
|
|
|
if (mode == PCI_PROBE_DEVTREE)
|
|
of_scan_bus(node, bus);
|
|
else if (mode == PCI_PROBE_NORMAL)
|
|
pci_scan_child_bus(bus);
|
|
}
|
|
EXPORT_SYMBOL(of_scan_pci_bridge);
|
|
#endif /* CONFIG_PPC_MULTIPLATFORM */
|
|
|
|
void __devinit scan_phb(struct pci_controller *hose)
|
|
{
|
|
struct pci_bus *bus;
|
|
struct device_node *node = hose->arch_data;
|
|
int i, mode;
|
|
struct resource *res;
|
|
|
|
DBG("Scanning PHB %s\n", node ? node->full_name : "<NO NAME>");
|
|
|
|
bus = pci_create_bus(NULL, hose->first_busno, hose->ops, node);
|
|
if (bus == NULL) {
|
|
printk(KERN_ERR "Failed to create bus for PCI domain %04x\n",
|
|
hose->global_number);
|
|
return;
|
|
}
|
|
bus->secondary = hose->first_busno;
|
|
hose->bus = bus;
|
|
|
|
bus->resource[0] = res = &hose->io_resource;
|
|
if (res->flags && request_resource(&ioport_resource, res))
|
|
printk(KERN_ERR "Failed to request PCI IO region "
|
|
"on PCI domain %04x\n", hose->global_number);
|
|
|
|
for (i = 0; i < 3; ++i) {
|
|
res = &hose->mem_resources[i];
|
|
bus->resource[i+1] = res;
|
|
if (res->flags && request_resource(&iomem_resource, res))
|
|
printk(KERN_ERR "Failed to request PCI memory region "
|
|
"on PCI domain %04x\n", hose->global_number);
|
|
}
|
|
|
|
mode = PCI_PROBE_NORMAL;
|
|
#ifdef CONFIG_PPC_MULTIPLATFORM
|
|
if (node && ppc_md.pci_probe_mode)
|
|
mode = ppc_md.pci_probe_mode(bus);
|
|
DBG(" probe mode: %d\n", mode);
|
|
if (mode == PCI_PROBE_DEVTREE) {
|
|
bus->subordinate = hose->last_busno;
|
|
of_scan_bus(node, bus);
|
|
}
|
|
#endif /* CONFIG_PPC_MULTIPLATFORM */
|
|
if (mode == PCI_PROBE_NORMAL)
|
|
hose->last_busno = bus->subordinate = pci_scan_child_bus(bus);
|
|
}
|
|
|
|
static int __init pcibios_init(void)
|
|
{
|
|
struct pci_controller *hose, *tmp;
|
|
|
|
/* For now, override phys_mem_access_prot. If we need it,
|
|
* later, we may move that initialization to each ppc_md
|
|
*/
|
|
ppc_md.phys_mem_access_prot = pci_phys_mem_access_prot;
|
|
|
|
if (firmware_has_feature(FW_FEATURE_ISERIES))
|
|
iSeries_pcibios_init();
|
|
|
|
printk(KERN_DEBUG "PCI: Probing PCI hardware\n");
|
|
|
|
/* Scan all of the recorded PCI controllers. */
|
|
list_for_each_entry_safe(hose, tmp, &hose_list, list_node) {
|
|
scan_phb(hose);
|
|
pci_bus_add_devices(hose->bus);
|
|
}
|
|
|
|
if (!firmware_has_feature(FW_FEATURE_ISERIES)) {
|
|
if (pci_probe_only)
|
|
pcibios_claim_of_setup();
|
|
else
|
|
/* FIXME: `else' will be removed when
|
|
pci_assign_unassigned_resources() is able to work
|
|
correctly with [partially] allocated PCI tree. */
|
|
pci_assign_unassigned_resources();
|
|
}
|
|
|
|
/* Call machine dependent final fixup */
|
|
if (ppc_md.pcibios_fixup)
|
|
ppc_md.pcibios_fixup();
|
|
|
|
/* Cache the location of the ISA bridge (if we have one) */
|
|
ppc64_isabridge_dev = pci_get_class(PCI_CLASS_BRIDGE_ISA << 8, NULL);
|
|
if (ppc64_isabridge_dev != NULL)
|
|
printk(KERN_DEBUG "ISA bridge at %s\n", pci_name(ppc64_isabridge_dev));
|
|
|
|
#ifdef CONFIG_PPC_MULTIPLATFORM
|
|
if (!firmware_has_feature(FW_FEATURE_ISERIES))
|
|
/* map in PCI I/O space */
|
|
phbs_remap_io();
|
|
#endif
|
|
|
|
printk(KERN_DEBUG "PCI: Probing PCI hardware done\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
subsys_initcall(pcibios_init);
|
|
|
|
char __init *pcibios_setup(char *str)
|
|
{
|
|
return str;
|
|
}
|
|
|
|
int pcibios_enable_device(struct pci_dev *dev, int mask)
|
|
{
|
|
u16 cmd, oldcmd;
|
|
int i;
|
|
|
|
pci_read_config_word(dev, PCI_COMMAND, &cmd);
|
|
oldcmd = cmd;
|
|
|
|
for (i = 0; i < PCI_NUM_RESOURCES; i++) {
|
|
struct resource *res = &dev->resource[i];
|
|
|
|
/* Only set up the requested stuff */
|
|
if (!(mask & (1<<i)))
|
|
continue;
|
|
|
|
if (res->flags & IORESOURCE_IO)
|
|
cmd |= PCI_COMMAND_IO;
|
|
if (res->flags & IORESOURCE_MEM)
|
|
cmd |= PCI_COMMAND_MEMORY;
|
|
}
|
|
|
|
if (cmd != oldcmd) {
|
|
printk(KERN_DEBUG "PCI: Enabling device: (%s), cmd %x\n",
|
|
pci_name(dev), cmd);
|
|
/* Enable the appropriate bits in the PCI command register. */
|
|
pci_write_config_word(dev, PCI_COMMAND, cmd);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Return the domain number for this bus.
