mirror of
https://github.com/FEX-Emu/linux.git
synced 2024-12-21 00:42:16 +00:00
cfda62baa4
CONFIG_FIREWIRE_OHCI_DEBUG could have been exposed to kernel tweakers if CONFIG_EXPERT was set. But in hindsight, this stuff is far too useful to omit it. So get rid of two #else branches that are only going to bitrot otherwise. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
83 lines
2.8 KiB
Plaintext
83 lines
2.8 KiB
Plaintext
menu "IEEE 1394 (FireWire) support"
|
|
depends on PCI || BROKEN
|
|
# firewire-core does not depend on PCI but is
|
|
# not useful without PCI controller driver
|
|
|
|
config FIREWIRE
|
|
tristate "FireWire driver stack"
|
|
select CRC_ITU_T
|
|
help
|
|
This is the new-generation IEEE 1394 (FireWire) driver stack
|
|
a.k.a. Juju, a new implementation designed for robustness and
|
|
simplicity.
|
|
See http://ieee1394.wiki.kernel.org/index.php/Juju_Migration
|
|
for information about migration from the older Linux 1394 stack
|
|
to the new driver stack.
|
|
|
|
To compile this driver as a module, say M here: the module will be
|
|
called firewire-core.
|
|
|
|
config FIREWIRE_OHCI
|
|
tristate "OHCI-1394 controllers"
|
|
depends on PCI && FIREWIRE && MMU
|
|
help
|
|
Enable this driver if you have a FireWire controller based
|
|
on the OHCI specification. For all practical purposes, this
|
|
is the only chipset in use, so say Y here.
|
|
|
|
To compile this driver as a module, say M here: The module will be
|
|
called firewire-ohci.
|
|
|
|
config FIREWIRE_SBP2
|
|
tristate "Storage devices (SBP-2 protocol)"
|
|
depends on FIREWIRE && SCSI
|
|
help
|
|
This option enables you to use SBP-2 devices connected to a
|
|
FireWire bus. SBP-2 devices include storage devices like
|
|
harddisks and DVD drives, also some other FireWire devices
|
|
like scanners.
|
|
|
|
To compile this driver as a module, say M here: The module will be
|
|
called firewire-sbp2.
|
|
|
|
You should also enable support for disks, CD-ROMs, etc. in the SCSI
|
|
configuration section.
|
|
|
|
config FIREWIRE_NET
|
|
tristate "IP networking over 1394"
|
|
depends on FIREWIRE && INET
|
|
help
|
|
This enables IPv4 over IEEE 1394, providing IP connectivity with
|
|
other implementations of RFC 2734 as found on several operating
|
|
systems. Multicast support is currently limited.
|
|
|
|
To compile this driver as a module, say M here: The module will be
|
|
called firewire-net.
|
|
|
|
config FIREWIRE_NOSY
|
|
tristate "Nosy - a FireWire traffic sniffer for PCILynx cards"
|
|
depends on PCI
|
|
help
|
|
Nosy is an IEEE 1394 packet sniffer that is used for protocol
|
|
analysis and in development of IEEE 1394 drivers, applications,
|
|
or firmwares.
|
|
|
|
This driver lets you use a Texas Instruments PCILynx 1394 to PCI
|
|
link layer controller TSB12LV21/A/B as a low-budget bus analyzer.
|
|
PCILynx is a nowadays very rare IEEE 1394 controller which is
|
|
not OHCI 1394 compliant.
|
|
|
|
The following cards are known to be based on PCILynx or PCILynx-2:
|
|
IOI IOI-1394TT (PCI card), Unibrain Fireboard 400 PCI Lynx-2
|
|
(PCI card), Newer Technology FireWire 2 Go (CardBus card),
|
|
Apple Power Mac G3 blue & white and G4 with PCI graphics
|
|
(onboard controller).
|
|
|
|
To compile this driver as a module, say M here: The module will be
|
|
called nosy. Source code of a userspace interface to nosy, called
|
|
nosy-dump, can be found in tools/firewire/ of the kernel sources.
|
|
|
|
If unsure, say N.
|
|
|
|
endmenu
|