FEX-Emu/linux
1
0
Fork 0
mirror of https://github.com/FEX-Emu/linux.git synced 2024-12-27 20:07:09 +00:00
Code Issues Actions Packages Projects Releases Wiki Activity
735d383117
linux/net/ipv4/Kconfig
Daniel Borkmann e3118e8359 net: tcp: add DCTCP congestion control algorithm 
This work adds the DataCenter TCP (DCTCP) congestion control
algorithm [1], which has been first published at SIGCOMM 2010 [2],
resp. follow-up analysis at SIGMETRICS 2011 [3] (and also, more
recently as an informational IETF draft available at [4]).

DCTCP is an enhancement to the TCP congestion control algorithm for
data center networks. Typical data center workloads are i.e.
i) partition/aggregate (queries; bursty, delay sensitive), ii) short
messages e.g. 50KB-1MB (for coordination and control state; delay
sensitive), and iii) large flows e.g. 1MB-100MB (data update;
throughput sensitive). DCTCP has therefore been designed for such
environments to provide/achieve the following three requirements:

  * High burst tolerance (incast due to partition/aggregate)
  * Low latency (short flows, queries)
  * High throughput (continuous data updates, large file
    transfers) with commodity, shallow buffered switches

The basic idea of its design consists of two fundamentals: i) on the
switch side, packets are being marked when its internal queue
length > threshold K (K is chosen so that a large enough headroom
for marked traffic is still available in the switch queue); ii) the
sender/host side maintains a moving average of the fraction of marked
packets, so each RTT, F is being updated as follows:

 F := X / Y, where X is # of marked ACKs, Y is total # of ACKs
 alpha := (1 - g) * alpha + g * F, where g is a smoothing constant

The resulting alpha (iow: probability that switch queue is congested)
is then being used in order to adaptively decrease the congestion
window W:

 W := (1 - (alpha / 2)) * W

The means for receiving marked packets resp. marking them on switch
side in DCTCP is the use of ECN.

RFC3168 describes a mechanism for using Explicit Congestion Notification
from the switch for early detection of congestion, rather than waiting
for segment loss to occur.

However, this method only detects the presence of congestion, not
the *extent*. In the presence of mild congestion, it reduces the TCP
congestion window too aggressively and unnecessarily affects the
throughput of long flows [4].

DCTCP, as mentioned, enhances Explicit Congestion Notification (ECN)
processing to estimate the fraction of bytes that encounter congestion,
rather than simply detecting that some congestion has occurred. DCTCP
then scales the TCP congestion window based on this estimate [4],
thus it can derive multibit feedback from the information present in
the single-bit sequence of marks in its control law. And thus act in
*proportion* to the extent of congestion, not its *presence*.

Switches therefore set the Congestion Experienced (CE) codepoint in
packets when internal queue lengths exceed threshold K. Resulting,
DCTCP delivers the same or better throughput than normal TCP, while
using 90% less buffer space.

It was found in [2] that DCTCP enables the applications to handle 10x
the current background traffic, without impacting foreground traffic.
Moreover, a 10x increase in foreground traffic did not cause any
timeouts, and thus largely eliminates TCP incast collapse problems.

The algorithm itself has already seen deployments in large production
data centers since then.

We did a long-term stress-test and analysis in a data center, short
summary of our TCP incast tests with iperf compared to cubic:

This test measured DCTCP throughput and latency and compared it with
CUBIC throughput and latency for an incast scenario. In this test, 19
senders sent at maximum rate to a single receiver. The receiver simply
ran iperf -s.

The senders ran iperf -c <receiver> -t 30. All senders started
simultaneously (using local clocks synchronized by ntp).

This test was repeated multiple times. Below shows the results from a
single test. Other tests are similar. (DCTCP results were extremely
consistent, CUBIC results show some variance induced by the TCP timeouts
that CUBIC encountered.)

For this test, we report statistics on the number of TCP timeouts,
flow throughput, and traffic latency.

1) Timeouts (total over all flows, and per flow summaries):

            CUBIC            DCTCP
  Total     3227             25
  Mean       169.842          1.316
  Median     183              1
  Max        207              5
  Min        123              0
  Stddev      28.991          1.600

Timeout data is taken by measuring the net change in netstat -s
"other TCP timeouts" reported. As a result, the timeout measurements
above are not restricted to the test traffic, and we believe that it
is likely that all of the "DCTCP timeouts" are actually timeouts for
non-test traffic. We report them nevertheless. CUBIC will also include
some non-test timeouts, but they are drawfed by bona fide test traffic
timeouts for CUBIC. Clearly DCTCP does an excellent job of preventing
TCP timeouts. DCTCP reduces timeouts by at least two orders of
magnitude and may well have eliminated them in this scenario.