|
|
*/
|
|
int pci_domain_nr(struct pci_bus *bus)
|
|
{
|
|
if (firmware_has_feature(FW_FEATURE_ISERIES))
|
|
return 0;
|
|
else {
|
|
struct pci_controller *hose = pci_bus_to_host(bus);
|
|
|
|
return hose->global_number;
|
|
}
|
|
}
|
|
|
|
EXPORT_SYMBOL(pci_domain_nr);
|
|
|
|
/* Decide whether to display the domain number in /proc */
|
|
int pci_proc_domain(struct pci_bus *bus)
|
|
{
|
|
if (firmware_has_feature(FW_FEATURE_ISERIES))
|
|
return 0;
|
|
else {
|
|
struct pci_controller *hose = pci_bus_to_host(bus);
|
|
return hose->buid;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Platform support for /proc/bus/pci/X/Y mmap()s,
|
|
* modelled on the sparc64 implementation by Dave Miller.
|
|
* -- paulus.
|
|
*/
|
|
|
|
/*
|
|
* Adjust vm_pgoff of VMA such that it is the physical page offset
|
|
* corresponding to the 32-bit pci bus offset for DEV requested by the user.
|
|
*
|
|
* Basically, the user finds the base address for his device which he wishes
|
|
* to mmap. They read the 32-bit value from the config space base register,
|
|
* add whatever PAGE_SIZE multiple offset they wish, and feed this into the
|
|
* offset parameter of mmap on /proc/bus/pci/XXX for that device.
|
|
*
|
|
* Returns negative error code on failure, zero on success.
|
|
*/
|
|
static struct resource *__pci_mmap_make_offset(struct pci_dev *dev,
|
|
unsigned long *offset,
|
|
enum pci_mmap_state mmap_state)
|
|
{
|
|
struct pci_controller *hose = pci_bus_to_host(dev->bus);
|
|
unsigned long io_offset = 0;
|
|
int i, res_bit;
|
|
|
|
if (hose == 0)
|
|
return NULL; /* should never happen */
|
|
|
|
/* If memory, add on the PCI bridge address offset */
|
|
if (mmap_state == pci_mmap_mem) {
|
|
*offset += hose->pci_mem_offset;
|
|
res_bit = IORESOURCE_MEM;
|
|
} else {
|
|
io_offset = (unsigned long)hose->io_base_virt - pci_io_base;
|
|
*offset += io_offset;
|
|
res_bit = IORESOURCE_IO;
|
|
}
|
|
|
|
/*
|
|
* Check that the offset requested corresponds to one of the
|
|
* resources of the device.
|
|
*/
|
|
for (i = 0; i <= PCI_ROM_RESOURCE; i++) {
|
|
struct resource *rp = &dev->resource[i];
|
|
int flags = rp->flags;
|
|
|
|
/* treat ROM as memory (should be already) */
|
|
if (i == PCI_ROM_RESOURCE)
|
|
flags |= IORESOURCE_MEM;
|
|
|
|
/* Active and same type? */
|
|
if ((flags & res_bit) == 0)
|
|
continue;
|
|
|
|
/* In the range of this resource? */
|
|
if (*offset < (rp->start & PAGE_MASK) || *offset > rp->end)
|
|
continue;
|
|
|
|
/* found it! construct the final physical address */
|
|
if (mmap_state == pci_mmap_io)
|
|
*offset += hose->io_base_phys - io_offset;
|
|
return rp;
|
|
}
|
|
|
|
return NULL;
|
|
}
|
|
|
|
/*
|
|
* Set vm_page_prot of VMA, as appropriate for this architecture, for a pci
|
|
* device mapping.
