linux/net/Kconfig

#
# Network configuration
#

menu "Networking"

config NET
	bool "Networking support"
	---help---
	  Unless you really know what you are doing, you should say Y here.
	  The reason is that some programs need kernel networking support even
	  when running on a stand-alone machine that isn't connected to any
	  other computer.
	  
	  If you are upgrading from an older kernel, you
	  should consider updating your networking tools too because changes
	  in the kernel and the tools often go hand in hand. The tools are
	  contained in the package net-tools, the location and version number
	  of which are given in <file:Documentation/Changes>.

	  For a general introduction to Linux networking, it is highly
	  recommended to read the NET-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

# Make sure that all config symbols are dependent on NET
if NET

menu "Networking options"

config NETDEBUG
	bool "Network packet debugging"
	help
	  You can say Y here if you want to get additional messages useful in
	  debugging bad packets, but can overwhelm logs under denial of service
	  attacks.

source "net/packet/Kconfig"
source "net/unix/Kconfig"
source "net/xfrm/Kconfig"

config INET
	bool "TCP/IP networking"
	---help---
	  These are the protocols used on the Internet and on most local
	  Ethernets. It is highly recommended to say Y here (this will enlarge
	  your kernel by about 144 KB), since some programs (e.g. the X window
	  system) use TCP/IP even if your machine is not connected to any
	  other computer. You will get the so-called loopback device which
	  allows you to ping yourself (great fun, that!).

	  For an excellent introduction to Linux networking, please read the
	  Linux Networking HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  If you say Y here and also to "/proc file system support" and
	  "Sysctl support" below, you can change various aspects of the
	  behavior of the TCP/IP code by writing to the (virtual) files in
	  /proc/sys/net/ipv4/*; the options are explained in the file
	  <file:Documentation/networking/ip-sysctl.txt>.

	  Short answer: say Y.

if INET
source "net/ipv4/Kconfig"
source "net/ipv6/Kconfig"

endif # if INET

menuconfig NETFILTER
	bool "Network packet filtering (replaces ipchains)"
	---help---
	  Netfilter is a framework for filtering and mangling network packets
	  that pass through your Linux box.

	  The most common use of packet filtering is to run your Linux box as
	  a firewall protecting a local network from the Internet. The type of
	  firewall provided by this kernel support is called a "packet
	  filter", which means that it can reject individual network packets
	  based on type, source, destination etc. The other kind of firewall,
	  a "proxy-based" one, is more secure but more intrusive and more
	  bothersome to set up; it inspects the network traffic much more
	  closely, modifies it and has knowledge about the higher level
	  protocols, which a packet filter lacks. Moreover, proxy-based
	  firewalls often require changes to the programs running on the local
	  clients. Proxy-based firewalls don't need support by the kernel, but
	  they are often combined with a packet filter, which only works if
	  you say Y here.

	  You should also say Y here if you intend to use your Linux box as
	  the gateway to the Internet for a local network of machines without
	  globally valid IP addresses. This is called "masquerading": if one
	  of the computers on your local network wants to send something to
	  the outside, your box can "masquerade" as that computer, i.e. it
	  forwards the traffic to the intended outside destination, but
	  modifies the packets to make it look like they came from the
	  firewall box itself. It works both ways: if the outside host
	  replies, the Linux box will silently forward the traffic to the
	  correct local computer. This way, the computers on your local net
	  are completely invisible to the outside world, even though they can
	  reach the outside and can receive replies. It is even possible to
	  run globally visible servers from within a masqueraded local network
	  using a mechanism called portforwarding. Masquerading is also often
	  called NAT (Network Address Translation).

	  Another use of Netfilter is in transparent proxying: if a machine on
	  the local network tries to connect to an outside host, your Linux
	  box can transparently forward the traffic to a local server,
	  typically a caching proxy server.

	  Yet another use of Netfilter is building a bridging firewall. Using
	  a bridge with Network packet filtering enabled makes iptables "see"
	  the bridged traffic. For filtering on the lower network and Ethernet
	  protocols over the bridge, use ebtables (under bridge netfilter
	  configuration).

	  Various modules exist for netfilter which replace the previous
	  masquerading (ipmasqadm), packet filtering (ipchains), transparent
	  proxying, and portforwarding mechanisms. Please see
	  <file:Documentation/Changes> under "iptables" for the location of
	  these packages.

	  Make sure to say N to "Fast switching" below if you intend to say Y
	  here, as Fast switching currently bypasses netfilter.

	  Chances are that you should say Y here if you compile a kernel which
	  will run as a router and N for regular hosts. If unsure, say N.

if NETFILTER

config NETFILTER_DEBUG
	bool "Network packet filtering debugging"
	depends on NETFILTER
	help
	  You can say Y here if you want to get additional messages useful in
	  debugging the netfilter code.

config BRIDGE_NETFILTER
	bool "Bridged IP/ARP packets filtering"
	depends on BRIDGE && NETFILTER && INET
	default y
	---help---
	  Enabling this option will let arptables resp. iptables see bridged
	  ARP resp. IP traffic. If you want a bridging firewall, you probably
	  want this option enabled.
	  Enabling or disabling this option doesn't enable or disable
	  ebtables.

	  If unsure, say N.

source "net/netfilter/Kconfig"
source "net/ipv4/netfilter/Kconfig"
source "net/ipv6/netfilter/Kconfig"
source "net/decnet/netfilter/Kconfig"
source "net/bridge/netfilter/Kconfig"

endif

source "net/dccp/Kconfig"
source "net/sctp/Kconfig"
source "net/tipc/Kconfig"
source "net/atm/Kconfig"
source "net/bridge/Kconfig"
source "net/8021q/Kconfig"
source "net/decnet/Kconfig"
source "net/llc/Kconfig"
source "net/ipx/Kconfig"
source "drivers/net/appletalk/Kconfig"
source "net/x25/Kconfig"
source "net/lapb/Kconfig"

config NET_DIVERT
	bool "Frame Diverter (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	---help---
	  The Frame Diverter allows you to divert packets from the
	  network, that are not aimed at the interface receiving it (in
	  promisc. mode). Typically, a Linux box setup as an Ethernet bridge
	  with the Frames Diverter on, can do some *really* transparent www
	  caching using a Squid proxy for example.

	  This is very useful when you don't want to change your router's
	  config (or if you simply don't have access to it).

	  The other possible usages of diverting Ethernet Frames are
	  numberous:
	  - reroute smtp traffic to another interface
	  - traffic-shape certain network streams
	  - transparently proxy smtp connections
	  - etc...

	  For more informations, please refer to:
	  <http://diverter.sourceforge.net/>
	  <http://perso.wanadoo.fr/magpie/EtherDivert.html>

	  If unsure, say N.

source "net/econet/Kconfig"
source "net/wanrouter/Kconfig"
source "net/sched/Kconfig"

menu "Network testing"

config NET_PKTGEN
	tristate "Packet Generator (USE WITH CAUTION)"
	depends on PROC_FS
	---help---
	  This module will inject preconfigured packets, at a configurable
	  rate, out of a given interface.  It is used for network interface
	  stress testing and performance analysis.  If you don't understand
	  what was just said, you don't need it: say N.

	  Documentation on how to use the packet generator can be found
	  at <file:Documentation/networking/pktgen.txt>.

	  To compile this code as a module, choose M here: the
	  module will be called pktgen.

endmenu

endmenu

source "net/ax25/Kconfig"
source "net/irda/Kconfig"
source "net/bluetooth/Kconfig"
source "net/ieee80211/Kconfig"

config WIRELESS_EXT
	bool

endif   # if NET
endmenu # Networking