2) Throughput (per flow in Mbps):

            CUBIC            DCTCP
  Mean      521.684          521.895
  Median    464              523
  Max       776              527
  Min       403              519
  Stddev    105.891            2.601
  Fairness    0.962            0.999

Throughput data was simply the average throughput for each flow
reported by iperf. By avoiding TCP timeouts, DCTCP is able to
achieve much better per-flow results. In CUBIC, many flows
experience TCP timeouts which makes flow throughput unpredictable and
unfair. DCTCP, on the other hand, provides very clean predictable
throughput without incurring TCP timeouts. Thus, the standard deviation
of CUBIC throughput is dramatically higher than the standard deviation
of DCTCP throughput.

Mean throughput is nearly identical because even though cubic flows
suffer TCP timeouts, other flows will step in and fill the unused
bandwidth. Note that this test is something of a best case scenario
for incast under CUBIC: it allows other flows to fill in for flows
experiencing a timeout. Under situations where the receiver is issuing
requests and then waiting for all flows to complete, flows cannot fill
in for timed out flows and throughput will drop dramatically.

3) Latency (in ms):

            CUBIC            DCTCP
  Mean      4.0088           0.04219
  Median    4.055            0.0395
  Max       4.2              0.085
  Min       3.32             0.028
  Stddev    0.1666           0.01064

Latency for each protocol was computed by running "ping -i 0.2
<receiver>" from a single sender to the receiver during the incast
test. For DCTCP, "ping -Q 0x6 -i 0.2 <receiver>" was used to ensure
that traffic traversed the DCTCP queue and was not dropped when the
queue size was greater than the marking threshold. The summary
statistics above are over all ping metrics measured between the single
sender, receiver pair.

The latency results for this test show a dramatic difference between
CUBIC and DCTCP. CUBIC intentionally overflows the switch buffer
which incurs the maximum queue latency (more buffer memory will lead
to high latency.) DCTCP, on the other hand, deliberately attempts to
keep queue occupancy low. The result is a two orders of magnitude
reduction of latency with DCTCP - even with a switch with relatively
little RAM. Switches with larger amounts of RAM will incur increasing
amounts of latency for CUBIC, but not for DCTCP.

4) Convergence and stability test:

This test measured the time that DCTCP took to fairly redistribute
bandwidth when a new flow commences. It also measured DCTCP's ability
to remain stable at a fair bandwidth distribution. DCTCP is compared
with CUBIC for this test.

At the commencement of this test, a single flow is sending at maximum
rate (near 10 Gbps) to a single receiver. One second after that first
flow commences, a new flow from a distinct server begins sending to
the same receiver as the first flow. After the second flow has sent
data for 10 seconds, the second flow is terminated. The first flow
sends for an additional second. Ideally, the bandwidth would be evenly
shared as soon as the second flow starts, and recover as soon as it
stops.

The results of this test are shown below. Note that the flow bandwidth
for the two flows was measured near the same time, but not
simultaneously.

DCTCP performs nearly perfectly within the measurement limitations
of this test: bandwidth is quickly distributed fairly between the two
flows, remains stable throughout the duration of the test, and
recovers quickly. CUBIC, in contrast, is slow to divide the bandwidth
fairly, and has trouble remaining stable.

  CUBIC                      DCTCP

  Seconds  Flow 1  Flow 2    Seconds  Flow 1  Flow 2
   0       9.93    0          0       9.92    0
   0.5     9.87    0          0.5     9.86    0
   1       8.73    2.25       1       6.46    4.88
   1.5     7.29    2.8        1.5     4.9     4.99
   2       6.96    3.1        2       4.92    4.94
   2.5     6.67    3.34       2.5     4.93    5
   3       6.39    3.57       3       4.92    4.99
   3.5     6.24    3.75       3.5     4.94    4.74
   4       6       3.94       4       5.34    4.71
   4.5     5.88    4.09       4.5     4.99    4.97
   5       5.27    4.98       5       4.83    5.01
   5.5     4.93    5.04       5.5     4.89    4.99
   6       4.9     4.99       6       4.92    5.04
   6.5     4.93    5.1        6.5     4.91    4.97
   7       4.28    5.8        7       4.97    4.97
   7.5     4.62    4.91       7.5     4.99    4.82
   8       5.05    4.45       8       5.16    4.76
   8.5     5.93    4.09       8.5     4.94    4.98
   9       5.73    4.2        9       4.92    5.02
   9.5     5.62    4.32       9.5     4.87    5.03
  10       6.12    3.2       10       4.91    5.01
  10.5     6.91    3.11      10.5     4.87    5.04
  11       8.48    0         11       8.49    4.94
  11.5     9.87    0         11.5     9.9     0