|
|
*/
|
|
static pgprot_t __pci_mmap_set_pgprot(struct pci_dev *dev, struct resource *rp,
|
|
pgprot_t protection,
|
|
enum pci_mmap_state mmap_state,
|
|
int write_combine)
|
|
{
|
|
unsigned long prot = pgprot_val(protection);
|
|
|
|
/* Write combine is always 0 on non-memory space mappings. On
|
|
* memory space, if the user didn't pass 1, we check for a
|
|
* "prefetchable" resource. This is a bit hackish, but we use
|
|
* this to workaround the inability of /sysfs to provide a write
|
|
* combine bit
|
|
*/
|
|
if (mmap_state != pci_mmap_mem)
|
|
write_combine = 0;
|
|
else if (write_combine == 0) {
|
|
if (rp->flags & IORESOURCE_PREFETCH)
|
|
write_combine = 1;
|
|
}
|
|
|
|
/* XXX would be nice to have a way to ask for write-through */
|
|
prot |= _PAGE_NO_CACHE;
|
|
if (write_combine)
|
|
prot &= ~_PAGE_GUARDED;
|
|
else
|
|
prot |= _PAGE_GUARDED;
|
|
|
|
printk(KERN_DEBUG "PCI map for %s:%lx, prot: %lx\n", pci_name(dev), rp->start,
|
|
prot);
|
|
|
|
return __pgprot(prot);
|
|
}
|
|
|
|
/*
|
|
* This one is used by /dev/mem and fbdev who have no clue about the
|
|
* PCI device, it tries to find the PCI device first and calls the
|
|
* above routine
|
|
*/
|
|
pgprot_t pci_phys_mem_access_prot(struct file *file,
|
|
unsigned long pfn,
|
|
unsigned long size,
|
|
pgprot_t protection)
|
|
{
|
|
struct pci_dev *pdev = NULL;
|
|
struct resource *found = NULL;
|
|
unsigned long prot = pgprot_val(protection);
|
|
unsigned long offset = pfn << PAGE_SHIFT;
|
|
int i;
|
|
|
|
if (page_is_ram(pfn))
|
|
return __pgprot(prot);
|
|
|
|
prot |= _PAGE_NO_CACHE | _PAGE_GUARDED;
|
|
|
|
for_each_pci_dev(pdev) {
|
|
for (i = 0; i <= PCI_ROM_RESOURCE; i++) {
|
|
struct resource *rp = &pdev->resource[i];
|
|
int flags = rp->flags;
|
|
|
|
/* Active and same type? */
|
|
if ((flags & IORESOURCE_MEM) == 0)
|
|
continue;
|
|
/* In the range of this resource? */
|
|
if (offset < (rp->start & PAGE_MASK) ||
|
|
offset > rp->end)
|
|
continue;
|
|
found = rp;
|
|
break;
|
|
}
|
|
if (found)
|
|
break;
|
|
}
|
|
if (found) {
|
|
if (found->flags & IORESOURCE_PREFETCH)
|
|
prot &= ~_PAGE_GUARDED;
|
|
pci_dev_put(pdev);
|
|
}
|
|
|
|
DBG("non-PCI map for %lx, prot: %lx\n", offset, prot);
|
|
|
|
return __pgprot(prot);
|
|
}
|
|
|
|
|
|
/*
|
|
* Perform the actual remap of the pages for a PCI device mapping, as
|
|
* appropriate for this architecture. The region in the process to map
|
|
* is described by vm_start and vm_end members of VMA, the base physical
|
|
* address is found in vm_pgoff.
|
|
* The pci device structure is provided so that architectures may make mapping
|
|
* decisions on a per-device or per-bus basis.
|
|
*
|
|
* Returns a negative error code on failure, zero on success.
