mirror of
https://github.com/FEX-Emu/linux.git
synced 2024-12-21 08:53:41 +00:00
6846ee5ca6
Commit ac4c2a3bbe broke the build
of all powerpc boot wrappers.
It attempts to add an include of autoconf.h but used the wrong
path for it. It also adds -D__KERNEL__ to our boot wrapper, both
things that we pretty much didn't do on purpose so far.
We want our boot wrapper to remain independent enough of the kernel
for various reasons, one of them being that you can "wrap" an existing
kernel at distro install time which allows to ship one kernel image
and a set of boot wrappers for different platforms, the wrappers
don't have to be built out of the same kernel build tree.
It's also incorrect to do what the patch does in our boot environment
since we may not have a proper alignment exception handler which means
we may not be able to fixup the few cases where an unaligned access will
need SW emulation (depends on the core variant, could be when crossing
page or segment boundaries for example).
This patch fixes it by putting the old code back in and using the
new "fancy" variant only when CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
is set, which happens not to be set on powerpc since we don't include
autoconf.h. It also reverts the changes to our boot wrapper Makefile.
This means that x86 should, afaik, keep the optimisations since its
boot wrapper does include autoconf.h and define __KERNEL__ (though I
doubt they make that much different outside of slow embedded processors).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
409 lines
16 KiB
Makefile
409 lines
16 KiB
Makefile
# Makefile for making ELF bootable images for booting on CHRP
|
|
# using Open Firmware.
|
|
#
|
|
# Geert Uytterhoeven September 1997
|
|
#
|
|
# Based on coffboot by Paul Mackerras
|
|
# Simplified for ppc64 by Todd Inglett
|
|
#
|
|
# NOTE: this code is built for 32 bit in ELF32 format even though
|
|
# it packages a 64 bit kernel. We do this to simplify the
|
|
# bootloader and increase compatibility with OpenFirmware.
|
|
#
|
|
# To this end we need to define BOOTCC, etc, as the tools
|
|
# needed to build the 32 bit image. That's normally the same
|
|
# compiler for the rest of the kernel, with the -m32 flag added.
|
|
# To make it easier to setup a cross compiler,
|
|
# CROSS32_COMPILE is setup as a prefix just like CROSS_COMPILE
|
|
# in the toplevel makefile.
|
|
|
|
all: $(obj)/zImage
|
|
|
|
BOOTCFLAGS := -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs \
|
|
-fno-strict-aliasing -Os -msoft-float -pipe \
|
|
-fomit-frame-pointer -fno-builtin -fPIC -nostdinc \
|
|
-isystem $(shell $(CROSS32CC) -print-file-name=include)
|
|
BOOTAFLAGS := -D__ASSEMBLY__ $(BOOTCFLAGS) -traditional -nostdinc