SYN/ACK ECT test:

This test demonstrates the importance of ECT on SYN and SYN-ACK packets
by measuring the connection probability in the presence of competing
flows for a DCTCP connection attempt *without* ECT in the SYN packet.
The test was repeated five times for each number of competing flows.

              Competing Flows  1 |    2 |    4 |    8 |   16
                               ------------------------------
Mean Connection Probability    1 | 0.67 | 0.45 | 0.28 |    0
Median Connection Probability  1 | 0.65 | 0.45 | 0.25 |    0

As the number of competing flows moves beyond 1, the connection
probability drops rapidly.

Enabling DCTCP with this patch requires the following steps:

DCTCP must be running both on the sender and receiver side in your
data center, i.e.:

  sysctl -w net.ipv4.tcp_congestion_control=dctcp

Also, ECN functionality must be enabled on all switches in your
data center for DCTCP to work. The default ECN marking threshold (K)
heuristic on the switch for DCTCP is e.g., 20 packets (30KB) at
1Gbps, and 65 packets (~100KB) at 10Gbps (K > 1/7 * C * RTT, [4]).

In above tests, for each switch port, traffic was segregated into two
queues. For any packet with a DSCP of 0x01 - or equivalently a TOS of
0x04 - the packet was placed into the DCTCP queue. All other packets
were placed into the default drop-tail queue. For the DCTCP queue,
RED/ECN marking was enabled, here, with a marking threshold of 75 KB.
More details however, we refer you to the paper [2] under section 3).

There are no code changes required to applications running in user
space. DCTCP has been implemented in full *isolation* of the rest of
the TCP code as its own congestion control module, so that it can run
without a need to expose code to the core of the TCP stack, and thus
nothing changes for non-DCTCP users.

Changes in the CA framework code are minimal, and DCTCP algorithm
operates on mechanisms that are already available in most Silicon.
The gain (dctcp_shift_g) is currently a fixed constant (1/16) from
the paper, but we leave the option that it can be chosen carefully
to a different value by the user.

In case DCTCP is being used and ECN support on peer site is off,
DCTCP falls back after 3WHS to operate in normal TCP Reno mode.

ss {-4,-6} -t -i diag interface:

  ... dctcp wscale:7,7 rto:203 rtt:2.349/0.026 mss:1448 cwnd:2054
  ssthresh:1102 ce_state 0 alpha 15 ab_ecn 0 ab_tot 735584
  send 10129.2Mbps pacing_rate 20254.1Mbps unacked:1822 retrans:0/15
  reordering:101 rcv_space:29200

  ... dctcp-reno wscale:7,7 rto:201 rtt:0.711/1.327 ato:40 mss:1448
  cwnd:10 ssthresh:1102 fallback_mode send 162.9Mbps pacing_rate
  325.5Mbps rcv_rtt:1.5 rcv_space:29200

More information about DCTCP can be found in [1-4].

  [1] http://simula.stanford.edu/~alizade/Site/DCTCP.html
  [2] http://simula.stanford.edu/~alizade/Site/DCTCP_files/dctcp-final.pdf
  [3] http://simula.stanford.edu/~alizade/Site/DCTCP_files/dctcp_analysis-full.pdf
  [4] http://tools.ietf.org/html/draft-bensley-tcpm-dctcp-00

Joint work with Florian Westphal and Glenn Judd.

Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Glenn Judd <glenn.judd@morganstanley.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-29 00:13:10 -04:00

659 lines
22 KiB
Plaintext
Raw Blame History

#
# IP configuration
#
config IP_MULTICAST
bool "IP: multicasting"
help
This is code for addressing several networked computers at once,
enlarging your kernel by about 2 KB. You need multicasting if you
intend to participate in the MBONE, a high bandwidth network on top
of the Internet which carries audio and video broadcasts. More
information about the MBONE is on the WWW at
<http://www.savetz.com/mbone/>. For most people, it's safe to say N.
config IP_ADVANCED_ROUTER
bool "IP: advanced router"
---help---
If you intend to run your Linux box mostly as a router, i.e. as a
computer that forwards and redistributes network packets, say Y; you
will then be presented with several options that allow more precise
control about the routing process.
The answer to this question won't directly affect the kernel:
answering N will just cause the configurator to skip all the
questions about advanced routing.
Note that your box can only act as a router if you enable IP
forwarding in your kernel; you can do that by saying Y to "/proc
file system support" and "Sysctl support" below and executing the
line
echo "1" > /proc/sys/net/ipv4/ip_forward
at boot time after the /proc file system has been mounted.
If you turn on IP forwarding, you should consider the rp_filter, which
automatically rejects incoming packets if the routing table entry
for their source address doesn't match the network interface they're
arriving on. This has security advantages because it prevents the
so-called IP spoofing, however it can pose problems if you use
asymmetric routing (packets from you to a host take a different path
than packets from that host to you) or if you operate a non-routing
host which has several IP addresses on different interfaces. To turn
rp_filter on use:
echo 1 > /proc/sys/net/ipv4/conf/<device>/rp_filter
or
echo 1 > /proc/sys/net/ipv4/conf/all/rp_filter
Note that some distributions enable it in startup scripts.
For details about rp_filter strict and loose mode read
<file:Documentation/networking/ip-sysctl.txt>.
If unsure, say N here.
config IP_FIB_TRIE_STATS
bool "FIB TRIE statistics"
depends on IP_ADVANCED_ROUTER
---help---
Keep track of statistics on structure of FIB TRIE table.
Useful for testing and measuring TRIE performance.
config IP_MULTIPLE_TABLES
bool "IP: policy routing"
depends on IP_ADVANCED_ROUTER
select FIB_RULES
---help---
Normally, a router decides what to do with a received packet based
solely on the packet's final destination address. If you say Y here,
the Linux router will also be able to take the packet's source
address into account. Furthermore, the TOS (Type-Of-Service) field
of the packet can be used for routing decisions as well.
If you are interested in this, please see the preliminary
documentation at <http://www.compendium.com.ar/policy-routing.txt>
and <ftp://post.tepkom.ru/pub/vol2/Linux/docs/advanced-routing.tex>.
You will need supporting software from
<ftp://ftp.tux.org/pub/net/ip-routing/>.
If unsure, say N.
config IP_ROUTE_MULTIPATH
bool "IP: equal cost multipath"
depends on IP_ADVANCED_ROUTER
help
Normally, the routing tables specify a single action to be taken in
a deterministic manner for a given packet. If you say Y here
however, it becomes possible to attach several actions to a packet
pattern, in effect specifying several alternative paths to travel
for those packets. The router considers all these paths to be of
equal "cost" and chooses one of them in a non-deterministic fashion
if a matching packet arrives.
config IP_ROUTE_VERBOSE
bool "IP: verbose route monitoring"
depends on IP_ADVANCED_ROUTER
help
If you say Y here, which is recommended, then the kernel will print
verbose messages regarding the routing, for example warnings about
received packets which look strange and could be evidence of an
attack or a misconfigured system somewhere. The information is
handled by the klogd daemon which is responsible for kernel messages
("man klogd").
config IP_ROUTE_CLASSID
bool
config IP_PNP
bool "IP: kernel level autoconfiguration"
help
This enables automatic configuration of IP addresses of devices and
of the routing table during kernel boot, based on either information
