linux/arch/arm/mach-pxa/e750.c
Ian Molton e1c4a2d7b3 [ARM] pxa: add e750 MFP config
Adds MFP configuration for supported e750 hardware.

Signed-off-by: Ian Molton <ian@mnementh.co.uk>
2008-12-31 03:06:57 +00:00

213 lines
5.0 KiB
C

/*
* Hardware definitions for the Toshiba eseries PDAs
*
* Copyright (c) 2003 Ian Molton <spyro@f2s.com>
*
* This file is licensed under
* the terms of the GNU General Public License version 2. This program
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/device.h>
#include <linux/platform_device.h>
#include <linux/fb.h>
#include <linux/mfd/tc6393xb.h>
#include <video/w100fb.h>
#include <asm/setup.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
#include <mach/mfp-pxa25x.h>
#include <mach/pxa-regs.h>
#include <mach/hardware.h>
#include <mach/eseries-gpio.h>
#include <mach/udc.h>
#include <mach/irda.h>
#include "generic.h"
#include "eseries.h"
#include "clock.h"
/* ---------------------- E750 LCD definitions -------------------- */
static struct w100_gen_regs e750_lcd_regs = {
.lcd_format = 0x00008003,
.lcdd_cntl1 = 0x00000000,
.lcdd_cntl2 = 0x0003ffff,
.genlcd_cntl1 = 0x00fff003,
.genlcd_cntl2 = 0x003c0f03,
.genlcd_cntl3 = 0x000143aa,
};
static struct w100_mode e750_lcd_mode = {
.xres = 240,
.yres = 320,
.left_margin = 21,
.right_margin = 22,
.upper_margin = 5,
.lower_margin = 4,
.crtc_ss = 0x80150014,
.crtc_ls = 0x8014000d,
.crtc_gs = 0xc1000005,
.crtc_vpos_gs = 0x00020147,
.crtc_rev = 0x0040010a,
.crtc_dclk = 0xa1700030,
.crtc_gclk = 0x80cc0015,
.crtc_goe = 0x80cc0015,
.crtc_ps1_active = 0x61060017,
.pll_freq = 57,
.pixclk_divider = 4,
.pixclk_divider_rotated = 4,
.pixclk_src = CLK_SRC_XTAL,
.sysclk_divider = 1,
.sysclk_src = CLK_SRC_PLL,
};
static struct w100_gpio_regs e750_w100_gpio_info = {
.init_data1 = 0x01192f1b,
.gpio_dir1 = 0xd5ffdeff,
.gpio_oe1 = 0x000020bf,
.init_data2 = 0x010f010f,
.gpio_dir2 = 0xffffffff,
.gpio_oe2 = 0x000001cf,
};
static struct w100fb_mach_info e750_fb_info = {
.modelist = &e750_lcd_mode,
.num_modes = 1,
.regs = &e750_lcd_regs,
.gpio = &e750_w100_gpio_info,
.xtal_freq = 14318000,
.xtal_dbl = 1,
};
static struct resource e750_fb_resources[] = {
[0] = {
.start = 0x0c000000,
.end = 0x0cffffff,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device e750_fb_device = {
.name = "w100fb",
.id = -1,
.dev = {
.platform_data = &e750_fb_info,
},
.num_resources = ARRAY_SIZE(e750_fb_resources),
.resource = e750_fb_resources,
};
/* -------------------- e750 MFP parameters -------------------- */
static unsigned long e750_pin_config[] __initdata = {
/* Chip selects */
GPIO15_nCS_1, /* CS1 - Flash */
GPIO79_nCS_3, /* CS3 - IMAGEON */
GPIO80_nCS_4, /* CS4 - TMIO */
/* Clocks */
GPIO11_3_6MHz,
/* BTUART */
GPIO42_BTUART_RXD,
GPIO43_BTUART_TXD,
GPIO44_BTUART_CTS,
/* TMIO controller */
GPIO19_GPIO, /* t7l66xb #PCLR */
GPIO45_GPIO, /* t7l66xb #SUSPEND (NOT BTUART!) */
/* UDC */
GPIO13_GPIO,
GPIO3_GPIO,
/* IrDA */
GPIO38_GPIO | MFP_LPM_DRIVE_HIGH,
/* PC Card */
GPIO8_GPIO, /* CD0 */
GPIO44_GPIO, /* CD1 */
GPIO11_GPIO, /* IRQ0 */
GPIO6_GPIO, /* IRQ1 */
GPIO27_GPIO, /* RST0 */
GPIO24_GPIO, /* RST1 */
GPIO20_GPIO, /* PWR0 */
GPIO23_GPIO, /* PWR1 */
GPIO48_nPOE,
GPIO49_nPWE,
GPIO50_nPIOR,
GPIO51_nPIOW,
GPIO52_nPCE_1,
GPIO53_nPCE_2,
GPIO54_nPSKTSEL,
GPIO55_nPREG,
GPIO56_nPWAIT,
GPIO57_nIOIS16,
/* wakeup */
GPIO0_GPIO | WAKEUP_ON_EDGE_RISE,
};
/* ----------------- e750 tc6393xb parameters ------------------ */
static struct tc6393xb_platform_data e750_tc6393xb_info = {
.irq_base = IRQ_BOARD_START,
.scr_pll2cr = 0x0cc1,
.scr_gper = 0,
.gpio_base = -1,
.suspend = &eseries_tmio_suspend,
.resume = &eseries_tmio_resume,
.enable = &eseries_tmio_enable,
.disable = &eseries_tmio_disable,
};
static struct platform_device e750_tc6393xb_device = {
.name = "tc6393xb",
.id = -1,
.dev = {
.platform_data = &e750_tc6393xb_info,
},
.num_resources = 2,
.resource = eseries_tmio_resources,
};
/* ------------------------------------------------------------- */
static struct platform_device *devices[] __initdata = {
&e750_fb_device,
&e750_tc6393xb_device,
};
static void __init e750_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(e750_pin_config));
clk_add_alias("CLK_CK3P6MI", &e750_tc6393xb_device.dev,
"GPIO11_CLK", NULL),
eseries_get_tmio_gpios();
platform_add_devices(devices, ARRAY_SIZE(devices));
pxa_set_udc_info(&e7xx_udc_mach_info);
e7xx_irda_init();
pxa_set_ficp_info(&e7xx_ficp_platform_data);
}
MACHINE_START(E750, "Toshiba e750")
/* Maintainer: Ian Molton (spyro@f2s.com) */
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
.boot_params = 0xa0000100,
.map_io = pxa_map_io,
.init_irq = pxa25x_init_irq,
.fixup = eseries_fixup,
.init_machine = e750_init,
.timer = &pxa_timer,
MACHINE_END