|
|
|
|
ifdef CONFIG_DEBUG_INFO
|
|
BOOTCFLAGS += -g
|
|
endif
|
|
|
|
ifeq ($(call cc-option-yn, -fstack-protector),y)
|
|
BOOTCFLAGS += -fno-stack-protector
|
|
endif
|
|
|
|
BOOTCFLAGS += -I$(obj) -I$(srctree)/$(obj)
|
|
|
|
DTS_FLAGS ?= -p 1024
|
|
|
|
$(obj)/4xx.o: BOOTCFLAGS += -mcpu=405
|
|
$(obj)/ebony.o: BOOTCFLAGS += -mcpu=405
|
|
$(obj)/cuboot-hotfoot.o: BOOTCFLAGS += -mcpu=405
|
|
$(obj)/cuboot-taishan.o: BOOTCFLAGS += -mcpu=405
|
|
$(obj)/cuboot-katmai.o: BOOTCFLAGS += -mcpu=405
|
|
$(obj)/cuboot-acadia.o: BOOTCFLAGS += -mcpu=405
|
|
$(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405
|
|
$(obj)/virtex405-head.o: BOOTAFLAGS += -mcpu=405
|
|
|
|
|
|
zlib := inffast.c inflate.c inftrees.c
|
|
zlibheader := inffast.h inffixed.h inflate.h inftrees.h infutil.h
|
|
zliblinuxheader := zlib.h zconf.h zutil.h
|
|
|
|
$(addprefix $(obj)/,$(zlib) cuboot-c2k.o gunzip_util.o main.o prpmc2800.o): \
|
|
$(addprefix $(obj)/,$(zliblinuxheader)) $(addprefix $(obj)/,$(zlibheader))
|
|
|
|
libfdt := fdt.c fdt_ro.c fdt_wip.c fdt_sw.c fdt_rw.c fdt_strerror.c
|
|
libfdtheader := fdt.h libfdt.h libfdt_internal.h
|
|
|
|
$(addprefix $(obj)/,$(libfdt) libfdt-wrapper.o simpleboot.o): \
|
|
$(addprefix $(obj)/,$(libfdtheader))
|
|
|
|
src-wlib := string.S crt0.S crtsavres.S stdio.c main.c \
|
|
$(libfdt) libfdt-wrapper.c \
|
|
ns16550.c serial.c simple_alloc.c div64.S util.S \
|
|
gunzip_util.c elf_util.c $(zlib) devtree.c oflib.c ofconsole.c \
|
|
4xx.c ebony.c mv64x60.c mpsc.c mv64x60_i2c.c cuboot.c bamboo.c \
|
|
cpm-serial.c stdlib.c mpc52xx-psc.c planetcore.c uartlite.c \
|
|
fsl-soc.c mpc8xx.c pq2.c ugecon.c
|
|
src-plat := of.c cuboot-52xx.c cuboot-824x.c cuboot-83xx.c cuboot-85xx.c holly.c \
|
|
cuboot-ebony.c cuboot-hotfoot.c treeboot-ebony.c prpmc2800.c \
|
|
ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
|
|
cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c \
|
|
cuboot-bamboo.c cuboot-mpc7448hpc2.c cuboot-taishan.c \
|
|
fixed-head.S ep88xc.c ep405.c cuboot-c2k.c \
|
|
cuboot-katmai.c cuboot-rainier.c redboot-8xx.c ep8248e.c \
|
|
cuboot-warp.c cuboot-85xx-cpm2.c cuboot-yosemite.c simpleboot.c \
|
|
virtex405-head.S virtex.c redboot-83xx.c cuboot-sam440ep.c \
|
|
cuboot-acadia.c cuboot-amigaone.c cuboot-kilauea.c \
|
|
gamecube-head.S gamecube.c wii-head.S wii.c
|
|
src-boot := $(src-wlib) $(src-plat) empty.c
|
|
|
|
src-boot := $(addprefix $(obj)/, $(src-boot))
|
|
obj-boot := $(addsuffix .o, $(basename $(src-boot)))
|
|
obj-wlib := $(addsuffix .o, $(basename $(addprefix $(obj)/, $(src-wlib))))
|
|
obj-plat := $(addsuffix .o, $(basename $(addprefix $(obj)/, $(src-plat))))
|
|
|
|
quiet_cmd_copy_zlib = COPY $@