supplied on the kernel command line or by BOOTP or RARP protocols.
You need to say Y only for diskless machines requiring network
access to boot (in which case you want to say Y to "Root file system
on NFS" as well), because all other machines configure the network
in their startup scripts.
config IP_PNP_DHCP
bool "IP: DHCP support"
depends on IP_PNP
---help---
If you want your Linux box to mount its whole root file system (the
one containing the directory /) from some other computer over the
net via NFS and you want the IP address of your computer to be
discovered automatically at boot time using the DHCP protocol (a
special protocol designed for doing this job), say Y here. In case
the boot ROM of your network card was designed for booting Linux and
does DHCP itself, providing all necessary information on the kernel
command line, you can say N here.
If unsure, say Y. Note that if you want to use DHCP, a DHCP server
must be operating on your network. Read
<file:Documentation/filesystems/nfs/nfsroot.txt> for details.
config IP_PNP_BOOTP
bool "IP: BOOTP support"
depends on IP_PNP
---help---
If you want your Linux box to mount its whole root file system (the
one containing the directory /) from some other computer over the
net via NFS and you want the IP address of your computer to be
discovered automatically at boot time using the BOOTP protocol (a
special protocol designed for doing this job), say Y here. In case
the boot ROM of your network card was designed for booting Linux and
does BOOTP itself, providing all necessary information on the kernel
command line, you can say N here. If unsure, say Y. Note that if you
want to use BOOTP, a BOOTP server must be operating on your network.
Read <file:Documentation/filesystems/nfs/nfsroot.txt> for details.
config IP_PNP_RARP
bool "IP: RARP support"
depends on IP_PNP
help
If you want your Linux box to mount its whole root file system (the
one containing the directory /) from some other computer over the
net via NFS and you want the IP address of your computer to be
discovered automatically at boot time using the RARP protocol (an
older protocol which is being obsoleted by BOOTP and DHCP), say Y
here. Note that if you want to use RARP, a RARP server must be
operating on your network. Read
<file:Documentation/filesystems/nfs/nfsroot.txt> for details.
config NET_IPIP
tristate "IP: tunneling"
select INET_TUNNEL
select NET_IP_TUNNEL
---help---
Tunneling means encapsulating data of one protocol type within
another protocol and sending it over a channel that understands the
encapsulating protocol. This particular tunneling driver implements
encapsulation of IP within IP, which sounds kind of pointless, but
can be useful if you want to make your (or some other) machine
appear on a different network than it physically is, or to use
mobile-IP facilities (allowing laptops to seamlessly move between
networks without changing their IP addresses).
Saying Y to this option will produce two modules ( = code which can
be inserted in and removed from the running kernel whenever you
want). Most people won't need this and can say N.
config NET_IPGRE_DEMUX
tristate "IP: GRE demultiplexer"
help
This is helper module to demultiplex GRE packets on GRE version field criteria.
Required by ip_gre and pptp modules.
config NET_IP_TUNNEL
tristate
default n
config NET_IPGRE
tristate "IP: GRE tunnels over IP"
depends on (IPV6 || IPV6=n) && NET_IPGRE_DEMUX
select NET_IP_TUNNEL
help
Tunneling means encapsulating data of one protocol type within
another protocol and sending it over a channel that understands the
encapsulating protocol. This particular tunneling driver implements
GRE (Generic Routing Encapsulation) and at this time allows
encapsulating of IPv4 or IPv6 over existing IPv4 infrastructure.
This driver is useful if the other endpoint is a Cisco router: Cisco
likes GRE much better than the other Linux tunneling driver ("IP
tunneling" above). In addition, GRE allows multicast redistribution
through the tunnel.
config NET_IPGRE_BROADCAST
bool "IP: broadcast GRE over IP"
depends on IP_MULTICAST && NET_IPGRE
help
One application of GRE/IP is to construct a broadcast WAN (Wide Area
Network), which looks like a normal Ethernet LAN (Local Area
Network), but can be distributed all over the Internet. If you want
to do that, say Y here and to "IP multicast routing" below.
config IP_MROUTE