|
|
*/
|
|
int pci_mmap_page_range(struct pci_dev *dev, struct vm_area_struct *vma,
|
|
enum pci_mmap_state mmap_state, int write_combine)
|
|
{
|
|
unsigned long offset = vma->vm_pgoff << PAGE_SHIFT;
|
|
struct resource *rp;
|
|
int ret;
|
|
|
|
rp = __pci_mmap_make_offset(dev, &offset, mmap_state);
|
|
if (rp == NULL)
|
|
return -EINVAL;
|
|
|
|
vma->vm_pgoff = offset >> PAGE_SHIFT;
|
|
vma->vm_page_prot = __pci_mmap_set_pgprot(dev, rp,
|
|
vma->vm_page_prot,
|
|
mmap_state, write_combine);
|
|
|
|
ret = remap_pfn_range(vma, vma->vm_start, vma->vm_pgoff,
|
|
vma->vm_end - vma->vm_start, vma->vm_page_prot);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static ssize_t pci_show_devspec(struct device *dev,
|
|
struct device_attribute *attr, char *buf)
|
|
{
|
|
struct pci_dev *pdev;
|
|
struct device_node *np;
|
|
|
|
pdev = to_pci_dev (dev);
|
|
np = pci_device_to_OF_node(pdev);
|
|
if (np == NULL || np->full_name == NULL)
|
|
return 0;
|
|
return sprintf(buf, "%s", np->full_name);
|
|
}
|
|
static DEVICE_ATTR(devspec, S_IRUGO, pci_show_devspec, NULL);
|
|
|
|
void pcibios_add_platform_entries(struct pci_dev *pdev)
|
|
{
|
|
device_create_file(&pdev->dev, &dev_attr_devspec);
|
|
}
|
|
|
|
#ifdef CONFIG_PPC_MULTIPLATFORM
|
|
|
|
#define ISA_SPACE_MASK 0x1
|
|
#define ISA_SPACE_IO 0x1
|
|
|
|
static void __devinit pci_process_ISA_OF_ranges(struct device_node *isa_node,
|
|
unsigned long phb_io_base_phys,
|
|
void __iomem * phb_io_base_virt)
|
|
{
|
|
/* Remove these asap */
|
|
|
|
struct pci_address {
|
|
u32 a_hi;
|
|
u32 a_mid;
|
|
u32 a_lo;
|
|
};
|
|
|
|
struct isa_address {
|
|
u32 a_hi;
|
|
u32 a_lo;
|
|
};
|
|
|
|
struct isa_range {
|
|
struct isa_address isa_addr;
|
|
struct pci_address pci_addr;
|
|
unsigned int size;
|
|
};
|
|
|
|
const struct isa_range *range;
|
|
unsigned long pci_addr;
|
|
unsigned int isa_addr;
|
|
unsigned int size;
|
|
int rlen = 0;
|
|
|
|
range = get_property(isa_node, "ranges", &rlen);
|
|
if (range == NULL || (rlen < sizeof(struct isa_range))) {
|
|
printk(KERN_ERR "no ISA ranges or unexpected isa range size,"
|
|
"mapping 64k\n");
|
|
__ioremap_explicit(phb_io_base_phys,
|
|
(unsigned long)phb_io_base_virt,
|
|
0x10000, _PAGE_NO_CACHE | _PAGE_GUARDED);
|
|
return;
|
|
}
|
|
|
|
/* From "ISA Binding to 1275"
|
|
* The ranges property is laid out as an array of elements,
|
|
* each of which comprises:
|
|
* cells 0 - 1: an ISA address
|
|
* cells 2 - 4: a PCI address
|
|
* (size depending on dev->n_addr_cells)
|
|
* cell 5: the size of the range
|
|
*/
|
|
if ((range->isa_addr.a_hi && ISA_SPACE_MASK) == ISA_SPACE_IO) {
|
|
isa_addr = range->isa_addr.a_lo;
|
|
pci_addr = (unsigned long) range->pci_addr.a_mid << 32 |
|
|
range->pci_addr.a_lo;
|
|
|
|
/* Assume these are both zero */
|
|
if ((pci_addr != 0) || (isa_addr != 0)) {
|
|
printk(KERN_ERR "unexpected isa to pci mapping: %s\n",
|
|
__FUNCTION__);
|
|
return;
|
|
}
|
|
|
|
size = PAGE_ALIGN(range->size);
|
|
|
|
__ioremap_explicit(phb_io_base_phys,
|
|
(unsigned long) phb_io_base_virt,
|
|
size, _PAGE_NO_CACHE | _PAGE_GUARDED);
|
|
}
|
|
}
|
|
|
|
void __devinit pci_process_bridge_OF_ranges(struct pci_controller *hose,
|
|
struct device_node *dev, int prim)
|
|
{
|
|
const unsigned int *ranges;
|
|
unsigned int pci_space;
|
|