|
|
cmd_copy_zlib = sed "s@__used@@;s@<linux/\([^>]*\).*@\"\1\"@" $< > $@
|
|
|
|
quiet_cmd_copy_zlibheader = COPY $@
|
|
cmd_copy_zlibheader = sed "s@<linux/\([^>]*\).*@\"\1\"@" $< > $@
|
|
# stddef.h for NULL
|
|
quiet_cmd_copy_zliblinuxheader = COPY $@
|
|
cmd_copy_zliblinuxheader = sed "s@<linux/string.h>@\"string.h\"@;s@<linux/kernel.h>@<stddef.h>@;s@<linux/\([^>]*\).*@\"\1\"@" $< > $@
|
|
|
|
$(addprefix $(obj)/,$(zlib)): $(obj)/%: $(srctree)/lib/zlib_inflate/%
|
|
$(call cmd,copy_zlib)
|
|
|
|
$(addprefix $(obj)/,$(zlibheader)): $(obj)/%: $(srctree)/lib/zlib_inflate/%
|
|
$(call cmd,copy_zlibheader)
|
|
|
|
$(addprefix $(obj)/,$(zliblinuxheader)): $(obj)/%: $(srctree)/include/linux/%
|
|
$(call cmd,copy_zliblinuxheader)
|
|
|
|
quiet_cmd_copy_libfdt = COPY $@
|
|
cmd_copy_libfdt = cp $< $@
|
|
|
|
$(addprefix $(obj)/,$(libfdt) $(libfdtheader)): $(obj)/%: $(srctree)/scripts/dtc/libfdt/%
|
|
$(call cmd,copy_libfdt)
|
|
|
|
$(obj)/empty.c:
|
|
@touch $@
|
|
|
|
$(obj)/zImage.lds $(obj)/zImage.coff.lds $(obj)/zImage.ps3.lds: $(obj)/%: $(srctree)/$(src)/%.S
|
|
@cp $< $@
|
|
|
|
clean-files := $(zlib) $(zlibheader) $(zliblinuxheader) \
|
|
$(libfdt) $(libfdtheader) \
|
|
empty.c zImage.coff.lds zImage.ps3.lds zImage.lds
|
|
|
|
quiet_cmd_bootcc = BOOTCC $@
|
|
cmd_bootcc = $(CROSS32CC) -Wp,-MD,$(depfile) $(BOOTCFLAGS) -c -o $@ $<
|
|
|
|
quiet_cmd_bootas = BOOTAS $@
|
|
cmd_bootas = $(CROSS32CC) -Wp,-MD,$(depfile) $(BOOTAFLAGS) -c -o $@ $<
|
|
|
|
quiet_cmd_bootar = BOOTAR $@
|
|
cmd_bootar = $(CROSS32AR) -cr $@.$$$$ $(filter-out FORCE,$^); mv $@.$$$$ $@
|
|
|
|
$(obj-libfdt): $(obj)/%.o: $(srctree)/scripts/dtc/libfdt/%.c FORCE
|
|
$(call if_changed_dep,bootcc)
|
|
$(patsubst %.c,%.o, $(filter %.c, $(src-boot))): %.o: %.c FORCE
|
|
$(Q)mkdir -p $(dir $@)
|
|
$(call if_changed_dep,bootcc)
|
|
$(patsubst %.S,%.o, $(filter %.S, $(src-boot))): %.o: %.S FORCE
|
|
$(Q)mkdir -p $(dir $@)
|
|
$(call if_changed_dep,bootas)
|
|
|
|
$(obj)/wrapper.a: $(obj-wlib) FORCE
|
|
$(call if_changed,bootar)
|
|
|
|
hostprogs-y := addnote addRamDisk hack-coff mktree
|
|
|
|
targets += $(patsubst $(obj)/%,%,$(obj-boot) wrapper.a)
|
|
extra-y := $(obj)/wrapper.a $(obj-plat) $(obj)/empty.o \
|
|
$(obj)/zImage.lds $(obj)/zImage.coff.lds $(obj)/zImage.ps3.lds
|
|
|
|
dtstree := $(srctree)/$(src)/dts
|
|
|
|
wrapper :=$(srctree)/$(src)/wrapper
|
|
wrapperbits := $(extra-y) $(addprefix $(obj)/,addnote hack-coff mktree) \
|
|
$(wrapper) FORCE
|
|
|
|
#############
|
|
# Bits for building various flavours of zImage
|
|
|
|
ifneq ($(CROSS32_COMPILE),)
|
|
CROSSWRAP := -C "$(CROSS32_COMPILE)"
|
|
else
|
|
ifneq ($(CROSS_COMPILE),)
|
|
CROSSWRAP := -C "$(CROSS_COMPILE)"
