mirror of
https://github.com/FEX-Emu/linux.git
synced 2024-12-28 12:25:31 +00:00
68d03da2ae
The pads capable of being used as GPIOs had their pad-name and mode-name switched. Also, fix the following: - Whitespace fixes - Replace IOMUX_CONFIG_ALTn with 'n' Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
292 lines
7.6 KiB
C
292 lines
7.6 KiB
C
/*
|
|
* Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
|
|
* Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria@canonical.com>
|
|
*
|
|
* The code contained herein is licensed under the GNU General Public
|
|
* License. You may obtain a copy of the GNU General Public License
|
|
* Version 2 or later at the following locations:
|
|
*
|
|
* http://www.opensource.org/licenses/gpl-license.html
|
|
* http://www.gnu.org/copyleft/gpl.html
|
|
*/
|
|
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/io.h>
|
|
#include <linux/fsl_devices.h>
|
|
|
|
#include <mach/common.h>
|
|
#include <mach/hardware.h>
|
|
#include <mach/imx-uart.h>
|
|
#include <mach/iomux-mx51.h>
|
|
#include <mach/i2c.h>
|
|
#include <mach/mxc_ehci.h>
|
|
|
|
#include <asm/irq.h>
|
|
#include <asm/setup.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/time.h>
|
|
|
|
#include "devices.h"
|
|
|
|
#define BABBAGE_USB_HUB_RESET (0*32 + 7) /* GPIO_1_7 */
|
|
#define BABBAGE_USBH1_STP (0*32 + 27) /* GPIO_1_27 */
|
|
#define BABBAGE_PHY_RESET (1*32 +5) /* GPIO_2_5 */
|
|
|
|
/* USB_CTRL_1 */
|
|
#define MX51_USB_CTRL_1_OFFSET 0x10
|
|
#define MX51_USB_CTRL_UH1_EXT_CLK_EN (1 << 25)
|
|
|
|
#define MX51_USB_PLLDIV_12_MHZ 0x00
|
|
#define MX51_USB_PLL_DIV_19_2_MHZ 0x01
|
|
#define MX51_USB_PLL_DIV_24_MHZ 0x02
|
|
|
|
static struct platform_device *devices[] __initdata = {
|
|
&mxc_fec_device,
|
|
};
|
|
|
|
static struct pad_desc mx51babbage_pads[] = {
|
|
/* UART1 */
|
|
MX51_PAD_UART1_RXD__UART1_RXD,
|
|
MX51_PAD_UART1_TXD__UART1_TXD,
|
|
MX51_PAD_UART1_RTS__UART1_RTS,
|
|
MX51_PAD_UART1_CTS__UART1_CTS,
|
|
|
|
/* UART2 */
|
|
MX51_PAD_UART2_RXD__UART2_RXD,
|
|
MX51_PAD_UART2_TXD__UART2_TXD,
|
|
|
|
/* UART3 */
|
|
MX51_PAD_EIM_D25__UART3_RXD,
|
|
MX51_PAD_EIM_D26__UART3_TXD,
|
|
MX51_PAD_EIM_D27__UART3_RTS,
|
|
MX51_PAD_EIM_D24__UART3_CTS,
|
|
|
|
/* I2C1 */
|
|
MX51_PAD_EIM_D16__I2C1_SDA,
|
|
MX51_PAD_EIM_D19__I2C1_SCL,
|
|
|
|
/* I2C2 */
|
|
MX51_PAD_KEY_COL4__I2C2_SCL,
|
|
MX51_PAD_KEY_COL5__I2C2_SDA,
|
|
|
|
/* HSI2C */
|
|
MX51_PAD_I2C1_CLK__HSI2C_CLK,
|
|
MX51_PAD_I2C1_DAT__HSI2C_DAT,
|
|
|
|
/* USB HOST1 */
|
|
MX51_PAD_USBH1_CLK__USBH1_CLK,
|
|
MX51_PAD_USBH1_DIR__USBH1_DIR,
|
|
MX51_PAD_USBH1_NXT__USBH1_NXT,
|
|
MX51_PAD_USBH1_DATA0__USBH1_DATA0,
|
|
MX51_PAD_USBH1_DATA1__USBH1_DATA1,
|
|
MX51_PAD_USBH1_DATA2__USBH1_DATA2,
|
|
MX51_PAD_USBH1_DATA3__USBH1_DATA3,
|
|
MX51_PAD_USBH1_DATA4__USBH1_DATA4,
|
|
MX51_PAD_USBH1_DATA5__USBH1_DATA5,
|
|
MX51_PAD_USBH1_DATA6__USBH1_DATA6,
|
|
MX51_PAD_USBH1_DATA7__USBH1_DATA7,
|
|
|
|
/* USB HUB reset line*/
|
|
MX51_PAD_GPIO_1_7__GPIO_1_7,
|
|
};
|
|
|
|