unsigned long size;
|
|
int rlen = 0;
|
|
int memno = 0;
|
|
struct resource *res;
|
|
int np, na = prom_n_addr_cells(dev);
|
|
unsigned long pci_addr, cpu_phys_addr;
|
|
|
|
np = na + 5;
|
|
|
|
/* From "PCI Binding to 1275"
|
|
* The ranges property is laid out as an array of elements,
|
|
* each of which comprises:
|
|
* cells 0 - 2: a PCI address
|
|
* cells 3 or 3+4: a CPU physical address
|
|
* (size depending on dev->n_addr_cells)
|
|
* cells 4+5 or 5+6: the size of the range
|
|
*/
|
|
ranges = get_property(dev, "ranges", &rlen);
|
|
if (ranges == NULL)
|
|
return;
|
|
hose->io_base_phys = 0;
|
|
while ((rlen -= np * sizeof(unsigned int)) >= 0) {
|
|
res = NULL;
|
|
pci_space = ranges[0];
|
|
pci_addr = ((unsigned long)ranges[1] << 32) | ranges[2];
|
|
|
|
cpu_phys_addr = ranges[3];
|
|
if (na >= 2)
|
|
cpu_phys_addr = (cpu_phys_addr << 32) | ranges[4];
|
|
|
|
size = ((unsigned long)ranges[na+3] << 32) | ranges[na+4];
|
|
ranges += np;
|
|
if (size == 0)
|
|
continue;
|
|
|
|
/* Now consume following elements while they are contiguous */
|
|
while (rlen >= np * sizeof(unsigned int)) {
|
|
unsigned long addr, phys;
|
|
|
|
if (ranges[0] != pci_space)
|
|
break;
|
|
addr = ((unsigned long)ranges[1] << 32) | ranges[2];
|
|
phys = ranges[3];
|
|
if (na >= 2)
|
|
phys = (phys << 32) | ranges[4];
|
|
if (addr != pci_addr + size ||
|
|
phys != cpu_phys_addr + size)
|
|
break;
|
|
|
|
size += ((unsigned long)ranges[na+3] << 32)
|
|
| ranges[na+4];
|
|
ranges += np;
|
|
rlen -= np * sizeof(unsigned int);
|
|
}
|
|
|
|
switch ((pci_space >> 24) & 0x3) {
|
|
case 1: /* I/O space */
|
|
hose->io_base_phys = cpu_phys_addr;
|
|
hose->pci_io_size = size;
|
|
|
|
res = &hose->io_resource;
|
|
res->flags = IORESOURCE_IO;
|
|
res->start = pci_addr;
|
|
DBG("phb%d: IO 0x%lx -> 0x%lx\n", hose->global_number,
|
|
res->start, res->start + size - 1);
|
|
break;
|
|
case 2: /* memory space */
|
|
memno = 0;
|
|
while (memno < 3 && hose->mem_resources[memno].flags)
|
|
++memno;
|
|
|
|
if (memno == 0)
|
|
hose->pci_mem_offset = cpu_phys_addr - pci_addr;
|
|
if (memno < 3) {
|
|
res = &hose->mem_resources[memno];
|
|
res->flags = IORESOURCE_MEM;
|
|
res->start = cpu_phys_addr;
|
|
DBG("phb%d: MEM 0x%lx -> 0x%lx\n", hose->global_number,
|
|
res->start, res->start + size - 1);
|
|
}
|
|
break;
|
|
}
|
|
if (res != NULL) {
|
|
res->name = dev->full_name;
|
|
res->end = res->start + size - 1;
|
|
res->parent = NULL;
|
|
res->sibling = NULL;
|
|
res->child = NULL;
|
|
}
|
|
}
|
|
}
|
|
|
|
void __init pci_setup_phb_io(struct pci_controller *hose, int primary)
|
|
{
|
|
unsigned long size = hose->pci_io_size;
|
|
unsigned long io_virt_offset;
|
|
struct resource *res;
|
|
struct device_node *isa_dn;
|
|
|
|
hose->io_base_virt = reserve_phb_iospace(size);
|
|
DBG("phb%d io_base_phys 0x%lx io_base_virt 0x%lx\n",
|
|
hose->global_number, hose->io_base_phys,
|
|
(unsigned long) hose->io_base_virt);
|
|
|
|
if (primary) {
|
|
pci_io_base = (unsigned long)hose->io_base_virt;
|
|
isa_dn = of_find_node_by_type(NULL, "isa");
|
|
if (isa_dn) {
|
|
isa_io_base = pci_io_base;
|
|
pci_process_ISA_OF_ranges(isa_dn, hose->io_base_phys,
|
|
hose->io_base_virt);
|
|
of_node_put(isa_dn);
|
|
}
|
|
}
|
|
|
|
io_virt_offset = (unsigned long)hose->io_base_virt - pci_io_base;
