mirror of
https://github.com/FEX-Emu/linux.git
synced 2024-12-27 20:07:09 +00:00
bdfca5025a
xHCI 1.0 spec specifies the xHC shall halt within 16ms after software clears Run/Stop bit. In xHCI 0.96 spec the time limit is 16 microframes (2ms), it's too short and often cause dmesg shows "Host controller not halted, aborting reset." message when rmmod xhci-hcd. Modify the time limit to comply with xHCI 1.0 specification and prevents the warning message showing when remove xhci-hcd. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
149 lines
5.0 KiB
C
149 lines
5.0 KiB
C
/*
|
|
* xHCI host controller driver
|
|
*
|
|
* Copyright (C) 2008 Intel Corp.
|
|
*
|
|
* Author: Sarah Sharp
|
|
* Some code borrowed from the Linux EHCI driver.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful, but
|
|
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
|
|
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
|
|
* for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software Foundation,
|
|
* Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
*/
|
|
/* Up to 16 ms to halt an HC */
|
|
#define XHCI_MAX_HALT_USEC (16*1000)
|
|
/* HC not running - set to 1 when run/stop bit is cleared. */
|
|
#define XHCI_STS_HALT (1<<0)
|
|
|
|
/* HCCPARAMS offset from PCI base address */
|
|
#define XHCI_HCC_PARAMS_OFFSET 0x10
|
|
/* HCCPARAMS contains the first extended capability pointer */
|
|
#define XHCI_HCC_EXT_CAPS(p) (((p)>>16)&0xffff)
|
|
|
|
/* Command and Status registers offset from the Operational Registers address */
|
|
#define XHCI_CMD_OFFSET 0x00
|
|
#define XHCI_STS_OFFSET 0x04
|
|
|
|
#define XHCI_MAX_EXT_CAPS 50
|
|
|
|
/* Capability Register */
|
|
/* bits 7:0 - how long is the Capabilities register */
|
|
#define XHCI_HC_LENGTH(p) (((p)>>00)&0x00ff)
|
|
|
|
/* Extended capability register fields */
|
|
#define XHCI_EXT_CAPS_ID(p) (((p)>>0)&0xff)
|
|
#define XHCI_EXT_CAPS_NEXT(p) (((p)>>8)&0xff)
|
|
#define XHCI_EXT_CAPS_VAL(p) ((p)>>16)
|
|
/* Extended capability IDs - ID 0 reserved */
|
|
#define XHCI_EXT_CAPS_LEGACY 1
|
|
#define XHCI_EXT_CAPS_PROTOCOL 2
|
|
#define XHCI_EXT_CAPS_PM 3
|
|
#define XHCI_EXT_CAPS_VIRT 4
|
|
#define XHCI_EXT_CAPS_ROUTE 5
|
|
/* IDs 6-9 reserved */
|
|
#define XHCI_EXT_CAPS_DEBUG 10
|
|
/* USB Legacy Support Capability - section 7.1.1 */
|
|
#define XHCI_HC_BIOS_OWNED (1 << 16)
|
|
#define XHCI_HC_OS_OWNED (1 << 24)
|
|
|
|
/* USB Legacy Support Capability - section 7.1.1 */
|
|
/* Add this offset, plus the value of xECP in HCCPARAMS to the base address */
|
|
#define XHCI_LEGACY_SUPPORT_OFFSET (0x00)
|
|
|
|
/* USB Legacy Support Control and Status Register - section 7.1.2 */
|
|
/* Add this offset, plus the value of xECP in HCCPARAMS to the base address */
|
|
#define XHCI_LEGACY_CONTROL_OFFSET (0x04)
|
|
/* bits 1:2, 5:12, and 17:19 need to be preserved; bits 21:28 should be zero */
|
|
#define XHCI_LEGACY_DISABLE_SMI ((0x3 << 1) + (0xff << 5) + (0x7 << 17))
|
|
|
|
/* command register values to disable interrupts and halt the HC */
|
|
/* start/stop HC execution - do not write unless HC is halted*/
|
|
#define XHCI_CMD_RUN (1 << 0)
|
|
/* Event Interrupt Enable - get irq when EINT bit is set in USBSTS register */
|
|
#define XHCI_CMD_EIE (1 << 2)
|
|
/* Host System Error Interrupt Enable - get irq when HSEIE bit set in USBSTS */
|
|
#define XHCI_CMD_HSEIE (1 << 3)
|
|
/* Enable Wrap Event - '1' means xHC generates an event when MFINDEX wraps. */
|
|
#define XHCI_CMD_EWE (1 << 10)
|
|
|
|
#define XHCI_IRQS (XHCI_CMD_EIE | XHCI_CMD_HSEIE | XHCI_CMD_EWE)
|
|
|
|
/* true: Controller Not Ready to accept doorbell or op reg writes after reset */
|
|
#define XHCI_STS_CNR (1 << 11)
|
|
|
|
#include <linux/io.h>
|
|
|
|
/**
|
|
* Return the next extended capability pointer register.
|
|
*
|
|
* @base PCI register base address.
|
|
*
|
|
* @ext_offset Offset of the 32-bit register that contains the extended
|
|
* capabilites pointer. If searching for the first extended capability, pass
|
|
* in XHCI_HCC_PARAMS_OFFSET. If searching for the next extended capability,
|
|
* pass in the offset of the current extended capability register.
|
|
*
|
|
* Returns 0 if there is no next extended capability register or returns the register offset
|
|
* from the PCI registers base address.
|
|
*/
|
|
static inline int xhci_find_next_cap_offset(void __iomem *base, int ext_offset)
|
|
{
|
|
u32 next;
|
|
|
|
next = readl(base + ext_offset);
|
|
|
|
if (ext_offset == XHCI_HCC_PARAMS_OFFSET) {
|
|
/* Find the first extended capability */
|
|
next = XHCI_HCC_EXT_CAPS(next);
|
|
ext_offset = 0;
|
|
} else {
|
|
/* Find the next extended capability */
|
|
next = XHCI_EXT_CAPS_NEXT(next);
|
|
}
|
|
|
|
if (!next)
|
|
return 0;
|
|
/*
|
|
* Address calculation from offset of extended capabilities
|
|
* (or HCCPARAMS) register - see section 5.3.6 and section 7.
|
|
*/
|
|
return ext_offset + (next << 2);
|
|
}
|
|
|
|
/**
|
|
* Find the offset of the extended capabilities with capability ID id.
|
|
*
|
|
* @base PCI MMIO registers base address.
|
|
* @ext_offset Offset from base of the first extended capability to look at,
|
|
* or the address of HCCPARAMS.
|
|
* @id Extended capability ID to search for.
|
|
*
|
|
* This uses an arbitrary limit of XHCI_MAX_EXT_CAPS extended capabilities
|
|
* to make sure that the list doesn't contain a loop.
|
|
*/
|
|
static inline int xhci_find_ext_cap_by_id(void __iomem *base, int ext_offset, int id)
|
|
{
|
|
u32 val;
|
|
int limit = XHCI_MAX_EXT_CAPS;
|
|
|
|
while (ext_offset && limit > 0) {
|
|
val = readl(base + ext_offset);
|
|
if (XHCI_EXT_CAPS_ID(val) == id)
|
|
break;
|
|
ext_offset = xhci_find_next_cap_offset(base, ext_offset);
|
|
limit--;
|
|
}
|
|
if (limit > 0)
|
|
return ext_offset;
|
|
return 0;
|
|
}
|