mirror of
https://github.com/FEX-Emu/linux.git
synced 2024-12-15 21:30:43 +00:00
1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
163 lines
4.4 KiB
ArmAsm
163 lines
4.4 KiB
ArmAsm
@ Read/Write DMA code for the ST506/MFM hard drive controllers on the A400 Acorn Archimedes
|
|
@ motherboard and on ST506 expansion podules.
|
|
@ (c) David Alan Gilbert (linux@treblig.org) 1996-1999
|
|
|
|
#include <asm/assembler.h>
|
|
|
|
hdc63463_irqdata:
|
|
@ Controller base address
|
|
.global hdc63463_baseaddress
|
|
hdc63463_baseaddress:
|
|
.word 0
|
|
|
|
.global hdc63463_irqpolladdress
|
|
hdc63463_irqpolladdress:
|
|
.word 0
|
|
|
|
.global hdc63463_irqpollmask
|
|
hdc63463_irqpollmask:
|
|
.word 0
|
|
|
|
@ where to read/write data from the kernel data space
|
|
.global hdc63463_dataptr
|
|
hdc63463_dataptr:
|
|
.word 0
|
|
|
|
@ Number of bytes left to transfer
|
|
.global hdc63463_dataleft
|
|
hdc63463_dataleft:
|
|
.word 0
|
|
|
|
@ -------------------------------------------------------------------------
|
|
@ hdc63463_writedma: DMA from host to controller
|
|
@ internal reg usage: r0=hdc base address, r1=irq poll address, r2=poll mask
|
|
@ r3=data ptr, r4=data left, r5,r6=temporary
|
|
.global hdc63463_writedma
|
|
hdc63463_writedma:
|
|
stmfd sp!,{r4-r7}
|
|
adr r5,hdc63463_irqdata
|
|
ldmia r5,{r0,r1,r2,r3,r4}
|
|
|
|
writedma_again:
|
|
|
|
@ test number of remaining bytes to transfer
|
|
cmp r4,#0
|
|
beq writedma_end
|
|
bmi writedma_end
|
|
|
|
@ Check the hdc is interrupting
|
|
ldrb r5,[r1,#0]
|
|
tst r5,r2
|
|
beq writedma_end
|
|
|
|
@ Transfer a block of upto 256 bytes
|
|
cmp r4,#256
|
|
movlt r7,r4
|
|
movge r7,#256
|
|
|
|
@ Check the hdc is still busy and command has not ended and no errors
|
|
ldr r5,[r0,#32] @ Status reg - 16 bit - its the top few bits which are status
|
|
@ think we should continue DMA until it drops busy - perhaps this was
|
|
@ the main problem with corrected errors causing a hang
|
|
@tst r5,#0x3c00 @ Test for things which should be off
|
|
@bne writedma_end
|
|
and r5,r5,#0x8000 @ This is test for things which should be on: Busy
|
|
cmp r5,#0x8000
|
|
bne writedma_end
|
|
|
|
@ Bytes remaining at end
|
|
sub r4,r4,r7
|
|
|
|
@ HDC Write register location
|
|
add r0,r0,#32+8
|
|
|
|
writedma_loop:
|
|
@ OK - pretty sure we should be doing this
|
|
|
|
ldr r5,[r3],#4 @ Get a word to be written
|
|
@ get bottom half to be sent first
|
|
mov r6,r5,lsl#16 @ Separate the first 2 bytes
|
|
orr r2,r6,r6,lsr #16 @ Duplicate them in the bottom half of the word
|
|
@ now the top half
|
|
mov r6,r5,lsr#16 @ Get 2nd 2 bytes
|
|
orr r6,r6,r6,lsl#16 @ Duplicate
|
|
@str r6,[r0] @ to hdc
|
|
stmia r0,{r2,r6}
|
|
subs r7,r7,#4 @ Dec. number of bytes left
|
|
bne writedma_loop
|
|
|
|
@ If we were too slow we had better go through again - DAG - took out with new interrupt routine
|
|
@ sub r0,r0,#32+8
|
|
@ adr r2,hdc63463_irqdata
|
|
@ ldr r2,[r2,#8]
|
|
@ b writedma_again
|
|
|
|
writedma_end:
|
|
adr r5,hdc63463_irqdata+12
|
|
stmia r5,{r3,r4}
|
|
ldmfd sp!,{r4-r7}
|
|
RETINSTR(mov,pc,lr)
|
|
|
|
@ -------------------------------------------------------------------------
|
|
@ hdc63463_readdma: DMA from controller to host
|
|
@ internal reg usage: r0=hdc base address, r1=irq poll address, r2=poll mask
|
|
@ r3=data ptr, r4=data left, r5,r6=temporary
|
|
.global hdc63463_readdma
|
|
hdc63463_readdma:
|
|
stmfd sp!,{r4-r7}
|
|
adr r5,hdc63463_irqdata
|
|
ldmia r5,{r0,r1,r2,r3,r4}
|
|
|
|
readdma_again:
|
|
@ test number of remaining bytes to transfer
|
|
cmp r4,#0
|
|
beq readdma_end
|
|
bmi readdma_end
|
|
|
|
@ Check the hdc is interrupting
|
|
ldrb r5,[r1,#0]
|
|
tst r5,r2
|
|
beq readdma_end
|
|
|
|
@ Check the hdc is still busy and command has not ended and no errors
|
|
ldr r5,[r0,#32] @ Status reg - 16 bit - its the top few bits which are status
|
|
@ think we should continue DMA until it drops busy - perhaps this was
|
|
@ the main problem with corrected errors causing a hang
|
|
@tst r5,#0x3c00 @ Test for things which should be off
|
|
@bne readdma_end
|
|
and r5,r5,#0x8000 @ This is test for things which should be on: Busy
|
|
cmp r5,#0x8000
|
|
bne readdma_end
|
|
|
|
@ Transfer a block of upto 256 bytes
|
|
cmp r4,#256
|
|
movlt r7,r4
|
|
movge r7,#256
|
|
|
|
@ Bytes remaining at end
|
|
sub r4,r4,r7
|
|
|
|
@ Set a pointer to the data register in the HDC
|
|
add r0,r0,#8
|
|
readdma_loop:
|
|
@ OK - pretty sure we should be doing this
|
|
ldmia r0,{r5,r6}
|
|
mov r5,r5,lsl#16
|
|
mov r6,r6,lsl#16
|
|
orr r6,r6,r5,lsr #16
|
|
str r6,[r3],#4
|
|
subs r7,r7,#4 @ Decrement bytes to go
|
|
bne readdma_loop
|
|
|
|
@ Try reading multiple blocks - if this was fast enough then I do not think
|
|
@ this should help - NO taken out DAG - new interrupt handler has
|
|
@ non-consecutive memory blocks
|
|
@ sub r0,r0,#8
|
|
@ b readdma_again
|
|
|
|
readdma_end:
|
|
adr r5,hdc63463_irqdata+12
|
|
stmia r5,{r3,r4}
|
|
ldmfd sp!,{r4-r7}
|
|
RETINSTR(mov,pc,lr)
|