|
|
res = &hose->io_resource;
|
|
res->start += io_virt_offset;
|
|
res->end += io_virt_offset;
|
|
}
|
|
|
|
void __devinit pci_setup_phb_io_dynamic(struct pci_controller *hose,
|
|
int primary)
|
|
{
|
|
unsigned long size = hose->pci_io_size;
|
|
unsigned long io_virt_offset;
|
|
struct resource *res;
|
|
|
|
hose->io_base_virt = __ioremap(hose->io_base_phys, size,
|
|
_PAGE_NO_CACHE | _PAGE_GUARDED);
|
|
DBG("phb%d io_base_phys 0x%lx io_base_virt 0x%lx\n",
|
|
hose->global_number, hose->io_base_phys,
|
|
(unsigned long) hose->io_base_virt);
|
|
|
|
if (primary)
|
|
pci_io_base = (unsigned long)hose->io_base_virt;
|
|
|
|
io_virt_offset = (unsigned long)hose->io_base_virt - pci_io_base;
|
|
res = &hose->io_resource;
|
|
res->start += io_virt_offset;
|
|
res->end += io_virt_offset;
|
|
}
|
|
|
|
|
|
static int get_bus_io_range(struct pci_bus *bus, unsigned long *start_phys,
|
|
unsigned long *start_virt, unsigned long *size)
|
|
{
|
|
struct pci_controller *hose = pci_bus_to_host(bus);
|
|
struct pci_bus_region region;
|
|
struct resource *res;
|
|
|
|
if (bus->self) {
|
|
res = bus->resource[0];
|
|
pcibios_resource_to_bus(bus->self, ®ion, res);
|
|
*start_phys = hose->io_base_phys + region.start;
|
|
*start_virt = (unsigned long) hose->io_base_virt +
|
|
region.start;
|
|
if (region.end > region.start)
|
|
*size = region.end - region.start + 1;
|
|
else {
|
|
printk("%s(): unexpected region 0x%lx->0x%lx\n",
|
|
__FUNCTION__, region.start, region.end);
|
|
return 1;
|
|
}
|
|
|
|
} else {
|
|
/* Root Bus */
|
|
res = &hose->io_resource;
|
|
*start_phys = hose->io_base_phys;
|
|
*start_virt = (unsigned long) hose->io_base_virt;
|
|
if (res->end > res->start)
|
|
*size = res->end - res->start + 1;
|
|
else {
|
|
printk("%s(): unexpected region 0x%lx->0x%lx\n",
|
|
__FUNCTION__, res->start, res->end);
|
|
return 1;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
int unmap_bus_range(struct pci_bus *bus)
|
|
{
|
|
unsigned long start_phys;
|
|
unsigned long start_virt;
|
|
unsigned long size;
|
|
|
|
if (!bus) {
|
|
printk(KERN_ERR "%s() expected bus\n", __FUNCTION__);
|
|
return 1;
|
|
}
|
|
|
|
if (get_bus_io_range(bus, &start_phys, &start_virt, &size))
|
|
return 1;
|
|
if (iounmap_explicit((void __iomem *) start_virt, size))
|
|
return 1;
|
|
|
|
return 0;
|
|
}
|
|
EXPORT_SYMBOL(unmap_bus_range);
|
|
|
|
int remap_bus_range(struct pci_bus *bus)
|
|
{
|
|
unsigned long start_phys;
|
|
unsigned long start_virt;
|
|
unsigned long size;
|
|
|
|
if (!bus) {
|
|
printk(KERN_ERR "%s() expected bus\n", __FUNCTION__);
|
|
return 1;
|
|
}
|
|
|
|
|
|
if (get_bus_io_range(bus, &start_phys, &start_virt, &size))
|
|
return 1;
|
|
if (start_phys == 0)
|
|
return 1;
|
|
printk(KERN_DEBUG "mapping IO %lx -> %lx, size: %lx\n", start_phys, start_virt, size);
|
|
if (__ioremap_explicit(start_phys, start_virt, size,
|
|
_PAGE_NO_CACHE | _PAGE_GUARDED))
|
|
return 1;
|
|
|
|
return 0;
|
|
}
|
|
EXPORT_SYMBOL(remap_bus_range);
|
|
|
|
static void phbs_remap_io(void)
|
|
{
|
|
struct pci_controller *hose, *tmp;
|
|
|
|
list_for_each_entry_safe(hose, tmp, &hose_list, list_node)
|
|
remap_bus_range(hose->bus);
|
|
}
|
|
|
|
static void __devinit fixup_resource(struct resource *res, struct pci_dev *dev)
|
|
{
|
|