|
|
endif
|
|
endif
|
|
|
|
# args (to if_changed): 1 = (this rule), 2 = platform, 3 = dts 4=dtb 5=initrd
|
|
quiet_cmd_wrap = WRAP $@
|
|
cmd_wrap =$(CONFIG_SHELL) $(wrapper) -c -o $@ -p $2 $(CROSSWRAP) \
|
|
$(if $3, -s $3)$(if $4, -d $4)$(if $5, -i $5) vmlinux
|
|
|
|
image-$(CONFIG_PPC_PSERIES) += zImage.pseries
|
|
image-$(CONFIG_PPC_MAPLE) += zImage.pseries
|
|
image-$(CONFIG_PPC_IBM_CELL_BLADE) += zImage.pseries
|
|
image-$(CONFIG_PPC_PS3) += dtbImage.ps3
|
|
image-$(CONFIG_PPC_CELLEB) += zImage.pseries
|
|
image-$(CONFIG_PPC_CELL_QPACE) += zImage.pseries
|
|
image-$(CONFIG_PPC_CHRP) += zImage.chrp
|
|
image-$(CONFIG_PPC_EFIKA) += zImage.chrp
|
|
image-$(CONFIG_PPC_PMAC) += zImage.pmac
|
|
image-$(CONFIG_PPC_HOLLY) += dtbImage.holly
|
|
image-$(CONFIG_PPC_PRPMC2800) += dtbImage.prpmc2800
|
|
image-$(CONFIG_PPC_ISERIES) += zImage.iseries
|
|
image-$(CONFIG_DEFAULT_UIMAGE) += uImage
|
|
|
|
#
|
|
# Targets which embed a device tree blob
|
|
#
|
|
# Theses are default targets to build images which embed device tree blobs.
|
|
# They are only required on boards which do not have FDT support in firmware.
|
|
# Boards with newish u-boot firmware can use the uImage target above
|
|
#
|
|
|
|
# Board ports in arch/powerpc/platform/40x/Kconfig
|
|
image-$(CONFIG_EP405) += dtbImage.ep405
|
|
image-$(CONFIG_HOTFOOT) += cuImage.hotfoot
|
|
image-$(CONFIG_WALNUT) += treeImage.walnut
|
|
image-$(CONFIG_ACADIA) += cuImage.acadia
|
|
|
|
# Board ports in arch/powerpc/platform/44x/Kconfig
|
|
image-$(CONFIG_EBONY) += treeImage.ebony cuImage.ebony
|
|
image-$(CONFIG_BAMBOO) += treeImage.bamboo cuImage.bamboo
|
|
image-$(CONFIG_SAM440EP) += cuImage.sam440ep
|
|
image-$(CONFIG_SEQUOIA) += cuImage.sequoia
|
|
image-$(CONFIG_RAINIER) += cuImage.rainier
|
|
image-$(CONFIG_TAISHAN) += cuImage.taishan
|
|
image-$(CONFIG_KATMAI) += cuImage.katmai
|
|
image-$(CONFIG_WARP) += cuImage.warp
|
|
image-$(CONFIG_YOSEMITE) += cuImage.yosemite
|
|
|
|
# Board ports in arch/powerpc/platform/8xx/Kconfig
|
|
image-$(CONFIG_MPC86XADS) += cuImage.mpc866ads
|
|
image-$(CONFIG_MPC885ADS) += cuImage.mpc885ads
|
|
image-$(CONFIG_PPC_EP88XC) += dtbImage.ep88xc
|
|
image-$(CONFIG_PPC_ADDER875) += cuImage.adder875-uboot \
|
|
dtbImage.adder875-redboot
|
|
|
|
# Board ports in arch/powerpc/platform/52xx/Kconfig
|
|
image-$(CONFIG_PPC_LITE5200) += cuImage.lite5200 lite5200.dtb
|
|
image-$(CONFIG_PPC_LITE5200) += cuImage.lite5200b lite5200b.dtb
|
|
image-$(CONFIG_PPC_MEDIA5200) += cuImage.media5200 media5200.dtb
|
|
|
|
# Board ports in arch/powerpc/platform/82xx/Kconfig
|
|
image-$(CONFIG_MPC8272_ADS) += cuImage.mpc8272ads
|
|
image-$(CONFIG_PQ2FADS) += cuImage.pq2fads
|
|
image-$(CONFIG_EP8248E) += dtbImage.ep8248e
|
|
|
|
# Board ports in arch/powerpc/platform/83xx/Kconfig
|
|
image-$(CONFIG_MPC832x_MDS) += cuImage.mpc832x_mds
|
|
image-$(CONFIG_MPC832x_RDB) += cuImage.mpc832x_rdb
|
|