bool "IP: multicast routing"
depends on IP_MULTICAST
help
This is used if you want your machine to act as a router for IP
packets that have several destination addresses. It is needed on the
MBONE, a high bandwidth network on top of the Internet which carries
audio and video broadcasts. In order to do that, you would most
likely run the program mrouted. If you haven't heard about it, you
don't need it.
config IP_MROUTE_MULTIPLE_TABLES
bool "IP: multicast policy routing"
depends on IP_MROUTE && IP_ADVANCED_ROUTER
select FIB_RULES
help
Normally, a multicast router runs a userspace daemon and decides
what to do with a multicast packet based on the source and
destination addresses. If you say Y here, the multicast router
will also be able to take interfaces and packet marks into
account and run multiple instances of userspace daemons
simultaneously, each one handling a single table.
If unsure, say N.
config IP_PIMSM_V1
bool "IP: PIM-SM version 1 support"
depends on IP_MROUTE
help
Kernel side support for Sparse Mode PIM (Protocol Independent
Multicast) version 1. This multicast routing protocol is used widely
because Cisco supports it. You need special software to use it
(pimd-v1). Please see <http://netweb.usc.edu/pim/> for more
information about PIM.
Say Y if you want to use PIM-SM v1. Note that you can say N here if
you just want to use Dense Mode PIM.
config IP_PIMSM_V2
bool "IP: PIM-SM version 2 support"
depends on IP_MROUTE
help
Kernel side support for Sparse Mode PIM version 2. In order to use
this, you need an experimental routing daemon supporting it (pimd or
gated-5). This routing protocol is not used widely, so say N unless
you want to play with it.
config SYN_COOKIES
bool "IP: TCP syncookie support"
---help---
Normal TCP/IP networking is open to an attack known as "SYN
flooding". This denial-of-service attack prevents legitimate remote
users from being able to connect to your computer during an ongoing
attack and requires very little work from the attacker, who can
operate from anywhere on the Internet.
SYN cookies provide protection against this type of attack. If you
say Y here, the TCP/IP stack will use a cryptographic challenge
protocol known as "SYN cookies" to enable legitimate users to
continue to connect, even when your machine is under attack. There
is no need for the legitimate users to change their TCP/IP software;
SYN cookies work transparently to them. For technical information
about SYN cookies, check out <http://cr.yp.to/syncookies.html>.
If you are SYN flooded, the source address reported by the kernel is
likely to have been forged by the attacker; it is only reported as
an aid in tracing the packets to their actual source and should not
be taken as absolute truth.
SYN cookies may prevent correct error reporting on clients when the
server is really overloaded. If this happens frequently better turn
them off.
If you say Y here, you can disable SYN cookies at run time by
saying Y to "/proc file system support" and
"Sysctl support" below and executing the command
echo 0 > /proc/sys/net/ipv4/tcp_syncookies
after the /proc file system has been mounted.
If unsure, say N.
config NET_IPVTI
tristate "Virtual (secure) IP: tunneling"
select INET_TUNNEL
select NET_IP_TUNNEL
depends on INET_XFRM_MODE_TUNNEL
---help---
Tunneling means encapsulating data of one protocol type within
another protocol and sending it over a channel that understands the
encapsulating protocol. This can be used with xfrm mode tunnel to give
the notion of a secure tunnel for IPSEC and then use routing protocol
on top.
config NET_UDP_TUNNEL
tristate
default n
config NET_FOU
tristate "IP: Foo (IP protocols) over UDP"
select XFRM
select NET_UDP_TUNNEL
---help---
Foo over UDP allows any IP protocol to be directly encapsulated
over UDP include tunnels (IPIP, GRE, SIT). By encapsulating in UDP
network mechanisms and optimizations for UDP (such as ECMP
and RSS) can be leveraged to provide better service.
config INET_AH
tristate "IP: AH transformation"
select XFRM_ALGO
select CRYPTO
select CRYPTO_HMAC
select CRYPTO_MD5
select CRYPTO_SHA1
---help---
Support for IPsec AH.
If unsure, say Y.
config INET_ESP
tristate "IP: ESP transformation"
select XFRM_ALGO
select CRYPTO
select CRYPTO_AUTHENC
select CRYPTO_HMAC
select CRYPTO_MD5
select CRYPTO_CBC
select CRYPTO_SHA1
select CRYPTO_DES
---help---
Support for IPsec ESP.
If unsure, say Y.
