mirror of
https://github.com/FEX-Emu/linux.git
synced 2025-02-04 18:18:54 +00:00
efcc2da3fd
It's easier to find bindings descriptions in separate files. So factor out the MTD physmap bindings into a separate file to not clutter booting-without-of.txt more. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
64 lines
2.2 KiB
Plaintext
64 lines
2.2 KiB
Plaintext
CFI or JEDEC memory-mapped NOR flash
|
|
|
|
Flash chips (Memory Technology Devices) are often used for solid state
|
|
file systems on embedded devices.
|
|
|
|
- compatible : should contain the specific model of flash chip(s)
|
|
used, if known, followed by either "cfi-flash" or "jedec-flash"
|
|
- reg : Address range of the flash chip
|
|
- bank-width : Width (in bytes) of the flash bank. Equal to the
|
|
device width times the number of interleaved chips.
|
|
- device-width : (optional) Width of a single flash chip. If
|
|
omitted, assumed to be equal to 'bank-width'.
|
|
- #address-cells, #size-cells : Must be present if the flash has
|
|
sub-nodes representing partitions (see below). In this case
|
|
both #address-cells and #size-cells must be equal to 1.
|
|
|
|
For JEDEC compatible devices, the following additional properties
|
|
are defined:
|
|
|
|
- vendor-id : Contains the flash chip's vendor id (1 byte).
|
|
- device-id : Contains the flash chip's device id (1 byte).
|
|
|
|
In addition to the information on the flash bank itself, the
|
|
device tree may optionally contain additional information
|
|
describing partitions of the flash address space. This can be
|
|
used on platforms which have strong conventions about which
|
|
portions of the flash are used for what purposes, but which don't
|
|
use an on-flash partition table such as RedBoot.
|
|
|
|
Each partition is represented as a sub-node of the flash device.
|
|
Each node's name represents the name of the corresponding
|
|
partition of the flash device.
|
|
|
|
Flash partitions
|
|
- reg : The partition's offset and size within the flash bank.
|
|
- label : (optional) The label / name for this flash partition.
|
|
If omitted, the label is taken from the node name (excluding
|
|
the unit address).
|
|
- read-only : (optional) This parameter, if present, is a hint to
|
|
Linux that this flash partition should only be mounted
|
|
read-only. This is usually used for flash partitions
|
|
containing early-boot firmware images or data which should not
|
|
be clobbered.
|
|
|
|
Example:
|
|
|
|
flash@ff000000 {
|
|
compatible = "amd,am29lv128ml", "cfi-flash";
|
|
reg = <ff000000 01000000>;
|
|
bank-width = <4>;
|
|
device-width = <1>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
fs@0 {
|
|
label = "fs";
|
|
reg = <0 f80000>;
|
|
};
|
|
firmware@f80000 {
|
|
label ="firmware";
|
|
reg = <f80000 80000>;
|
|
read-only;
|
|
};
|
|
};
|