image-$(CONFIG_MPC834x_ITX) += cuImage.mpc8349emitx \
|
|
cuImage.mpc8349emitxgp
|
|
image-$(CONFIG_MPC834x_MDS) += cuImage.mpc834x_mds
|
|
image-$(CONFIG_MPC836x_MDS) += cuImage.mpc836x_mds
|
|
image-$(CONFIG_ASP834x) += dtbImage.asp834x-redboot
|
|
|
|
# Board ports in arch/powerpc/platform/85xx/Kconfig
|
|
image-$(CONFIG_MPC8540_ADS) += cuImage.mpc8540ads
|
|
image-$(CONFIG_MPC8560_ADS) += cuImage.mpc8560ads
|
|
image-$(CONFIG_MPC85xx_CDS) += cuImage.mpc8541cds \
|
|
cuImage.mpc8548cds \
|
|
cuImage.mpc8555cds
|
|
image-$(CONFIG_MPC85xx_MDS) += cuImage.mpc8568mds
|
|
image-$(CONFIG_MPC85xx_DS) += cuImage.mpc8544ds \
|
|
cuImage.mpc8572ds
|
|
image-$(CONFIG_TQM8540) += cuImage.tqm8540
|
|
image-$(CONFIG_TQM8541) += cuImage.tqm8541
|
|
image-$(CONFIG_TQM8548) += cuImage.tqm8548
|
|
image-$(CONFIG_TQM8555) += cuImage.tqm8555
|
|
image-$(CONFIG_TQM8560) += cuImage.tqm8560
|
|
image-$(CONFIG_SBC8548) += cuImage.sbc8548
|
|
image-$(CONFIG_SBC8560) += cuImage.sbc8560
|
|
image-$(CONFIG_KSI8560) += cuImage.ksi8560
|
|
|
|
# Board ports in arch/powerpc/platform/embedded6xx/Kconfig
|
|
image-$(CONFIG_STORCENTER) += cuImage.storcenter
|
|
image-$(CONFIG_MPC7448HPC2) += cuImage.mpc7448hpc2
|
|
image-$(CONFIG_PPC_C2K) += cuImage.c2k
|
|
image-$(CONFIG_GAMECUBE) += dtbImage.gamecube
|
|
image-$(CONFIG_WII) += dtbImage.wii
|
|
|
|
# Board port in arch/powerpc/platform/amigaone/Kconfig
|
|
image-$(CONFIG_AMIGAONE) += cuImage.amigaone
|
|
|
|
# For 32-bit powermacs, build the COFF and miboot images
|
|
# as well as the ELF images.
|
|
ifeq ($(CONFIG_PPC32),y)
|
|
image-$(CONFIG_PPC_PMAC) += zImage.coff zImage.miboot
|
|
endif
|
|
|
|
# Allow extra targets to be added to the defconfig
|
|
image-y += $(subst ",,$(CONFIG_EXTRA_TARGETS))
|
|
|
|
initrd- := $(patsubst zImage%, zImage.initrd%, $(image-n) $(image-))
|
|
initrd-y := $(patsubst zImage%, zImage.initrd%, \
|
|
$(patsubst dtbImage%, dtbImage.initrd%, \
|
|
$(patsubst simpleImage%, simpleImage.initrd%, \
|
|
$(patsubst treeImage%, treeImage.initrd%, $(image-y)))))
|
|
initrd-y := $(filter-out $(image-y), $(initrd-y))
|
|
targets += $(image-y) $(initrd-y)
|
|
|
|
$(addprefix $(obj)/, $(initrd-y)): $(obj)/ramdisk.image.gz
|
|
|
|
# Don't put the ramdisk on the pattern rule; when its missing make will try
|
|
# the pattern rule with less dependencies that also matches (even with the
|
|
# hard dependency listed).
|
|
$(obj)/zImage.initrd.%: vmlinux $(wrapperbits)
|
|
$(call if_changed,wrap,$*,,,$(obj)/ramdisk.image.gz)
|
|
|
|
$(obj)/zImage.%: vmlinux $(wrapperbits)
|
|
$(call if_changed,wrap,$*)
|
|
|
|
# dtbImage% - a dtbImage is a zImage with an embedded device tree blob
|
|
$(obj)/dtbImage.initrd.%: vmlinux $(wrapperbits) $(obj)/%.dtb
|
|
$(call if_changed,wrap,$*,,$(obj)/$*.dtb,$(obj)/ramdisk.image.gz)
|
|
|
|
$(obj)/dtbImage.%: vmlinux $(wrapperbits) $(obj)/%.dtb
|
|
$(call if_changed,wrap,$*,,$(obj)/$*.dtb)