config INET_IPCOMP
tristate "IP: IPComp transformation"
select INET_XFRM_TUNNEL
select XFRM_IPCOMP
---help---
Support for IP Payload Compression Protocol (IPComp) (RFC3173),
typically needed for IPsec.
If unsure, say Y.
config INET_XFRM_TUNNEL
tristate
select INET_TUNNEL
default n
config INET_TUNNEL
tristate
default n
config INET_XFRM_MODE_TRANSPORT
tristate "IP: IPsec transport mode"
default y
select XFRM
---help---
Support for IPsec transport mode.
If unsure, say Y.
config INET_XFRM_MODE_TUNNEL
tristate "IP: IPsec tunnel mode"
default y
select XFRM
---help---
Support for IPsec tunnel mode.
If unsure, say Y.
config INET_XFRM_MODE_BEET
tristate "IP: IPsec BEET mode"
default y
select XFRM
---help---
Support for IPsec BEET mode.
If unsure, say Y.
config INET_LRO
tristate "Large Receive Offload (ipv4/tcp)"
default y
---help---
Support for Large Receive Offload (ipv4/tcp).
If unsure, say Y.
config INET_DIAG
tristate "INET: socket monitoring interface"
default y
---help---
Support for INET (TCP, DCCP, etc) socket monitoring interface used by
native Linux tools such as ss. ss is included in iproute2, currently
downloadable at:
http://www.linuxfoundation.org/collaborate/workgroups/networking/iproute2
If unsure, say Y.
config INET_TCP_DIAG
depends on INET_DIAG
def_tristate INET_DIAG
config INET_UDP_DIAG
tristate "UDP: socket monitoring interface"
depends on INET_DIAG && (IPV6 || IPV6=n)
default n
---help---
Support for UDP socket monitoring interface used by the ss tool.
If unsure, say Y.
menuconfig TCP_CONG_ADVANCED
bool "TCP: advanced congestion control"
---help---
Support for selection of various TCP congestion control
modules.
Nearly all users can safely say no here, and a safe default
selection will be made (CUBIC with new Reno as a fallback).
If unsure, say N.
if TCP_CONG_ADVANCED
config TCP_CONG_BIC
tristate "Binary Increase Congestion (BIC) control"
default m
---help---
BIC-TCP is a sender-side only change that ensures a linear RTT
fairness under large windows while offering both scalability and
bounded TCP-friendliness. The protocol combines two schemes
called additive increase and binary search increase. When the
congestion window is large, additive increase with a large
increment ensures linear RTT fairness as well as good
scalability. Under small congestion windows, binary search
increase provides TCP friendliness.
See http://www.csc.ncsu.edu/faculty/rhee/export/bitcp/
config TCP_CONG_CUBIC
tristate "CUBIC TCP"
default y
---help---
This is version 2.0 of BIC-TCP which uses a cubic growth function
among other techniques.
See http://www.csc.ncsu.edu/faculty/rhee/export/bitcp/cubic-paper.pdf
config TCP_CONG_WESTWOOD
tristate "TCP Westwood+"
default m
---help---
TCP Westwood+ is a sender-side only modification of the TCP Reno
protocol stack that optimizes the performance of TCP congestion
control. It is based on end-to-end bandwidth estimation to set
congestion window and slow start threshold after a congestion
episode. Using this estimation, TCP Westwood+ adaptively sets a
slow start threshold and a congestion window which takes into
account the bandwidth used at the time congestion is experienced.
TCP Westwood+ significantly increases fairness wrt TCP Reno in
wired networks and throughput over wireless links.
config TCP_CONG_HTCP
tristate "H-TCP"
default m
---help---
H-TCP is a send-side only modifications of the TCP Reno
protocol stack that optimizes the performance of TCP
congestion control for high speed network links. It uses a
modeswitch to change the alpha and beta parameters of TCP Reno
based on network conditions and in a way so as to be fair with
other Reno and H-TCP flows.
config TCP_CONG_HSTCP
tristate "High Speed TCP"
default n
---help---
Sally Floyd's High Speed TCP (RFC 3649) congestion control.
A modification to TCP's congestion control mechanism for use
with large congestion windows. A table indicates how much to
increase the congestion window by when an ACK is received.
For more detail see http://www.icir.org/floyd/hstcp.html
config TCP_CONG_HYBLA
tristate "TCP-Hybla congestion control algorithm"
default n
---help---
TCP-Hybla is a sender-side only change that eliminates penalization of
long-RTT, large-bandwidth connections, like when satellite legs are
involved, especially when sharing a common bottleneck with normal
terrestrial connections.
config TCP_CONG_VEGAS
tristate "TCP Vegas"
