mirror of
https://github.com/FEX-Emu/linux.git
synced 2024-12-25 10:59:05 +00:00
6ab3d5624e
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
106 lines
2.9 KiB
C
106 lines
2.9 KiB
C
/*
|
|
* arch/v850/kernel/rte_ma1_cb.c -- Midas labs RTE-V850E/MA1-CB board
|
|
*
|
|
* Copyright (C) 2001,02,03 NEC Electronics Corporation
|
|
* Copyright (C) 2001,02,03 Miles Bader <miles@gnu.org>
|
|
*
|
|
* This file is subject to the terms and conditions of the GNU General
|
|
* Public License. See the file COPYING in the main directory of this
|
|
* archive for more details.
|
|
*
|
|
* Written by Miles Bader <miles@gnu.org>
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/bootmem.h>
|
|
|
|
#include <asm/atomic.h>
|
|
#include <asm/page.h>
|
|
#include <asm/ma1.h>
|
|
#include <asm/rte_ma1_cb.h>
|
|
#include <asm/v850e_timer_c.h>
|
|
|
|
#include "mach.h"
|
|
|
|
|
|
/* SRAM and SDRAM are almost contiguous (with a small hole in between;
|
|
see mach_reserve_bootmem for details), so just use both as one big area. */
|
|
#define RAM_START SRAM_ADDR
|
|
#define RAM_END (SDRAM_ADDR + SDRAM_SIZE)
|
|
|
|
|
|
void __init mach_early_init (void)
|
|
{
|
|
rte_cb_early_init ();
|
|
}
|
|
|
|
void __init mach_get_physical_ram (unsigned long *ram_start,
|
|
unsigned long *ram_len)
|
|
{
|
|
*ram_start = RAM_START;
|
|
*ram_len = RAM_END - RAM_START;
|
|
}
|
|
|
|
void __init mach_reserve_bootmem ()
|
|
{
|
|
#ifdef CONFIG_RTE_CB_MULTI
|
|
/* Prevent the kernel from touching the monitor's scratch RAM. */
|
|
reserve_bootmem (MON_SCRATCH_ADDR, MON_SCRATCH_SIZE);
|
|
#endif
|
|
|
|
/* The space between SRAM and SDRAM is filled with duplicate
|
|
images of SRAM. Prevent the kernel from using them. */
|
|
reserve_bootmem (SRAM_ADDR + SRAM_SIZE,
|
|
SDRAM_ADDR - (SRAM_ADDR + SRAM_SIZE));
|
|
}
|
|
|
|
void mach_gettimeofday (struct timespec *tv)
|
|
{
|
|
tv->tv_sec = 0;
|
|
tv->tv_nsec = 0;
|
|
}
|
|
|
|
/* Called before configuring an on-chip UART. */
|
|
void rte_ma1_cb_uart_pre_configure (unsigned chan,
|
|
unsigned cflags, unsigned baud)
|
|
{
|
|
/* The RTE-MA1-CB connects some general-purpose I/O pins on the
|
|
CPU to the RTS/CTS lines of UART 0's serial connection.
|
|
I/O pins P42 and P43 are RTS and CTS respectively. */
|
|
if (chan == 0) {
|
|
/* Put P42 & P43 in I/O port mode. */
|
|
MA_PORT4_PMC &= ~0xC;
|
|
/* Make P42 an output, and P43 an input. */
|
|
MA_PORT4_PM = (MA_PORT4_PM & ~0xC) | 0x8;
|
|
}
|
|
|
|
/* Do pre-configuration for the actual UART. */
|
|
ma_uart_pre_configure (chan, cflags, baud);
|
|
}
|
|
|
|
void __init mach_init_irqs (void)
|
|
{
|
|
unsigned tc;
|
|
|
|
/* Initialize interrupts. */
|
|
ma_init_irqs ();
|
|
rte_cb_init_irqs ();
|
|
|
|
/* Use falling-edge-sensitivity for interrupts . */
|
|
V850E_TIMER_C_SESC (0) &= ~0xC;
|
|
V850E_TIMER_C_SESC (1) &= ~0xF;
|
|
|
|
/* INTP000-INTP011 are shared with `Timer C', so we have to set
|
|
up Timer C to pass them through as raw interrupts. */
|
|
for (tc = 0; tc < 2; tc++)
|
|
/* Turn on the timer. */
|
|
V850E_TIMER_C_TMCC0 (tc) |= V850E_TIMER_C_TMCC0_CAE;
|
|
|
|
/* Make sure the relevant port0/port1 pins are assigned
|
|
interrupt duty. We used INTP001-INTP011 (don't screw with
|
|
INTP000 because the monitor uses it). */
|
|
MA_PORT0_PMC |= 0x4; /* P02 (INTP001) in IRQ mode. */
|
|
MA_PORT1_PMC |= 0x6; /* P11 (INTP010) & P12 (INTP011) in IRQ mode.*/
|
|
}
|