|
|
|
|
# This cannot be in the root of $(src) as the zImage rule always adds a $(obj)
|
|
# prefix
|
|
$(obj)/vmlinux.strip: vmlinux
|
|
$(STRIP) -s -R .comment $< -o $@
|
|
|
|
# The iseries hypervisor won't take an ET_DYN executable, so this
|
|
# changes the type (byte 17) in the file to ET_EXEC (2).
|
|
$(obj)/zImage.iseries: vmlinux
|
|
$(STRIP) -s -R .comment $< -o $@
|
|
printf "\x02" | dd of=$@ conv=notrunc bs=1 seek=17
|
|
|
|
$(obj)/uImage: vmlinux $(wrapperbits)
|
|
$(call if_changed,wrap,uboot)
|
|
|
|
$(obj)/cuImage.initrd.%: vmlinux $(obj)/%.dtb $(wrapperbits)
|
|
$(call if_changed,wrap,cuboot-$*,,$(obj)/$*.dtb,$(obj)/ramdisk.image.gz)
|
|
|
|
$(obj)/cuImage.%: vmlinux $(obj)/%.dtb $(wrapperbits)
|
|
$(call if_changed,wrap,cuboot-$*,,$(obj)/$*.dtb)
|
|
|
|
$(obj)/simpleImage.initrd.%: vmlinux $(obj)/%.dtb $(wrapperbits)
|
|
$(call if_changed,wrap,simpleboot-$*,,$(obj)/$*.dtb,$(obj)/ramdisk.image.gz)
|
|
|
|
$(obj)/simpleImage.%: vmlinux $(obj)/%.dtb $(wrapperbits)
|
|
$(call if_changed,wrap,simpleboot-$*,,$(obj)/$*.dtb)
|
|
|
|
$(obj)/treeImage.initrd.%: vmlinux $(obj)/%.dtb $(wrapperbits)
|
|
$(call if_changed,wrap,treeboot-$*,,$(obj)/$*.dtb,$(obj)/ramdisk.image.gz)
|
|
|
|
$(obj)/treeImage.%: vmlinux $(obj)/%.dtb $(wrapperbits)
|
|
$(call if_changed,wrap,treeboot-$*,,$(obj)/$*.dtb)
|
|
|
|
# Rule to build device tree blobs
|
|
DTC = $(objtree)/scripts/dtc/dtc
|
|
|
|
$(obj)/%.dtb: $(dtstree)/%.dts
|
|
$(DTC) -O dtb -o $(obj)/$*.dtb -b 0 $(DTS_FLAGS) $(dtstree)/$*.dts
|
|
|
|
# If there isn't a platform selected then just strip the vmlinux.
|
|
ifeq (,$(image-y))
|
|
image-y := vmlinux.strip
|
|
endif
|
|
|
|
$(obj)/zImage: $(addprefix $(obj)/, $(image-y))
|
|
@rm -f $@; ln $< $@
|
|
$(obj)/zImage.initrd: $(addprefix $(obj)/, $(initrd-y))
|
|
@rm -f $@; ln $< $@
|
|
|
|
install: $(CONFIGURE) $(addprefix $(obj)/, $(image-y))
|
|
sh -x $(srctree)/$(src)/install.sh "$(KERNELRELEASE)" vmlinux System.map "$(INSTALL_PATH)" $^
|
|
|
|
# anything not in $(targets)
|
|
clean-files += $(image-) $(initrd-) cuImage.* dtbImage.* treeImage.* \
|
|
zImage zImage.initrd zImage.chrp zImage.coff zImage.holly \
|
|
zImage.iseries zImage.miboot zImage.pmac zImage.pseries \
|
|
simpleImage.* otheros.bld *.dtb
|
|
|
|
# clean up files cached by wrapper
|
|
clean-kernel := vmlinux.strip vmlinux.bin
|
|
clean-kernel += $(addsuffix .gz,$(clean-kernel))