struct pci_controller *hose = pci_bus_to_host(dev->bus);
|
|
unsigned long offset;
|
|
|
|
if (res->flags & IORESOURCE_IO) {
|
|
offset = (unsigned long)hose->io_base_virt - pci_io_base;
|
|
|
|
res->start += offset;
|
|
res->end += offset;
|
|
} else if (res->flags & IORESOURCE_MEM) {
|
|
res->start += hose->pci_mem_offset;
|
|
res->end += hose->pci_mem_offset;
|
|
}
|
|
}
|
|
|
|
void __devinit pcibios_fixup_device_resources(struct pci_dev *dev,
|
|
struct pci_bus *bus)
|
|
{
|
|
/* Update device resources. */
|
|
int i;
|
|
|
|
for (i = 0; i < PCI_NUM_RESOURCES; i++)
|
|
if (dev->resource[i].flags)
|
|
fixup_resource(&dev->resource[i], dev);
|
|
}
|
|
EXPORT_SYMBOL(pcibios_fixup_device_resources);
|
|
|
|
|
|
static void __devinit do_bus_setup(struct pci_bus *bus)
|
|
{
|
|
struct pci_dev *dev;
|
|
|
|
ppc_md.iommu_bus_setup(bus);
|
|
|
|
list_for_each_entry(dev, &bus->devices, bus_list)
|
|
ppc_md.iommu_dev_setup(dev);
|
|
|
|
if (ppc_md.irq_bus_setup)
|
|
ppc_md.irq_bus_setup(bus);
|
|
}
|
|
|
|
void __devinit pcibios_fixup_bus(struct pci_bus *bus)
|
|
{
|
|
struct pci_dev *dev = bus->self;
|
|
|
|
if (dev && pci_probe_only &&
|
|
(dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
|
|
/* This is a subordinate bridge */
|
|
|
|
pci_read_bridge_bases(bus);
|
|
pcibios_fixup_device_resources(dev, bus);
|
|
}
|
|
|
|
do_bus_setup(bus);
|
|
|
|
if (!pci_probe_only)
|
|
return;
|
|
|
|
list_for_each_entry(dev, &bus->devices, bus_list)
|
|
if ((dev->class >> 8) != PCI_CLASS_BRIDGE_PCI)
|
|
pcibios_fixup_device_resources(dev, bus);
|
|
}
|
|
EXPORT_SYMBOL(pcibios_fixup_bus);
|
|
|
|
/*
|
|
* Reads the interrupt pin to determine if interrupt is use by card.
|
|
* If the interrupt is used, then gets the interrupt line from the
|
|
* openfirmware and sets it in the pci_dev and pci_config line.
|
|
*/
|
|
int pci_read_irq_line(struct pci_dev *pci_dev)
|
|
{
|
|
struct of_irq oirq;
|
|
unsigned int virq;
|
|
|
|
DBG("Try to map irq for %s...\n", pci_name(pci_dev));
|
|
|
|
#ifdef DEBUG
|
|
memset(&oirq, 0xff, sizeof(oirq));
|
|
#endif
|
|
/* Try to get a mapping from the device-tree */
|
|
if (of_irq_map_pci(pci_dev, &oirq)) {
|
|
u8 line, pin;
|
|
|
|
/* If that fails, lets fallback to what is in the config
|
|
* space and map that through the default controller. We
|
|
* also set the type to level low since that's what PCI
|
|
* interrupts are. If your platform does differently, then
|
|
* either provide a proper interrupt tree or don't use this
|
|
* function.
|
|
*/
|
|
if (pci_read_config_byte(pci_dev, PCI_INTERRUPT_PIN, &pin))
|
|
return -1;
|
|
if (pin == 0)
|
|
return -1;
|
|
if (pci_read_config_byte(pci_dev, PCI_INTERRUPT_LINE, &line) ||
|
|
line == 0xff) {
|
|
return -1;
|
|
}
|
|
DBG(" -> no map ! Using irq line %d from PCI config\n", line);
|
|
|
|
virq = irq_create_mapping(NULL, line);
|
|
if (virq != NO_IRQ)
|
|
set_irq_type(virq, IRQ_TYPE_LEVEL_LOW);
|
|
} else {
|
|
DBG(" -> got one, spec %d cells (0x%08x 0x%08x...) on %s\n",
|
|
oirq.size, oirq.specifier[0], oirq.specifier[1],
|
|
oirq.controller->full_name);
|
|
|
|
virq = irq_create_of_mapping(oirq.controller, oirq.specifier,
|
|
oirq.size);
|
|
}
|
|
if(virq == NO_IRQ) {
|
|
DBG(" -> failed to map !\n");
|
|
return -1;
|
|
}
|
|
|
|
DBG(" -> mapped to linux irq %d\n", virq);
|
|
|
|
