mirror of
https://github.com/RPCS3/llvm.git
synced 2024-12-21 11:38:35 +00:00
868e74bdce
Patch by Mikael Lyngvig git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@194794 91177308-0d34-0410-b5e6-96231b3b80d8
70 lines
2.9 KiB
ReStructuredText
70 lines
2.9 KiB
ReStructuredText
===================================================================
|
|
How To Build On ARM
|
|
===================================================================
|
|
|
|
Introduction
|
|
============
|
|
|
|
This document contains information about building/testing LLVM and
|
|
Clang on an ARM machine.
|
|
|
|
This document is *NOT* tailored to help you cross-compile LLVM/Clang
|
|
to ARM on another architecture, for example an x86_64 machine. To find
|
|
out more about cross-compiling, please check :doc:`HowToCrossCompileLLVM`.
|
|
|
|
Notes On Building LLVM/Clang on ARM
|
|
=====================================
|
|
Here are some notes on building/testing LLVM/Clang on ARM. Note that
|
|
ARM encompasses a wide variety of CPUs; this advice is primarily based
|
|
on the ARMv6 and ARMv7 architectures and may be inapplicable to older chips.
|
|
|
|
#. If you are building LLVM/Clang on an ARM board with 1G of memory or less,
|
|
please use ``gold`` rather then GNU ``ld``.
|
|
Building LLVM/Clang with ``--enable-optimized``
|
|
is preferred since it consumes less memory. Otherwise, the building
|
|
process will very likely fail due to insufficient memory. In any
|
|
case it is probably a good idea to set up a swap partition.
|
|
|
|
#. If you want to run ``make check-all`` after building LLVM/Clang, to avoid
|
|
false alarms (e.g., ARCMT failure) please use at least the following
|
|
configuration:
|
|
|
|
.. code-block:: bash
|
|
|
|
$ ../$LLVM_SRC_DIR/configure --with-abi=aapcs-vfp
|
|
|
|
#. The most popular Linaro/Ubuntu OS's for ARM boards, e.g., the
|
|
Pandaboard, have become hard-float platforms. The following set
|
|
of configuration options appears to be a good choice for this
|
|
platform:
|
|
|
|
.. code-block:: bash
|
|
|
|
./configure --build=armv7l-unknown-linux-gnueabihf \
|
|
--host=armv7l-unknown-linux-gnueabihf \
|
|
--target=armv7l-unknown-linux-gnueabihf --with-cpu=cortex-a9 \
|
|
--with-float=hard --with-abi=aapcs-vfp --with-fpu=neon \
|
|
--enable-targets=arm --enable-optimized --enable-assertions
|
|
|
|
#. ARM development boards can be unstable and you may experience that cores
|
|
are disappearing, caches being flushed on every big.LITTLE switch, and
|
|
other similar issues. To help ease the effect of this, set the Linux
|
|
scheduler to "performance" on **all** cores using this little script:
|
|
|
|
.. code-block:: bash
|
|
|
|
# The code below requires the package 'cpufrequtils' to be installed.
|
|
for ((cpu=0; cpu<`grep -c proc /proc/cpuinfo`; cpu++)); do
|
|
sudo cpufreq-set -c $cpu -g performance
|
|
done
|
|
|
|
#. Running the build on SD cards is ok, but they are more prone to failures
|
|
than good quality USB sticks, and those are more prone to failures than
|
|
external hard-drives (those are also a lot faster). So, at least, you
|
|
should consider to buy a fast USB stick. On systems with a fast eMMC,
|
|
that's a good option too.
|
|
|
|
#. Make sure you have a decent power supply (dozens of dollars worth) that can
|
|
provide *at least* 4 amperes, this is especially important if you use USB
|
|
devices with your board.
|