upx/doc/filter.txt

This document explains the concept of "filtering" in UPX. Basically
filtering is a data preprocessing method which could improve the
compression ratio of the files UPX processes.

Currently the filters UPX uses are all based on one very special
algorithm which is working well on ix86 executable files.
This is what upx calls the "naive" implementation. There is also a
"clever" method which works only with 32 bit executable file formats
and was first implemented in UPX.

Let's start with an example (from this point I assume a 32 bit file
format). Consider this code fragment:

00025970: E877410600                     calln     FatalError
00025975: 8B414C                         mov       eax,[ecx+4C]
00025978: 85C0                           test      eax,eax
0002597A: 7419                           je        file:00025995
0002597C: 85F6                           test      esi,esi
0002597E: 7504                           jne       file:00025984
00025980: 89C6                           mov       esi,eax
00025982: EB11                           jmps      file:00025995
00025984: 39C6                           cmp       esi,eax
00025986: 740D                           je        file:00025995
00025988: 83C4F4                         add (d)   esp,F4
0002598B: 68A0A91608                     push      0816A9A0
00025990: E857410600                     calln     FatalError
00025995: FF45F4                         inc       [ebp-0C]

Here you can find two calls to a function called "FatalError". As you
probably know the compression ratio is better if the compressor engine
finds longer sequences of repeated strings. In this case the engine
sees the following two byte sequences:

E877 410600 8B   and
E857 410600 FF.

So it can find a 3-byte-long match.

Now comes the trick. On ix86 near calls are encoded as 0xE8 then a 32
bit relative offset to the destination address. Let's see what
happens if the position of the call is added to that offset:

0x64177 + 0x25970 = 0x89AE7
0x64157 + 0x25990 = 0x89AE7

E8 E79A0800 8B
E8 E79A0800 FF

As you can see now the compressor engine finds a 5-byte-long match.
Which means, that we've just saved 2 bytes of compressed data. Not bad.

So this is the basic idea (the "naive" implementation). All we have to
do is to "filter" the uncompressed data using this method before
compression, and "unfilter" it after decompression. Simply go over the
memory, find 0xE8 bytes and process the next 4 bytes as specified
above.

Of course there are several possibilities where this scheme could be
improved. First, not only calls could be handled this way - near jumps
(0xE9 + 32 bit offset) could work similarly.

A second improvement could be if we limit this filtering only for the
area occupied by real code - there is no point in messing with general
data.

Another improvement comes if the byte order of the 32 bit offset is
reversed. Why? Here is another call which follows the above fragment:

000261FA: E8C9390600                     calln     ErrorF

0x639C9 + 0x261FA = 0x89BC3

E8 C39B 0800     compare this with

E8 E79A 0800

As you can see these two functions are quite close together, but the
compressor is not able to utilize this information (2-byte-long matches
are usually not useful) unless the byte order of the offsets are
reversed. In this case:

E8 0008 9AE7

E8 0008 9BC3

So, the compressor engine finds a 3-byte-long match here. This is a
nice improvement - now the engine utilizes the similarity of nearby
destinations too.

This is nice, but what happens when we find a "fake" call - ie. an 0xE8
which is part of another instruction? Like this:

0002A3B1: C745 E8 00000000               mov       [ebp-18],00000000

In this case those nice 0x00 bytes are overwritten with some less
compressible data. This is the disadvantage of the "naive"
implementation.

So let's be clever and try to detect and process only "real" calls. In
UPX a simple method is used to find these calls. We simply check that
the destinations of these calls are inside the same area as the calls
themselves (so the above code is still a false positive, but it helps
generally). A better method would be to actually disassemble the code -
contributions are welcome :-)

But this is only half of the job. We can not simply process one call
then skip another one - the unfiltering process needs some information
to be able to reverse the filtering.

UPX uses the following idea, which works nicely. First we assume that
the size of the area that should be filtered is less than 16MB. Then
UPX scans over this area and keeps a record of the bytes that are
following the 0xE8 bytes. If we are lucky, there will be bytes that
were not found following 0xE8. These bytes are our candidates to be
used as markers.

Do you still remember that we assumed that the size of scanned area is
less than 16MB? Well, this means that when we process a real call, the
resulting offset will be less than 0x00FFFFFF too. So the MSB is always
0x00. Which is a nice place to store our marker. Of course we should
reverse the byte order in the resulting offset - so this marker will
appear just after the 0xE8 byte and not 4 bytes after it.

That's all. Just go over the memory area, identify the "real" calls,
and use this method to mark them. Then the job of the unfilter is very
easy - it just searches for a 0xE8 + marker sequence and does the
unfiltering if it finds one. It's clever, isn't it? :)

To tell you the truth it's not this simple in UPX. It can use an
additional parameter ("add_value") which makes things a little bit more
complicated (for example it can happen that a found marker is proven to
be unusable because of some overflow during an addition).

And the whole algorithm is optimized for simplicity on the unfiltering
side (as short and as fast assembly as possible - see stub/macros.ash),
which makes the filtering process a little more difficult (fcto_ml.ch,
fcto_ml2.ch, filteri.cpp).

As it can be seen in filteri.cpp, there are lots of variants of this
filtering implemented - native/clever, calls/jumps/calls&jumps,
reversed/unreversed offsets - a sum of 18 slightly different filters
(and another 9 variants for 16 bit programs).

You can select one of them using the command line parameter "--filter="
or try most of them with "--all-filters". Or just let upx use the one
we defined as the default for that executable format.

EOF