pci_dev->irq = virq;
|
|
pci_write_config_byte(pci_dev, PCI_INTERRUPT_LINE, virq);
|
|
|
|
return 0;
|
|
}
|
|
EXPORT_SYMBOL(pci_read_irq_line);
|
|
|
|
void pci_resource_to_user(const struct pci_dev *dev, int bar,
|
|
const struct resource *rsrc,
|
|
u64 *start, u64 *end)
|
|
{
|
|
struct pci_controller *hose = pci_bus_to_host(dev->bus);
|
|
unsigned long offset = 0;
|
|
|
|
if (hose == NULL)
|
|
return;
|
|
|
|
if (rsrc->flags & IORESOURCE_IO)
|
|
offset = pci_io_base - (unsigned long)hose->io_base_virt +
|
|
hose->io_base_phys;
|
|
|
|
*start = rsrc->start + offset;
|
|
*end = rsrc->end + offset;
|
|
}
|
|
|
|
struct pci_controller* pci_find_hose_for_OF_device(struct device_node* node)
|
|
{
|
|
if (!have_of)
|
|
return NULL;
|
|
while(node) {
|
|
struct pci_controller *hose, *tmp;
|
|
list_for_each_entry_safe(hose, tmp, &hose_list, list_node)
|
|
if (hose->arch_data == node)
|
|
return hose;
|
|
node = node->parent;
|
|
}
|
|
return NULL;
|
|
}
|
|
|
|
#endif /* CONFIG_PPC_MULTIPLATFORM */
|
|
|
|
unsigned long pci_address_to_pio(phys_addr_t address)
|
|
{
|
|
struct pci_controller *hose, *tmp;
|
|
|
|
list_for_each_entry_safe(hose, tmp, &hose_list, list_node) {
|
|
if (address >= hose->io_base_phys &&
|
|
address < (hose->io_base_phys + hose->pci_io_size)) {
|
|
unsigned long base =
|
|
(unsigned long)hose->io_base_virt - pci_io_base;
|
|
return base + (address - hose->io_base_phys);
|
|
}
|
|
}
|
|
return (unsigned int)-1;
|
|
}
|
|
EXPORT_SYMBOL_GPL(pci_address_to_pio);
|
|
|
|
|
|
#define IOBASE_BRIDGE_NUMBER 0
|
|
#define IOBASE_MEMORY 1
|
|
#define IOBASE_IO 2
|
|
#define IOBASE_ISA_IO 3
|
|
#define IOBASE_ISA_MEM 4
|
|
|
|
long sys_pciconfig_iobase(long which, unsigned long in_bus,
|
|
unsigned long in_devfn)
|
|
{
|
|
struct pci_controller* hose;
|
|
struct list_head *ln;
|
|
struct pci_bus *bus = NULL;
|
|
struct device_node *hose_node;
|
|
|
|
/* Argh ! Please forgive me for that hack, but that's the
|
|
* simplest way to get existing XFree to not lockup on some
|
|
* G5 machines... So when something asks for bus 0 io base
|
|
* (bus 0 is HT root), we return the AGP one instead.
|
|
*/
|
|
if (machine_is_compatible("MacRISC4"))
|
|
if (in_bus == 0)
|
|
in_bus = 0xf0;
|
|
|
|
/* That syscall isn't quite compatible with PCI domains, but it's
|
|
* used on pre-domains setup. We return the first match
|
|
*/
|
|
|
|
for (ln = pci_root_buses.next; ln != &pci_root_buses; ln = ln->next) {
|
|
bus = pci_bus_b(ln);
|
|
if (in_bus >= bus->number && in_bus < (bus->number + bus->subordinate))
|
|
break;
|
|
bus = NULL;
|
|
}
|
|
if (bus == NULL || bus->sysdata == NULL)
|
|
return -ENODEV;
|
|
|
|
hose_node = (struct device_node *)bus->sysdata;
|
|
hose = PCI_DN(hose_node)->phb;
|
|
|
|
switch (which) {
|
|
case IOBASE_BRIDGE_NUMBER:
|
|
return (long)hose->first_busno;
|
|
case IOBASE_MEMORY:
|
|
return (long)hose->pci_mem_offset;
|
|
case IOBASE_IO:
|
|
return (long)hose->io_base_phys;
|
|
case IOBASE_ISA_IO:
|
|
return (long)isa_io_base;
|
|
case IOBASE_ISA_MEM:
|
|
return -EINVAL;
|
|
}
|
|
|
|
return -EOPNOTSUPP;
|
|
}
|
|
|
|
#ifdef CONFIG_NUMA
|
|
int pcibus_to_node(struct pci_bus *bus)
|
|
{
|
|
struct pci_controller *phb = pci_bus_to_host(bus);
|
|
return phb->node;
|
|
}
|
|
EXPORT_SYMBOL(pcibus_to_node);
|
|
#endif
|