|
|
# If not absolute clean-files are relative to $(obj).
|
|
clean-files += $(addprefix $(objtree)/, $(clean-kernel))
|
|
|
|
WRAPPER_OBJDIR := /usr/lib/kernel-wrapper
|
|
WRAPPER_DTSDIR := /usr/lib/kernel-wrapper/dts
|
|
WRAPPER_BINDIR := /usr/sbin
|
|
INSTALL := install
|
|
|
|
extra-installed := $(patsubst $(obj)/%, $(DESTDIR)$(WRAPPER_OBJDIR)/%, $(extra-y))
|
|
hostprogs-installed := $(patsubst %, $(DESTDIR)$(WRAPPER_BINDIR)/%, $(hostprogs-y))
|
|
wrapper-installed := $(DESTDIR)$(WRAPPER_BINDIR)/wrapper
|
|
dts-installed := $(patsubst $(obj)/dts/%, $(DESTDIR)$(WRAPPER_DTSDIR)/%, $(wildcard $(obj)/dts/*.dts))
|
|
|
|
all-installed := $(extra-installed) $(hostprogs-installed) $(wrapper-installed) $(dts-installed)
|
|
|
|
quiet_cmd_mkdir = MKDIR $(patsubst $(INSTALL_HDR_PATH)/%,%,$@)
|
|
cmd_mkdir = mkdir -p $@
|
|
|
|
quiet_cmd_install = INSTALL $(patsubst $(DESTDIR)$(WRAPPER_OBJDIR)/%,%,$@)
|
|
cmd_install = $(INSTALL) -m0644 $(patsubst $(DESTDIR)$(WRAPPER_OBJDIR)/%,$(obj)/%,$@) $@
|
|
|
|
quiet_cmd_install_dts = INSTALL $(patsubst $(DESTDIR)$(WRAPPER_DTSDIR)/%,dts/%,$@)
|
|
cmd_install_dts = $(INSTALL) -m0644 $(patsubst $(DESTDIR)$(WRAPPER_DTSDIR)/%,$(srctree)/$(obj)/dts/%,$@) $@
|
|
|
|
quiet_cmd_install_exe = INSTALL $(patsubst $(DESTDIR)$(WRAPPER_BINDIR)/%,%,$@)
|
|
cmd_install_exe = $(INSTALL) -m0755 $(patsubst $(DESTDIR)$(WRAPPER_BINDIR)/%,$(obj)/%,$@) $@
|
|
|
|
quiet_cmd_install_wrapper = INSTALL $(patsubst $(DESTDIR)$(WRAPPER_BINDIR)/%,%,$@)
|
|
cmd_install_wrapper = $(INSTALL) -m0755 $(patsubst $(DESTDIR)$(WRAPPER_BINDIR)/%,$(srctree)/$(obj)/%,$@) $@ ;\
|
|
sed -i $@ -e 's%^object=.*%object=$(WRAPPER_OBJDIR)%' \
|
|
-e 's%^objbin=.*%objbin=$(WRAPPER_BINDIR)%' \
|
|
|
|
|
|
$(DESTDIR)$(WRAPPER_OBJDIR) $(DESTDIR)$(WRAPPER_DTSDIR) $(DESTDIR)$(WRAPPER_BINDIR):
|
|
$(call cmd,mkdir)
|
|
|
|
$(extra-installed) : $(DESTDIR)$(WRAPPER_OBJDIR)/% : $(obj)/% | $(DESTDIR)$(WRAPPER_OBJDIR)
|
|
$(call cmd,install)
|
|
|
|
$(hostprogs-installed) : $(DESTDIR)$(WRAPPER_BINDIR)/% : $(obj)/% | $(DESTDIR)$(WRAPPER_BINDIR)
|
|
$(call cmd,install_exe)
|
|
|
|
$(dts-installed) : $(DESTDIR)$(WRAPPER_DTSDIR)/% : $(srctree)/$(obj)/dts/% | $(DESTDIR)$(WRAPPER_DTSDIR)
|
|
$(call cmd,install_dts)
|
|
|
|
$(wrapper-installed): $(DESTDIR)$(WRAPPER_BINDIR) $(srctree)/$(obj)/wrapper | $(DESTDIR)$(WRAPPER_BINDIR)
|
|
$(call cmd,install_wrapper)
|
|
|
|
$(obj)/bootwrapper_install: $(all-installed)
|
|
|