default n
---help---
TCP Vegas is a sender-side only change to TCP that anticipates
the onset of congestion by estimating the bandwidth. TCP Vegas
adjusts the sending rate by modifying the congestion
window. TCP Vegas should provide less packet loss, but it is
not as aggressive as TCP Reno.
config TCP_CONG_SCALABLE
tristate "Scalable TCP"
default n
---help---
Scalable TCP is a sender-side only change to TCP which uses a
MIMD congestion control algorithm which has some nice scaling
properties, though is known to have fairness issues.
See http://www.deneholme.net/tom/scalable/
config TCP_CONG_LP
tristate "TCP Low Priority"
default n
---help---
TCP Low Priority (TCP-LP), a distributed algorithm whose goal is
to utilize only the excess network bandwidth as compared to the
``fair share`` of bandwidth as targeted by TCP.
See http://www-ece.rice.edu/networks/TCP-LP/
config TCP_CONG_VENO
tristate "TCP Veno"
default n
---help---
TCP Veno is a sender-side only enhancement of TCP to obtain better
throughput over wireless networks. TCP Veno makes use of state
distinguishing to circumvent the difficult judgment of the packet loss
type. TCP Veno cuts down less congestion window in response to random
loss packets.
See <http://ieeexplore.ieee.org/xpl/freeabs_all.jsp?arnumber=1177186>
config TCP_CONG_YEAH
tristate "YeAH TCP"
select TCP_CONG_VEGAS
default n
---help---
YeAH-TCP is a sender-side high-speed enabled TCP congestion control
algorithm, which uses a mixed loss/delay approach to compute the
congestion window. It's design goals target high efficiency,
internal, RTT and Reno fairness, resilience to link loss while
keeping network elements load as low as possible.
For further details look here:
http://wil.cs.caltech.edu/pfldnet2007/paper/YeAH_TCP.pdf
config TCP_CONG_ILLINOIS
tristate "TCP Illinois"
default n
---help---
TCP-Illinois is a sender-side modification of TCP Reno for
high speed long delay links. It uses round-trip-time to
adjust the alpha and beta parameters to achieve a higher average
throughput and maintain fairness.
For further details see:
http://www.ews.uiuc.edu/~shaoliu/tcpillinois/index.html
config TCP_CONG_DCTCP
tristate "DataCenter TCP (DCTCP)"
default n
---help---
DCTCP leverages Explicit Congestion Notification (ECN) in the network to
provide multi-bit feedback to the end hosts. It is designed to provide:
- High burst tolerance (incast due to partition/aggregate),
- Low latency (short flows, queries),
- High throughput (continuous data updates, large file transfers) with
commodity, shallow-buffered switches.
All switches in the data center network running DCTCP must support
ECN marking and be configured for marking when reaching defined switch
buffer thresholds. The default ECN marking threshold heuristic for
DCTCP on switches is 20 packets (30KB) at 1Gbps, and 65 packets
(~100KB) at 10Gbps, but might need further careful tweaking.
For further details see:
http://simula.stanford.edu/~alizade/Site/DCTCP_files/dctcp-final.pdf
choice
prompt "Default TCP congestion control"
default DEFAULT_CUBIC
help
Select the TCP congestion control that will be used by default
for all connections.
config DEFAULT_BIC
bool "Bic" if TCP_CONG_BIC=y
config DEFAULT_CUBIC
bool "Cubic" if TCP_CONG_CUBIC=y
config DEFAULT_HTCP
bool "Htcp" if TCP_CONG_HTCP=y
config DEFAULT_HYBLA
bool "Hybla" if TCP_CONG_HYBLA=y
config DEFAULT_VEGAS
bool "Vegas" if TCP_CONG_VEGAS=y
config DEFAULT_VENO
bool "Veno" if TCP_CONG_VENO=y
config DEFAULT_WESTWOOD
bool "Westwood" if TCP_CONG_WESTWOOD=y
config DEFAULT_DCTCP
bool "DCTCP" if TCP_CONG_DCTCP=y
config DEFAULT_RENO
bool "Reno"
endchoice
endif
config TCP_CONG_CUBIC
tristate
depends on !TCP_CONG_ADVANCED
default y
config DEFAULT_TCP_CONG
string
default "bic" if DEFAULT_BIC
default "cubic" if DEFAULT_CUBIC
default "htcp" if DEFAULT_HTCP
default "hybla" if DEFAULT_HYBLA
default "vegas" if DEFAULT_VEGAS
default "westwood" if DEFAULT_WESTWOOD
default "veno" if DEFAULT_VENO
default "reno" if DEFAULT_RENO
default "dctcp" if DEFAULT_DCTCP
default "cubic"
config TCP_MD5SIG
bool "TCP: MD5 Signature Option support (RFC2385)"
select CRYPTO
select CRYPTO_MD5
---help---
RFC2385 specifies a method of giving MD5 protection to TCP sessions.
Its main (only?) use is to protect BGP sessions between core routers
on the Internet.
If unsure, say N.
Reference in New Issue View Git Blame Copy Permalink