mirror of
https://github.com/FEX-Emu/linux.git
synced 2024-12-27 03:47:43 +00:00
98560bd83e
Also, make DDR latency configurable. Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
119 lines
2.9 KiB
ArmAsm
119 lines
2.9 KiB
ArmAsm
/*
|
|
* DDR SDRAM initialization - alter with care
|
|
* This file is intended to be included from other assembler files
|
|
*
|
|
* Note: This file may not modify r8 or r9 because they are used to
|
|
* carry information from the decompresser to the kernel
|
|
*
|
|
* Copyright (C) 2005-2007 Axis Communications AB
|
|
*
|
|
* Authors: Mikael Starvik <starvik@axis.com>
|
|
*/
|
|
|
|
/* Just to be certain the config file is included, we include it here
|
|
* explicitely instead of depending on it being included in the file that
|
|
* uses this code.
|
|
*/
|
|
|
|
#include <hwregs/asm/reg_map_asm.h>
|
|
#include <hwregs/asm/ddr2_defs_asm.h>
|
|
|
|
;; WARNING! The registers r8 and r9 are used as parameters carrying
|
|
;; information from the decompressor (if the kernel was compressed).
|
|
;; They should not be used in the code below.
|
|
|
|
;; Refer to ddr2 MDS for initialization sequence
|
|
|
|
; 2. Wait 200us
|
|
move.d 10000, $r2
|
|
1: bne 1b
|
|
subq 1, $r2
|
|
|
|
; Start clock
|
|
move.d REG_ADDR(ddr2, regi_ddr2_ctrl, rw_phy_cfg), $r0
|
|
move.d REG_STATE(ddr2, rw_phy_cfg, en, yes), $r1
|
|
move.d $r1, [$r0]
|
|
|
|
; 2. Wait 200us
|
|
move.d 10000, $r2
|
|
1: bne 1b
|
|
subq 1, $r2
|
|
|
|
; Reset phy and start calibration
|
|
move.d REG_ADDR(ddr2, regi_ddr2_ctrl, rw_phy_ctrl), $r0
|
|
move.d REG_STATE(ddr2, rw_phy_ctrl, rst, yes) | \
|
|
REG_STATE(ddr2, rw_phy_ctrl, cal_rst, yes), $r1
|
|
move.d $r1, [$r0]
|
|
move.d REG_STATE(ddr2, rw_phy_ctrl, cal_start, yes), $r1
|
|
move.d $r1, [$r0]
|
|
|
|
; 2. Wait 200us
|
|
move.d 10000, $r2
|
|
1: bne 1b
|
|
subq 1, $r2
|
|
|
|
; Issue commands
|
|
move.d REG_ADDR(ddr2, regi_ddr2_ctrl, rw_ctrl), $r0
|
|
move.d sdram_commands_start, $r2
|
|
command_loop:
|
|
movu.b [$r2+], $r1
|
|
movu.w [$r2+], $r3
|
|
do_cmd:
|
|
lslq 16, $r1
|
|
or.d $r3, $r1
|
|
move.d $r1, [$r0]
|
|
; 2. Wait 200us
|
|
move.d 10000, $r4
|
|
1: bne 1b
|
|
subq 1, $r4
|
|
cmp.d sdram_commands_end, $r2
|
|
blo command_loop
|
|
nop
|
|
|
|
; Set timing
|
|
move.d REG_ADDR(ddr2, regi_ddr2_ctrl, rw_timing), $r0
|
|
move.d CONFIG_ETRAX_DDR2_TIMING, $r1
|
|
move.d $r1, [$r0]
|
|
|
|
; Set latency
|
|
move.d REG_ADDR(ddr2, regi_ddr2_ctrl, rw_latency), $r0
|
|
move.d CONFIG_ETRAX_DDR2_LATENCY, $r1
|
|
move.d $r1, [$r0]
|
|
|
|
; Set configuration
|
|
move.d REG_ADDR(ddr2, regi_ddr2_ctrl, rw_cfg), $r0
|
|
move.d CONFIG_ETRAX_DDR2_CONFIG, $r1
|
|
move.d $r1, [$r0]
|
|
|
|
ba after_sdram_commands
|
|
nop
|
|
|
|
sdram_commands_start:
|
|
.byte regk_ddr2_deselect
|
|
.word 0
|
|
.byte regk_ddr2_pre
|
|
.word regk_ddr2_pre_all
|
|
.byte regk_ddr2_emrs2
|
|
.word 0
|
|
.byte regk_ddr2_emrs3
|
|
.word 0
|
|
.byte regk_ddr2_emrs
|
|
.word regk_ddr2_dll_en
|
|
.byte regk_ddr2_mrs
|
|
.word regk_ddr2_dll_rst
|
|
.byte regk_ddr2_pre
|
|
.word regk_ddr2_pre_all
|
|
.byte regk_ddr2_ref
|
|
.word 0
|
|
.byte regk_ddr2_ref
|
|
.word 0
|
|
.byte regk_ddr2_mrs
|
|
.word CONFIG_ETRAX_DDR2_MRS & 0xffff
|
|
.byte regk_ddr2_emrs
|
|
.word regk_ddr2_ocd_default | regk_ddr2_dll_en
|
|
.byte regk_ddr2_emrs
|
|
.word regk_ddr2_ocd_exit | regk_ddr2_dll_en | (CONFIG_ETRAX_DDR2_MRS >> 16)
|
|
sdram_commands_end:
|
|
.align 1
|
|
after_sdram_commands:
|