/* Serial ports */
|
|
#if defined(CONFIG_SERIAL_IMX) || defined(CONFIG_SERIAL_IMX_MODULE)
|
|
static struct imxuart_platform_data uart_pdata = {
|
|
.flags = IMXUART_HAVE_RTSCTS,
|
|
};
|
|
|
|
static inline void mxc_init_imx_uart(void)
|
|
{
|
|
mxc_register_device(&mxc_uart_device0, &uart_pdata);
|
|
mxc_register_device(&mxc_uart_device1, &uart_pdata);
|
|
mxc_register_device(&mxc_uart_device2, &uart_pdata);
|
|
}
|
|
#else /* !SERIAL_IMX */
|
|
static inline void mxc_init_imx_uart(void)
|
|
{
|
|
}
|
|
#endif /* SERIAL_IMX */
|
|
|
|
static struct imxi2c_platform_data babbage_i2c_data = {
|
|
.bitrate = 100000,
|
|
};
|
|
|
|
static struct imxi2c_platform_data babbage_hsi2c_data = {
|
|
.bitrate = 400000,
|
|
};
|
|
|
|
static int gpio_usbh1_active(void)
|
|
{
|
|
struct pad_desc usbh1stp_gpio = MX51_PAD_USBH1_STP__GPIO_1_27;
|
|
struct pad_desc phyreset_gpio = MX51_PAD_EIM_D21__GPIO_2_5;
|
|
int ret;
|
|
|
|
/* Set USBH1_STP to GPIO and toggle it */
|
|
mxc_iomux_v3_setup_pad(&usbh1stp_gpio);
|
|
ret = gpio_request(BABBAGE_USBH1_STP, "usbh1_stp");
|
|
|
|
if (ret) {
|
|
pr_debug("failed to get MX51_PAD_USBH1_STP__GPIO_1_27: %d\n", ret);
|
|
return ret;
|
|
}
|
|
gpio_direction_output(BABBAGE_USBH1_STP, 0);
|
|
gpio_set_value(BABBAGE_USBH1_STP, 1);
|
|
msleep(100);
|
|
gpio_free(BABBAGE_USBH1_STP);
|
|
|
|
/* De-assert USB PHY RESETB */
|
|
mxc_iomux_v3_setup_pad(&phyreset_gpio);
|
|
ret = gpio_request(BABBAGE_PHY_RESET, "phy_reset");
|
|
|
|
if (ret) {
|
|
pr_debug("failed to get MX51_PAD_EIM_D21__GPIO_2_5: %d\n", ret);
|
|
return ret;
|
|
}
|
|
gpio_direction_output(BABBAGE_PHY_RESET, 1);
|
|
return 0;
|
|
}
|
|
|
|
static inline void babbage_usbhub_reset(void)
|
|
{
|
|
int ret;
|
|
|
|
/* Bring USB hub out of reset */
|
|
ret = gpio_request(BABBAGE_USB_HUB_RESET, "GPIO1_7");
|
|
if (ret) {
|
|
printk(KERN_ERR"failed to get GPIO_USB_HUB_RESET: %d\n", ret);
|
|
return;
|
|
}
|
|
gpio_direction_output(BABBAGE_USB_HUB_RESET, 0);
|
|
|
|
/* USB HUB RESET - De-assert USB HUB RESET_N */
|
|
msleep(1);
|
|
gpio_set_value(BABBAGE_USB_HUB_RESET, 0);
|
|
msleep(1);
|
|
gpio_set_value(BABBAGE_USB_HUB_RESET, 1);
|
|
}
|
|
|
|
/* This function is board specific as the bit mask for the plldiv will also
|
|
be different for other Freescale SoCs, thus a common bitmask is not
|
|
possible and cannot get place in /plat-mxc/ehci.c.*/
|
|
static int initialize_otg_port(struct platform_device *pdev)
|
|
{
|
|
u32 v;
|
|
void __iomem *usb_base;
|
|
u32 usbother_base;
|
|
|
|
usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
|
|
usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
|
|
|
|
/* Set the PHY clock to 19.2MHz */
|
|
v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
|
|
v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
|
|
v |= MX51_USB_PLL_DIV_19_2_MHZ;
|
|
__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
|
|
iounmap(usb_base);
|
|
return 0;
|
|
}
|
|
|
|
static int initialize_usbh1_port(struct platform_device *pdev)
|
|
{
|
|
u32 v;
|
|
void __iomem *usb_base;
|
|
u32 usbother_base;
|
|
|
|
usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
|
|
usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
|
|
|
|
/* The clock for the USBH1 ULPI port will come externally from the PHY. */
|
|
v = __raw_readl(usbother_base + MX51_USB_CTRL_1_OFFSET);
|
|
__raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN, usbother_base + MX51_USB_CTRL_1_OFFSET);
|
|
iounmap(usb_base);
|
|
return 0;
|
|
}
|
|
|
|
static struct mxc_usbh_platform_data dr_utmi_config = {
|
|
.init = initialize_otg_port,
|
|
.portsc = MXC_EHCI_UTMI_16BIT,
|
|
.flags = MXC_EHCI_INTERNAL_PHY,
|
|
};
|
|
|
|
static struct fsl_usb2_platform_data usb_pdata = {
|
|
.operating_mode = FSL_USB2_DR_DEVICE,
|
|
.phy_mode = FSL_USB2_PHY_UTMI_WIDE,
|
|
};
|
|
|
|
static struct mxc_usbh_platform_data usbh1_config = {
|
|
.init = initialize_usbh1_port,
|
|
.portsc = MXC_EHCI_MODE_ULPI,
|
|
.flags = (MXC_EHCI_POWER_PINS_ENABLED | MXC_EHCI_ITC_NO_THRESHOLD),
|
|
};
|
|
|
|
static int otg_mode_host;
|
|
|
|
static int __init babbage_otg_mode(char *options)
|
|
{
|
|
if (!strcmp(options, "host"))
|
|
otg_mode_host = 1;
|
|
else if (!strcmp(options, "device"))
|
|
otg_mode_host = 0;
|
|
else
|
|
pr_info("otg_mode neither \"host\" nor \"device\". "
|
|
"Defaulting to device\n");
|
|
return 0;
|
|
}
|
|
__setup("otg_mode=", babbage_otg_mode);
|
|
|
|
/*
|
|
* Board specific initialization.
|
|
*/
|
|
static void __init mxc_board_init(void)
|
|
{
|
|
struct pad_desc usbh1stp = MX51_PAD_USBH1_STP__USBH1_STP;
|
|
|
|
mxc_iomux_v3_setup_multiple_pads(mx51babbage_pads,
|
|
ARRAY_SIZE(mx51babbage_pads));
|
|
mxc_init_imx_uart();
|
|
platform_add_devices(devices, ARRAY_SIZE(devices));
|
|
|
|
mxc_register_device(&mxc_i2c_device0, &babbage_i2c_data);
|
|
mxc_register_device(&mxc_i2c_device1, &babbage_i2c_data);
|
|
mxc_register_device(&mxc_hsi2c_device, &babbage_hsi2c_data);
|
|
|
|
if (otg_mode_host)
|
|
mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
|
|
else {
|
|
initialize_otg_port(NULL);
|
|
mxc_register_device(&mxc_usbdr_udc_device, &usb_pdata);
|
|
}
|
|
|
|
gpio_usbh1_active();
|
|
mxc_register_device(&mxc_usbh1_device, &usbh1_config);
|
|
/* setback USBH1_STP to be function */
|
|
mxc_iomux_v3_setup_pad(&usbh1stp);
|
|
babbage_usbhub_reset();
|
|
}
|
|
|
|
static void __init mx51_babbage_timer_init(void)
|
|
{
|
|
mx51_clocks_init(32768, 24000000, 22579200, 0);
|
|
}
|
|
|
|
static struct sys_timer mxc_timer = {
|
|
.init = mx51_babbage_timer_init,
|
|
};
|
|
|
|
MACHINE_START(MX51_BABBAGE, "Freescale MX51 Babbage Board")
|
|
/* Maintainer: Amit Kucheria <amit.kucheria@canonical.com> */
|
|
.phys_io = MX51_AIPS1_BASE_ADDR,
|
|
.io_pg_offst = ((MX51_AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc,
|
|
.boot_params = PHYS_OFFSET + 0x100,
|
|
.map_io = mx51_map_io,
|
|
.init_irq = mx51_init_irq,
|
|
.init_machine = mxc_board_init,
|
|
.timer = &mxc_timer,
|
|
MACHINE_END
|